1、This document is restricted and may not be sent outside Navistar, Inc., or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2013 by Navistar, Inc. OCTOBER 2013 Page 1 of 2 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER
2、: TMS-9544 TITLE: Flammability Certification of Interior Trim Materials And Components CURRENT REV. NO: 1310 DATE: October 2013 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev. B - August 2003 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT RE
3、VISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regu
4、latory limits prior to use. Change Notice: Added Sections 2.1, 7.0, and 8.0; editorial changes. Reference: File: 16-7, 50-9 Keywords: Certification; Interior Trim, Flammability 1.0 APPLICATION This specification applies to those interior trim materials and components whose controlling material speci
5、fications reference this specification for certification to FMVSS 302 requirements and/or to the School Bus Seat Upholstery Fire Block Test as described in the latest version of the National School Transportation Specifications and Procedures publication. 2.0 SCOPE This specification covers general
6、and compliance requirements. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified the latest issue of all refer
7、enced standards shall apply. The following Specifications, Standards, and Regulations are referenced in this specification. SAE J369 National School Transportation Specifications and Procedures * CFR Title 49, Part 571 FMVSS 302 TMS-9543 CEMS B-50 *Available from: Missouri Safety Center, Central Mis
8、souri State University, Humphreys Suite 201 Warrenburg, MO 64093 4.0 GENERAL REQUIREMENTS Other NAVISTAR specifications which refer to this specification include materials which must comply with FMVSS-302 or the School Bus Seat Fire Block Test. Those materials shall meet all requirements of Federal
9、Motor Vehicle Safety Standard 302 - Flammability of Interior Materials, and all requirements of SAE J369 - Flammability of Polymeric Interior Materials; and the School Bus Seat Fire Block Test, and with the applicable codes of each state or province, as applicable. 4.1 The finished composite must co
10、nform to and be certified to meet all requirements of FMVSS-302. Parts of the assembly/composite which are not 100% bonded together shall be tested separately and each NUMBER: TMS-9544 TITLE: Flammability Certification Of Interior Trim Materials And Components REVISION: 1310 This document is restric
11、ted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2013 by Navistar, Inc. OCTOBER 2013 Page 2 of 2 component must demonstrate required flammability resistance. Components of the co
12、mposite which are 100% bonded together are not specifically required to demonstrate flammability resistance when tested separately as individual parts, however; the bonded composite must demonstrate the required flammability resistance. 4.2 Compliance Requirements Supplier shall provide proof of com
13、pliance by submission of compliance test reports. The test report or the report cover letter shall follow the report format described in TMS-9543. The report should be addressed to the Director of Body Engineering (see address below). A new compliance test report shall be generated for any significa
14、nt manufacturing process or material changes. In addition to requirements set forth by FMVSS 302 and/or SAE J 369, and/or the School Bus Seat Fire Block Test, the report will include the following information: 4.2.1 Complete identification of materials tested 4.2.2 Test conditions 4.2.3 Test results
15、, including burn rate, if applicable. 4.2.4 Copies of each Compliance Report shall be sent to the Quality Manager of each Navistar facility using the product, as well as the following: Director - Body Engineering Navistar, Inc. 2601 Navistar Dr. Lisle, IL 60532 5.0 QUALITY (Not Applicable) 6.0 SOURC
16、E APPROVAL AND QUALITY CONTROL (Not Applicable) 7.0 DESIGNATION ON DRAWINGS Documents or drawings which reference this specification should indicate: Compliance to TMS-9544 is required. 8.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact:
17、 Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Ave. Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/
