MSZ 10440-1962 《塑料检测 注意!牌》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

GOST 17734-1988 Knee-type millers Standards of accuracy and rigidity《膝形研磨机 精度和刚度标准》.pdf

GOST 17735-1972 Woodworking equipment Veneer guillotine shears Basic parameters《木材加工设备 剪割键榫用龙门剪床 基本参数》.pdf

GOST 17736-1972 Double-ended plain plug gauges with split bushes and inserts from 0 10 up to 0 95 mm nominal diameter Design and dimensions《标称直径为0 10-0 95 mm的带拼合衬套和插件的普通双端塞规 设计和尺寸规.pdf

GOST 17737-1972 Double-ended plain plug-gauges with inset inserts from 0 30 up to 0 95 mm nominal diameter Design and dimensions《标称直径为0 30-0 95 mm的带插件的普通双端塞规 设计和尺寸规格》.pdf

GOST 17738-1972 Plain plug-gauges (go side) with inserts of diameter from 0 30 up to 0 95 mm Design and dimensions《直径0 3mm～0 95mm带镶套光滑通端塞规 结构及尺寸》.pdf

GOST 17739-1972 Plain plug-gauges (not go side) with inserts of diameter from 0 30 up to 0 95 mm Design and dimensions《标称直径为0 30-0 95 mm的带插件的普通塞规(非通过端) 设计和尺寸规格》.pdf

GOST 17740-1972 Double-ended plain plug-gauges with inserts of diameter from 0 30 up to 0 95mm Design and dimensions《标称直径为0 30-0 95 mm的带插件的普通双端塞规 设计和尺寸规格》.pdf

GOST 17741-1972 Double-ended handles for plain plug-gauges with split bushes Design and basic dimensions《带开口衬套光滑塞规用双头手柄 结构及尺寸》.pdf

GOST 17742-1972 Double-ended handles for plain plug-gauges with inset inserts from 1 mm nominal diameter Design and dimensions《标称直径为1 mm的带插件的普通塞规用双端手柄 设计和尺寸规格》.pdf