MSZ 12433 2-1967 《主要技术特征，电力起重能力，速度，最大起吊高度》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

EN ISO 8692-2012 en Water quality - Fresh water algal growth inhibition test with unicellular green algae《水质 用单细胞绿藻进行淡水藻类生长抑制性试验》.pdf

EN ISO 8729-1998 en Ships and marine technology - Marine radar reflectors《船舶和航海技术 航海雷达反射器》.pdf

EN ISO 8733-1997 en Parallel Pins with Internal Thread of Unhardened Steel or Austenitic Stainless Steel《未淬硬钢和奥氏体不锈钢制带内螺纹的等直径销 ISO 8733-1997 代替EN 28733-1992》.pdf

EN ISO 8734-1997 en Parallel Pins of Hardened Steel or Martensitic Stainless Steel (Dowel Pins)《淬硬钢和马氏体不锈钢(定位销)圆柱销 ISO 8734-1997 代替EN 28734-1992》.pdf

EN ISO 8735-1997 en Parrallel Pins with Internal Thread of Hardened Steel or Martensitic Stainless Steel《淬硬钢或马氏体不锈钢内螺纹圆柱销 ISO 8735-1997 代替EN 28735-1992》.pdf

EN ISO 8739-1997 en Grooved Pins - Full-Length Parallel Grooved with Pilot《槽销 带导杆及全长平行沟槽 ISO 8739-1997 代替EN 28739-1992》.pdf

EN ISO 8740-1997 en Grooved Pins - Full-Length Parallel Grooved with Chamfer《槽销 带倒角及全长平行沟槽 代替EN 28740-1992 ISO DIS 8740-1997》.pdf

EN ISO 8741-1997 en Grooved Pins - Half-Length Reverse-Taper Grooved《槽销 半长倒锥槽 ISO 8741-1997 代替EN 28741-1992》.pdf

EN ISO 8742-1997 en Grooved Pins - One-Third-Length Centre Grooved《槽销 中部槽长为1 3全长 ISO 8742-1997 代替EN 28742-1992》.pdf