MSZ 8615-1960 《矮角管螺纹》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSK-M4D796-A2-2010 POLYCARBONATE (PC) MODIFIED HIGH HEAT RESISTANT MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《改良的耐高温聚碳酸酯(PC)模塑材料 与福特WSS-M99P1111-A 一起使用.pdf

FORD WSK-M4D797-A-2010 POLYCARBONATE (PC) 22% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《22%玻璃纤维增强聚碳酸酯(PC)模塑材料 与福特WSS-M99P1111-A 一起使用[使用 福特WSS.pdf

FORD WSK-M4D798-A-2010 POLYETHYLENE (PE) LOW DENSITY FLEXIBLE MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《低密度柔性聚乙烯（PE）成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSK-M4D799-A-2012 POLYETHYLENE (PE) MEDIUM DENSITY LOW MELT FLOW RATE MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《中等密度 低熔态流动率的聚乙烯(PE)模塑材料 与福特WSS-M99P1111-A 一起使用》.pdf

FORD WSK-M4D800-A-2010 POLYETHYLENE (PE) HIGH DENSITY HIGH MELT FLOW RATE LOW IMPACT MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《高密度高熔体流速低抗冲聚乙烯（PE）成型料 与标准FORD WSS-M99P.pdf

FORD WSK-M4D801-A-2010 POLYAMIDE (PA) 12 RIGID HEAT STABILIZED 12% GRAPHITE FILLED MOLDING AND EXTRUSION COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《12%石墨填充的受热稳定的刚性聚酰胺12模塑和挤塑成型.pdf

FORD WSK-M4D802-A-2010 POLYAMIDE (PA) 12 SEMI-FLEXIBLE HEAT STABILIZED MOLDING AND EXTRUSION COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《半柔性、受热稳定的聚酰胺12模塑和挤塑成型料 与标准FORD WSS-M99.pdf

FORD WSK-M4D804-A-2006 POLYAMIDE (PA) 6 HEAT STABILIZED IMPACT MODIFIED BLOW MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《受热稳定的聚酰胺6冲击改性吹塑成型料 与标准FORD WSS-M99P1111-A一起使用 .pdf

FORD WSK-M4D805-A-2013 POLYVINYL CHLORIDE (PVC) FOAM CLOSED CELL TO BE USED WITH FORD WSS-M99P1111-A .pdf