1、INTERNATIONAL TRUCK AND ENGINE CORPORATION TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: TMS- 4505 ITITLE: Enamel, Air Drv, Texture Finish IREVZSZ*AJ: c - 1 I WRiTTEN/EDITED BY: Materials Engineering APPROVED BY: DATE ISSUED Materials Engineering September 2000 befereme: File 30-13A Keywords: Enamel; A
2、ir Dry Paint; Texture Paint I 1.0 APPLICATION This specification covers an air dry vinyl modified, acrylic alkyd paint suitable for achieving a textured finish on fiberglass reinforced plastic parts, as described in TMS-9000. 2.0 SCOPE This specification covers the property and performance requireme
3、nts, approved materials and an approved source list. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following standards, specifications and regulations are referenced in this specification. Quality System Standard QS-9000 (IS0 9001)
4、INTERNATIONAL CEMS GT-2B FSTM 4250 INTERNATIONAL IQR Quality Standard INTERNATIONAL CEMS GT-4D FSTM 41 84.1 INTERNATIONAL Mfg. Standard D-13 INTERNATIONAL CEMS GT-SA ASTM D 56 INTERNATIONAL TMS 9000 INTERNATIONAL CEMS GT-7D ASTM D 562 CFR Title 29, Part 1910 INTERNATIONAL CEMS GT-1 INTERNATIONAL CEM
5、S GT-3B INTERNATIONAL CEMS GT-7E INTERNATIONAL CEMS GT-7G 4.0 REOUIREMENTS 4.1 Liquid Properties 4.1.1 Non-Volatile Content: CEMS GT-1 Percentage by weight. min Color Code NAV 2300 (Tahitian Red) NAV 8550 (Gray) NAV 1622 (Rawhide) NAV 0006 (Dark Brown) NAV 9220 (White) Weight % 41.8 f 2 45.6 f 2 46.
6、8 f 2 44.5 f 2 49.6 f 2 This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 02000 International Truck and Engine Corporation SEPT
7、EMBER 2000 Page 1 of 3 NUMBER: TMS-4505 4.1.2 Weight per Unit Volume: FSTM4184.1 Color NAV 2300 NAV 8550 NAV 1622 NAV 0006 NAV 9220 TITLE: REVISION: Enamel, Air Dry, Texture Finish c-1 kghiter 1.08 f 0.02 1.08 f 0.02 1.14 f 0.02 1.09 f 0.02 1.17 f 0.02 lbmkallon 9.0 f 0.2 9.0 f 0.2 9.5 f 0.2 9.1 f 0
8、.2 9.8 f 0.2 4.1.3 The liquid properties listed in this section apply to all colors. 4.1.3.1 Flash Point: ASTM D-56 Shall be 27C (81F) minimum 4.1.3.2 Viscosity, As Received: ASTM D-562 Shall be 70-80 Kreb Units (or equivalent) 4.1.3.3 Storage Stability: CEMS GT-3B Shall meet the appearance requirem
9、ents of this storage stability test. 4.1.3.4 Dry Film Properties (All Colors) The following tests shall be performed on panels prepared and painted per TMS-9000. The panels shall be a min of 100 x 100 mm (4 x 4 in) or 100 mm (4 in) diameter cut from production parts. 4.1.3.5 Hiding Power: CEMS GT-2B
10、 Shall require a maximum dry film thickness of 25 pm (1 mil) to completely hide the black and gray Morest chart. 4.1.3.6 Weatherometer (250 Hours) Shall show no evidence of color change, cracking, or checking. 4.1.3.7 Hardness: CEMS GT-4D Shall be 2B minimum 4.1.3.8 Curing Properties on Receipt Shal
11、l be tack free after 15 minutes at 21-27C (70-80F). 4.1.3.9 Adhesion: CEMS GT-SA Shall exhibit 90% adhesion after the specified testing. 4.1.3.10 Salt Spray: CEMS GT-7D Shall exhibit no evidence of blistering and a maximum creepage of 0.8 mm (0.03 in) after 250 hours testing. 4.1.3.11 Humidity: CEMS
12、 GT-7E Shall exhibit no evidence of blistering immediately after removal from the humidity cabinet after 100 hours testing. 4.1.3.12 Water Immersion: CEMS GT-7G Shall exhibit no blistering or color change after 48 hours testing. 4.2.9 Color: FSTM 4250 Shall meet the requirements of FSTM 4250. 4.2.10
13、 Heat Stabilitv Panels heated in oven for 30 minutes at 120C (250F) shall exhibit no color change. This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume
14、all patent liability. 02000 International Truck and Engine Corporation SEPTEMBER 2000 Page 2 of 3 NUMBER: TMS-4505 5.0 OUALIFICATION Material shall be purchased only from sources approved by Truck Development and Technology Center. Manufacturers wishing to supply material shall first certify complia
15、nce to all the requirements herein. Then, samples must be supplied to the TDTC for qualification testing. TITLE: REVISION: Enamel, Air Dry, Texture Finish c-1 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requirements Suppliers must conform to the requirements of the INTERNATIONAL IQR Standar
16、d which includes conformance to the QS-9000 (IS0 9001) Quality System Standard. A mutually acceptable Quality Control Plan as described therein is required for source approval to the requirements of this specification. 6.2 Approval Parts supplied against contracts or purchase orders citing this spec
17、ification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the prod
18、uct are required, the supplier shall notify Truck Development and Technology Center and International Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety
19、 Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 6.3 Process Control The supplier shall either perform and report results of tests on specific lots of parts produced or provide statistical evidence of the lot having been produced in a
20、state of statistical control and with a process capable of providing all required properties. The part supplier and the plant metallurgist andor the quality control manager of the using International plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING A
21、ND IDENTIFICATION Loading, packing and identification shall be in accordance with Manufacturing Std. D-13. 8.0 DESIGNATION ON DRAWINGS Paint (Material) per TMS-4505 NOTE: Drawings shall also reference TMS-9000 for “Method of Application“ 9.0 APPROVED SOURCES Pontiac Coatings, Inc. 30 Brush Street, P
22、.O. Box 45 Pontiac, MI 48056 9.1 Approved Materials 1) White - Pontiac Code NAV 1023 2) Brown - Pontiac Code NAV 860 3) Rawhide - Pontiac Code NAV1022 4) Tahitian Red - Pontiac Code NAV 1008 5) Gray - Pontiac Code NAV 101 1 This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 02000 International Truck and Engine Corporation SEPTEMBER 2000 Page 3 of 3
