1、*USACE / NAVFAC / AFCESA / NASA UFGS-26 55 53.00 40 (May 2011)-Preparing Activity: NASA SupersedingUFGS-26 55 53.00 40 (November 2008)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated April 2011*SECTION TABLE OF CONTENTSDIVISION 26 - ELECTRICALSECTION 26 55 53.00 40S
2、ECURITY LIGHTING05/11PART 1 GENERAL1.1 REFERENCES1.2 SUBMITTALS1.3 SYSTEM DESCRIPTION1.3.1 Lighting System1.3.2 Design Requirements for CCTV Assessment Lighting1.3.3 Electrical Requirements1.3.4 Power Line Surge Protection1.3.5 Interface CCTV Lighting and CCTV System1.3.6 Interface Lighting System a
3、nd Power Distribution1.3.7 Nameplates1.3.8 Standard Products1.3.9 Unusual Service Conditions1.3.10 Hazardous Locations1.3.11 Protection of Security Lighting System Components1.3.11.1 Components and Conductors1.3.11.2 Tamper Provisions1.3.12 Spare Parts1.4 CORROSION PROTECTION1.4.1 Aluminum Materials
4、1.4.2 Ferrous Metal Materials1.4.2.1 Hardware1.4.2.2 Equipment1.4.3 FinishingPART 2 PRODUCTS2.1 STANDARD PRODUCT2.2 CABLE2.2.1 Insulated Cable2.2.2 Messenger Cable2.2.3 Bare Copper Conductors2.3 AERIAL CABLE HARDWARE2.4 CABLE SPLICES AND CONNECTORS2.5 CABLE BOXESSECTION 26 55 53.00 40 Page 1Provided
5、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.6 MANHOLES, HANDHOLES, AND PULLBOXES2.7 CONDUIT, DUCTS AND FITTINGS2.7.1 Conduit, Rigid Steel2.7.2 Conduit Coatings2.7.3 Conduit Fittings and Outlets2.7.3.1 Boxes, Metallic Outlets2.7.3.2 Boxes, Nonmetallic,
6、Outlet and Flush-Device Boxes and Covers2.7.3.3 Boxes, Outlet for Use in Hazardous (Classified) Locations2.7.3.4 Boxes, Switch (Enclosed), Surface Mounted2.7.3.5 Fittings for Conduit and Outlet Boxes2.7.3.6 Fittings for Use in Hazardous (Classified) Locations2.7.3.7 Fittings, PVC, for Use with Rigid
7、 PVC Conduit and Tubing2.7.4 Non-Metallic Duct2.8 ELECTRICAL ENCLOSURES2.8.1 Interior Enclosures2.8.2 Exposed-to-Weather Enclosures2.8.3 Corrosion Resistant Enclosures2.8.4 Hazardous Environment Enclosures2.9 ILLUMINATION2.9.1 General Lighting2.9.2 Roadway Lighting2.10 LAMPS AND BALLASTS, HIGH INTEN
8、SITY DISCHARGE (HID) SOURCES2.10.1 High-Pressure Sodium2.10.2 Mercury Vapor2.10.3 Metal-Halide2.11 LAMPS, INCANDESCENT2.12 LAMPS, FLUORESCENT2.13 LUMINAIRE COMPONENTS2.14 PHOTOMETRIC DISTRIBUTION CLASSIFICATION2.15 LUMINAIRES, FLOODLIGHTING2.15.1 HID and Incandescent2.15.2 Fluorescent2.16 FIXTURES2.
9、16.1 Accessories2.16.2 Special Fixtures2.16.3 In-Line Fuse2.17 SEARCHLIGHTS2.18 FRESNEL-LENS LUMINAIRES2.19 TRANSFORMERS2.19.1 Outdoor Dry-Type Lighting Transformers2.19.2 Buck-Boost Transformers2.20 WIREWAY, RAINTIGHT, SUPPORTPART 3 EXECUTION3.1 GENERAL3.1.1 Current Site Conditions3.1.2 Existing Eq
10、uipment3.2 ENCLOSURE PENETRATIONS3.3 PREVENTION OF CORROSION3.3.1 Aluminum3.3.2 Steel Conduits3.3.3 Cold Galvanizing3.4 CABLE INSTALLATION3.4.1 Splices3.4.2 Installation in Duct Lines3.4.3 Direct Burial3.4.3.1 Trenching3.4.3.2 Requirements for Installation in DuctSECTION 26 55 53.00 40 Page 2Provide
11、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.4.3.3 Location of Cable Splices3.4.3.4 Markers3.4.3.5 Warning Tape3.4.4 Messenger Cable3.4.4.1 Installation3.4.4.2 Grounding and Bonding Connections3.4.4.3 Grounding Conductors and Electrodes3.4.4.4 Ground R
12、esistance Testing3.5 AERIAL CABLE SPLICES3.6 LASHING WIRE3.7 STRESS LOOPS3.8 CONNECTIONS TO BUILDINGS3.9 DUCT LINES3.9.1 Requirements3.9.2 Treatment3.9.3 Concrete Encasement3.9.4 Nonencased Direct-Burial3.9.5 Installation of Couplings3.9.6 Concrete3.9.7 Duct Line Markers3.10 HANDHOLES3.10.1 Construc
13、tion3.10.2 Appurtenances3.10.3 Cable Pulling-In Irons3.10.4 Ground Rods3.11 LIGHTING3.11.1 Lamps3.11.2 Fixture Installation3.11.2.1 Accessories3.11.2.2 In-Line Fuses3.11.2.3 Special Fixtures3.12 TRANSFORMER INSTALLATION3.13 CCTV ALARM INTERFACE3.14 TESTS3.14.1 Testing For CCTV Assessment Lighting3.1
14、4.2 Operating Test3.14.3 Ground Resistance Measurements3.14.4 Record Drawings- End of Section Table of Contents -SECTION 26 55 53.00 40 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-26 55 53.00 40 (May 201
15、1)-Preparing Activity: NASA SupersedingUFGS-26 55 53.00 40 (November 2008)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated April 2011*SECTION 26 55 53.00 40SECURITY LIGHTING05/11*NOTE: This guide specification covers the requirements for lighting for security and cl
16、osed circuit television (CCTV) area illumination.Use and coordinate UFGS Section 26 09 23.00 40 LIGHTING CONTROL DEVICES for control devices (includes tailoring for exterior lighting) with this section.Use and coordinate UFGS Section 26 56 13.00 40LIGHTING POLES AND STANDARDS for pole or standard, i
17、ncluding mounting and base accessories of exterior fixtures with this section.Use and coordinate UFGS Section 26 56 19.00 40 ROADWAY LIGHTING for roadway and street lighting with this section.Use UFGS Section 26 56 23.00 40 AREA LIGHTING for lighting system requirements for exterior area lighting an
18、d recreational areas.Use UFGS Section 26 56 36.00 40 FLOOD LIGHTING for facility and grounds flood lighting.Adhere to UFC 1-300-02 Unified Facilities Guide Specifications (UFGS) Format Standard when editing this guide specification or preparing new project specification sections. Edit this guide spe
19、cification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirements not required in respective project, whether or not brackets are present.Comments, suggestions and
20、recommended changes for this guide specification are welcome and should be submitted as a Criteria Change Request (CCR).SECTION 26 55 53.00 40 Page 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*PART 1 GENERAL*NOTE: This specification does not inc
21、lude provision for high-mast roadway and parking lot lighting (poles over 18.3 meters (60 feet). Requirements for materials and procedures for special or unusual design will be added as necessary for specific projects. Quantity and quality of illumination will conform to UFC 3-550-03FA, “Electrical
22、Power Supply and Distribution“. Standard details will conform to the general requirements of UFC 3-550-03FA, “Electrical Power Supply and Distribution“ and may be modified to suit project conditions.Do not use Incandescent lamps, Fluorescent lamps, and Mercury Vapor Lamps for CCTV area illumination,
23、 nor tungsten lamps other than infrared lamps.Two types of infrared luminaires are currently available: fixtures with special lamps utilizing optical dichroic mirror coatings that produce only infrared light, and fixtures that use conventional lamps that pass the light output through infrared filter
24、s. Special lamps have the advantage of operating cooler and not requiring a cooling fan, thus operating quieter and requiring less maintenance.The major disadvantages are high lamp replacement cost due to short bulb life (2000 to 4000 hours) and special lamp design. The 2000 hour lamps produce more
25、infrared light energy and are preferred over the 4000 hour lamps. Another disadvantage is the limited variety of wattages available, but this is normally resolved by fixture placement during site lighting system design. Conventional lamps utilizing special power supplies and infrared filters have th
26、e advantages of low bulb replacement cost and bulb life ranging from 1700 to 18000 hours. (Note: Special power supplies reduce current flow to the bulb and allow it to operate at a lower filament temperature to shift light output more into the near infrared (NIR) light spectrum and requires less fil
27、tering. This has the additional advantage of extending bulb life.) A variety of bulb sizes are available and no special bulbs are required. The main disadvantage of using a conventional bulb is the heat generated utilizing an infrared filter which must be cooled by a cooling fan. Fans require mainte
28、nance and the loss of the fan will destroy the filter. Filters are expensive.*1.1 REFERENCES*SECTION 26 55 53.00 40 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTE: This paragraph is used to list the publications cited in the text of the g
29、uide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically place
30、the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the issue dates.References not used in the text will automatically be deleted from this section of the project specification when you choose to reconcile references in the publish print process.*
31、The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.ASTM INTERNATIONAL (ASTM)ASTM A123/A123M (2009) Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Pro
32、ductsASTM A153/A153M (2009) Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel HardwareASTM A48/A48M (2003; R 2008) Standard Specification for Gray Iron CastingsASTM A575 (1996; R 2007) Standard Specification for Steel Bars, Carbon, Merchant Quality, M-GradesASTM A576 (1990b; R 2006
33、) Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special QualityASTM B 117 (2009) Standing Practice for Operating Salt Spray (Fog) ApparatusASTM B 2 (2008) Standard Specification for Medium-Hard-Drawn Copper WireASTM B 8 (2004) Standard Specification for Concentric-Lay-Stranded Copper C
34、onductors, Hard, Medium-Hard, or SoftASTM C 478 (2009) Standard Specification for Precast Reinforced Concrete Manhole SectionsASTM D 1654 (2008) Evaluation of Painted or Coated SECTION 26 55 53.00 40 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
35、,-,-Specimens Subjected to Corrosive EnvironmentsILLUMINATING ENGINEERING SOCIETY OF NORTH AMERICA (IESNA)IESNA RP-8 (2000; Errata 2004; R 2005; Errata 2007) Roadway LightingINSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS (IEEE)IEEE 81 (1983) Guide for Measuring Earth Resistivity, Ground Impedance
36、, and Earth Surface Potentials of a Ground SystemIEEE C135.1 (1999) Standard for Zinc-Coated Steel Bolts and Nuts for Overhead Line ConstructionIEEE C135.30 (1988) Standard for Zinc-Coated Ferrous Ground Rods for Overhead or Underground Line ConstructionIEEE C2 (2007; Errata 06-1; TIA 07-1; TIA 07-2
37、; TIA 07-3; Errata 07-2; TIA 08-4; TIA 08-5; TIA 08-6; TIA 08-7; TIA 08-8; TIA 08-9; TIA 08-10; TIA 08-11; TIA 09-12; TIA 09-13; TIA 09-14; Errata 09-3; TIA 09-15; TIA 09-16; TIA 10-17) National Electrical Safety CodeIEEE C62.41.1 (2002; R 2008) Guide on the Surges Environment in Low-Voltage (1000 V
38、 and Less) AC Power CircuitsIEEE C62.41.2 (2002) Recommended Practice on Characterization of Surges in Low-Voltage (1000 V and Less) AC Power CircuitsNATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA)ANSI ANSLG C78.42 (2009) For Electric Lamps: High-Pressure Sodium LampsANSI C119.1 (2011) Electric
39、 Connectors - Sealed Insulated Underground Connector Systems Rated 600 VoltsANSI C136.11 (2006) American Standard for Roadway Lighting Equipment Series Sockets and Series Sockets ReceptaclesANSI C136.15 (2011) American National Standard for Roadway Lighting Equipment - High-Intensity-Discharge and L
40、ow-Pressure Sodium Lamps in Luminaires - Field IdentificationANSI C136.2 (2004; R 2009) American National Standard for Roadway and Area Lighting Equipment: SECTION 26 55 53.00 40 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Luminaires Voltag
41、e ClassificationANSI C136.3 (2005; R 2009) American National Standard for Roadway and Area Lighting Equipment Luminaire AttachmentsANSI C136.6 (2004) American National Standard for Roadway Lighting Equipment - Metal Heads and Reflector Assemblies - Mechanical and Optical InterchangeabilityANSI C136.
42、9 (2003) American National Standard for Roadway and Area Lighting Equipment - Socket Support Assemblies for Metal Heads - Mechanical InterchangeabilityANSI C78.40 (1992; R 2003) American National Standard for Mercury Lamps-SpecificationsANSI C80.1 (2005) American National Standard for Electrical Rig
43、id Steel Conduit (ERSC)ANSI C82.4 (2002) American National Standard for Ballasts for High-Intensity-Discharge and Low-Pressure Sodium (LPS) Lamps (Multiple-Supply Type)ANSI/ANSLG C78.43 (2007) American National Standard for Electric Lamps - Single-Ended Metal-Halide LampsANSI/NEMA OS 1 (2008; Amd 20
44、10) Sheet-Steel Outlet Boxes, Device Boxes, Covers, and Box SupportsNEMA 250 (2008) Enclosures for Electrical Equipment (1000 Volts Maximum)NEMA ICS 6 (1993; R 2006) EnclosuresNEMA RN 1 (2005) Polyvinyl-Chloride (PVC) Externally Coated Galvanized Rigid Steel Conduit and Intermediate Metal ConduitNEM
45、A TC 6 R 2002) Interface Between Data Terminal Equipment and Data SECTION 26 55 53.00 40 Page 8Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Circuit-Terminating Equipment Employing Serial Binary Data InterchangeUNDERWRITERS LABORATORIES (UL)UL 1029
46、 (1994; Reprint Jun 2010) High-Intensity-Discharge Lamp BallastsUL 1449 (2006; Reprint Feb 2011) Surge Protective DevicesUL 1598 (2008; Reprint Jan 2010) LuminairesUL 44 (2010) Thermoset-Insulated Wires and CablesUL 467 (2007) Grounding and Bonding EquipmentUL 486A-486B (2003; Reprint Feb 2010) Wire ConnectorsUL
