MSZ 9402 37 lap-1961 《纺织材料颜色固定检测 丝光羊毛检测》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSK-M4D637-A3-2005 ACETAL (POM) HOMOPOLYMER MELT FLOW RATE 19-32 TO BE USED WITH FORD WSS-M99P1111-A (Shown on WSK-M4D637-A1)《汽车内部用熔体流动速率为19-32的乙缩醛均聚物(POM)着色成型料 与标准FORD WSS.pdf

FORD WSK-M4D637-A4-2005 ACETAL (POM) HOMOPOLYMER MELT FLOW RATE 34-44 TO BE USED WITH FORD WSS-M99P1111-A (Shown on WSK-M4D637-A1)《汽车内部用熔体流动速率为34-44的乙缩醛均聚物(POM)着色成型料 与标准FORD WSS.pdf

FORD WSK-M4D637-A5-2005 ACETAL (POM) HOMOPOLYMER CHEMICALLY LUBRICATED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《以化学方式润滑的乙缩醛共聚物（POM）成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSK-M4D639-A-2010 POLYBUTYLENE TEREPHTHALATE (PBT) EXTRUSION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚对苯二甲酸丁二醇酯（PBT）挤塑成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSK-M4D641-A-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 25% GLASS FIBER REINFORCED TO BE USED WITH FORD WSS-M99P1111-A (Use WSK-M4D653-A)《25%玻璃纤维增强、受热稳定的聚酰胺66 与标准FORD WSS-M99P1.pdf

FORD WSK-M4D642-A-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 30% GLASS FIBER REINFORCED TO BE USED WITH FORD WSS-M99P1111-A (Use WSK-M4D673-A)《30%玻璃纤维增强、受热稳定的聚酰胺66 与标准FORD WSS-M99P1.pdf

FORD WSK-M4D642-A2-2009 POLYAMIDE (PA) 66 HEAT STABILIZED 30% GLASS FIBER REINFORCED MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用受热稳定、30%玻璃纤维增强的聚酰胺66成型料 .pdf

FORD WSK-M4D642-A3-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 30% GLASS FIBER REINFORCED REDUCED MOISTURE ABSORPTION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A (Use WSK-M4D.pdf

FORD WSK-M4D643-A1-2010 POLYPROPYLENE (PP) HOMOPOLYMER 40% MINERAL FILLED MELT FLOW RATE 4 - 7 TO BE USED WITH FORD WSS-M99P1111-A 《熔体流动速率为4-7的40%矿物填充的聚丙烯(PP)均聚物 与标准FORD WSS-M99.pdf