MSZ 11498-1963 《氧化汞（II）红色分析目标用》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSK-M4D858-A2-2010 POLYCARBONATE + POLYBUTYLENE TEREPHTHALATE BLEND (PC+PBT) MODIFIED MOLDING COMPOUND RECYCLATE EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用回收聚碳酸酯+聚对.pdf

FORD WSK-M4D861-A2-2010 POLYPHTHALAMIDE (PPA) IMPACT MODIFIED 45% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《45%玻璃纤维增强的冲击改性聚邻苯二甲酰胺(PPA)成型料 与标准F.pdf

FORD WSK-M4D864-A3-2008 ABS GENERAL PURPOSE RECOMPOUNDED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《通用丙烯腈-丁二烯-苯乙烯共聚物(ABS)再混成型料 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD ES.pdf

FORD WSK-M4D872-A-1993 POLYPHTHALAMIDE (PPA) 25 % GLASS FIBER REINFORCED MOLDING COMPOUND《25%玻璃纤维增强的聚邻苯二甲酰胺（PPA）成型料》.pdf

FORD WSK-M4D873-A1-2011 THERMOPLASTIC POLYOLEFIN ELASTOMER (TEO) 10% MINERAL FILLED COLOR PIGMENTED MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《10%矿物填充 内部着色热塑性.pdf

FORD WSK-M4D873-A2-2010 THERMOPLASTIC POLYOLEFIN ELASTOMER (TEO) 10% MINERAL FILLED PAINTABLE VIRGIN AND OR RECYCLATE TO BE USED WITH FORD WSS-M99P1111-A 《10%矿物填充可涂装的未利用和 或回收的热塑性.pdf

FORD WSK-M4D876-A1-2009 ABS HIGH HEAT RESISTANT HIGH IMPACT MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯共聚物(ABS)耐高温、高抗冲成型料 与标准FORD WSS-M99P1111-A一起使用 [使用 F.pdf

FORD WSK-M4D876-A2-2011 ABS HIGH HEAT RESISTANT HIGH IMPACT MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSK-M4D876-A1)《内部耐高温耐冲击丙烯腈模塑材料 与福特WSS-M9.pdf

FORD WSK-M4D876-A3-2009 ABS HIGH HEAT RESISTANT HIGH IMPACT MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSK-M4D876-A1)《汽车外部用丙烯腈-丁二烯-苯乙烯共聚物(ABS)耐高.pdf