1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. NOVEMBER 2016 Page 1 of 8 NAVISTAR, INC. TMS (Truck Material Specifications) Title
2、: TMS-MPAPS Cross Reference Index Index Revision: 1645 November 2016 Author(s): Materials Engineering Approver(s): Materials Engineering Supersedes Issue of: 1642 October 2016 PRINTED COPIES OF THESE DOCUMENTS MUST BE VERIFIED FOR CURRENT REVISION PLEASE CHECK STATUS OF EACH SPEC ON THIS LIST, SINCE
3、 MANY HAVE NOT YET BEEN PUBLISHED. FOR QUESTIONS, CONTACT MATERIALSENGINEERINGNAVISTAR.COM Document No. Title MPAPS Replacement MPAPS Y-XXXX = Active TMS XXXX, MPAPS Y-XXXX = Void or Not-Yet-Created TMS XXXX = Stabilized- Active for current records but not to be applied to any new record (drawing, D
4、RD, DVP&R, DFMEA, RVD item, Specification, etc) . For new records, contact Materials Engineering for replacement. TMS-1xxx Ferrous Metals, Wrought TMS-1001 Mirror Assembly, Exterior MPAPS A-1001 TMS-1002 Bolts, Special Locking, Case Hardened Made Void TMS-1011 Frame Rails - High Strength, Heat Treat
5、ed Steel MPAPS A-1011 TMS-1013 Frame Steel, Ultra High-Strength, Heat-Treated MPAPS A-1013 TMS-1021 Carburizing Steels Made Void TMS-1022 Rear Axle Housings (Non-International Design) VOID MPAPS P-9540 TMS-1026 Ball Stud, High Strength, Wear Resistant MPAPS A-1026 TMS-1029 Low Carbon Steel, Welded,
6、Hardened, and/or Plated Made Void TMS-1031 Steel Tubing, Power Transmission MPAPS A-1031 TMS-1033 Shafts, Steel Induction Hardened Make Void TMS-1034 Steels, Medium Carbon, Quenched and Tempered Made Void TMS-1037 Multi-Leaf Springs MPAPS A-1037 TMS-1041 Antenna Steel, Precipitation Hardening Stainl
7、ess Made Void TMS-1042 Mounting Bolts for Seat Belt Anchorage MPAPS F-1042 TMS-1044 Tapered Leaf and Air Ride Control Arm Suspension Springs MPAPS A-1044 TMS-1045 Corrosion Resistant Steel Tubing MPAPS F-1045 TMS-1050 Flexible Steel Hose MPAPS F-1050 TMS-1051 Shaft Components Make Void TMS-1053 U-Bo
8、lts, High Strength MPAPS F-1053 TMS-1054 Tube, Oil Level Gauge and Fill MPAPS F-1054 TMS-1055 Spring Pins MPAPS A-1055 TMS-1056 Rear Axle Housing (International Design) MPAPS A-1056 TMS-1057 Striker Pin Assembly, Door Lock MPAPS A-1057 TMS-1058 Steel Tubing for Engine Air/Fluid System MPAPS F-1058 T
9、MS-1059 Aluminum Tubing for Engine Air/Fluid System MPAPS C-1059 TMS-1060 Stainless Steel Clad Aluminum Bumpers MPAPS C-1060 TMS-1061 Small Diameter Tubing for Engine Air/Fluid System MPAPS F-1058 TMS-1062 Clamps, Spring Tension, Type CTB MPAPS F-1062 TMS-1064 Suspension Stabilizer Bars MPAPS A-1064
10、 Written and Approved by: Materials Engineering NAVISTAR, INC. Truck Material Specifications TMS-MPAPS Cross Reference Index This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume al
11、l patent liability. 2016 by Navistar, Inc. NOVEMBER 2016 Page 2 of 8 Document No. Title MPAPS Replacement TMS-1065 Tapered Roller Bearings for Wheel End Applications MPAPS A-1065 TMS-1066 Driveline Components MPAPS A-1066 TMS-1067 Steel Wheels MPAPS A-1067 TMS-1068 Bellows Flexible Pipe MPAPS F-1068
12、 TMS-1069 Steel Tubing for Engine Exhaust Systems MPAPS F-1069 TMS-1070 Air Springs, Suspension Component (Restricted) MPAPS P-1070 TMS-2xxx Ferrous Metals, Cast TMS-2008 Equalizer Beam Castings Made Void TMS-2009 Nodular Iron, Pitman Arms Made Void TMS-2014 Gray Cast Iron, Brake Drum MPAPS E-2014 T
13、MS-2017 Ferrous Castings Made Void TMS-3xxx Non-Ferrous, Aluminum TMS-3000 Rivets Break Mandrel Blind Type Made Void TMS-3100 Tubing, Copper, Air Brake MPAPS C-3100 TMS-3101 Heat Exchangers Made Void TMS-3102 Cast Aluminum Wheels MPAPS C-3102 TMS-4xxx Surface Coatings, Chemical Conversion TMS-4002 P
14、re-Paint Treatment of Aluminum MPAPS G-9009 TMS-41xx Coatings, Metallic TMS-4102 Decorative Chromium Plating on Steel MPAPS G-19 Pt I TMS-4103 Decorative Chromium Plating on Aluminum MPAPS G-19 Pt I TMS-4106 Seat Belt Hardware Corrosion Resistance MPAPS G-4106 TMS-4107 Decorative Chrome Plate - Exte
15、rnal Fasteners Made Void TMS-4108 Screws, Corrosion Resistant MPAPS G-4108 TMS-4110 Paint, Primer, Zinc Rich, Weldable Made Void TMS-4113 Black Electrodeposited Organic Coating for Decorative Interior Applications MPAPS G-4113 TMS-4114 Decorative Chrome Plating on Zinc Die Castings MPAPS G-19 Pt I T
16、MS-4115 Weldable Primer on Steel MPAPS G-4115 TMS-4116 Decorative Chromium Plating on Stainless Steel MPAPS G-19 Pt I TMS-4117 Finish Requirements for Stainless Steel Parts MPAPS A-37 TMS-45xx Coatings, Non-Metallic TMS-4502 Painting, Metal or Plated Plastics MPAPS P-4502 TMS-4505 Enamel, Air Dry, T
17、exture Finish MPAPS G-4505 TMS-4508 Metric Blue Identification MPAPS G-4508 TMS-4510 Coating, Weld Through, Corrosion-Resistant, Hot Melt MPAPS G-4510 TMS-4513 Strippable Protective Coatings MPAPS G-4513 TMS-4514 Ink-Striping Cross-Linked Polyethylene Wire Insulation MPAPS G-4514 TMS-4516 Corrosion
18、Preventive Compound MPAPS G-4516 Written and Approved by: Materials Engineering NAVISTAR, INC. Truck Material Specifications TMS-MPAPS Cross Reference Index This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Sup
19、pliers are required to assume all patent liability. 2016 by Navistar, Inc. NOVEMBER 2016 Page 3 of 8 Document No. Title MPAPS Replacement TMS-4517 Interior Trim Panels-Wood Grain MPAPS G-4517 TMS-4518 Corrosion Protective Coatings for Fasteners MPAPS G-4518 TMS-4519 Black Corrosion-Resistant Cathodi
20、c E-coat Finish MPAPS G-4519 TMS-4520 Black, Corrosion Resistant Zinc-Aluminum Coating MPAPS G-4520 TMS-4523 Corrosion-Resistant Zinc-Aluminum Integrally Lubricated Inorganic Coating MPAPS G-4523 TMS-4524 Fluorocarbon Coating for Fasteners MPAPS G-4524 TMS-4525 Corrosion Protective Coating for Use w
21、ith Treated Wood MPAPS G-4525 TMS-5xxx Powdered Metal TMS-5003 Powdered Metal Crankshaft Adapters To be combined w/CEMS H-1 TMS-5004 Powdered Metal Bushings, Weldable “ TMS-5012 Powdered Metal Spacers “ TMS-5015 Powdered Metal Spacer “ TMS-6xxx Rubber, Dense TMS-6003 Wire Reinforced Air Duct MPAPS L
22、-6003 TMS-6004 Pads, Rubber Plied MPAPS L-6004 TMS-6007 Molded Rubber MPAPS L-6007 TMS-6008 Masticated Rubber Sheet MPAPS L-6008 TMS-6012 Power Steering High Pressure Hose MPAPS F-6012 TMS-6016 Hose, High Temperature, with End Fittings MPAPS F-6016 TMS-6021 Hose, Air Conditioner MPAPS F-6021 TMS-602
23、3 Steering Wheel and Horn Pad Assemblies MPAPS L-6023 TMS-6028 Hose, Fuel and Oil Resistant, Filler Neck MPAPS F-6028 TMS-6032 Hose, Fuel and Oil Resistant, Low Pressure MPAPS F-6032 TMS-6033 Air Duct, Engine, Clean Air MPAPS F-6033 TMS-6034 Hose, Turbo MPAPS F-6034 TMS-6036 Air Brake Hose and Hose
24、Assemblies, Permanent Fittings, Type A, MPAPS F-6036 TMS-6037 Hydraulic Brake Hose MPAPS F-6037 TMS-6038 Rubber Hood Straps MPAPS L-6038 TMS-6039 Rubber (TSR) Molding Compounds MPAPS L-6039 TMS-6039-R-BC Rubber (TSR) Molding Compounds (Restricted) - Barry Controls MPAPS L-6039-R-BC TMS-6039-R-Tennec
25、o Rubber (TSR) Molding Compounds (Restricted) - Tenneco MPAPS L-6039-R-Tenneco TMS-6039-R-Trelleborg Rubber (TSR) Molding Compounds (Restricted) - Trelleborg MPAPS L-6039-R-Trelleborg TMS-6039-R-Semyung Rubber (TSR) Molding Compounds (Restricted) Semyung MPAPS L-6039-R-Semyung TMS-6040 Thermoplastic
26、 Elastomer Molding Compounds MPAPS L-6040 TMS-6041 Flooring Components, Bus MPAPS L-6041 TMS-6042 Brake Hose, Low Pressure, Hydraulic MPAPS F-6042 Written and Approved by: Materials Engineering NAVISTAR, INC. Truck Material Specifications TMS-MPAPS Cross Reference Index This document is restricted a
27、nd may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. NOVEMBER 2016 Page 4 of 8 Document No. Title MPAPS Replacement TMS-6044 Rear Hood Mounting MPAPS L-6044 TMS-604
28、5 Door and Body Seals (Rubber) MPAPS K-6045 TMS-6046 Elastomeric Coatings MPAPS G-6046 TMS-6050 CNG Vent Lines and Fuel Hoses with End Fittings & Tube Assemblies MPAPS F-6050 TMS-65xx Rubber, Foam TMS-6500 Cellular Polyurethane, Integral Skin MPAPS L-6500 TMS-6501 Molded Seats, Urethane Foam MPAPS L
29、-6501 TMS-6502 Urethane, Cellular, Molded MPAPS L-6502 TMS-6505 Urethane Foam, Cut Slab MPAPS L-6505 TMS-6506 Urethane Foam, Slush Material MPAPS L-6506 TMS-6509 Treated Urethane Foam, Acoustical MPAPS L-6509 TMS-6510 Urethane Foam, Low Permeability MPAPS L-6510 TMS-6511 Foam Recirculation Seals MPA
30、PS L-6511 TMS-6512 Foam and Sponge, Static Sealing MPAPS L-6512 TMS-6513 Impact Energy Absorbing Foam MPAPS L-6513 TMS-66xx Insulators (Sound, Thermal) TMS-6601 Sound Deadener, Polymeric Molded & Sheet MPAPS L-6601 TMS-6606 Insulation, Floor Mat, Dash and Carpet (E-5 Type) MPAPS L-6606 TMS-6608 Floo
31、r Mat, High Density Rubber, Sound Barrier MPAPS L-6608 TMS-6609 Molded Fiberglass, Cab Insulator MPAPS L-6609 TMS-6610 Thermal Insulation MPAPS L-6610 TMS-6611 Insulation, Heat Shrinkable Tubing MPAPS L-6611 TMS-6612 Insulation, Acoustic MPAPS L-6612 TMS-6614 Piping Insulation MPAPS L-6614 TMS-68xx
32、Fuels and Lubricants TMS-6801 Grease, High Temperature Resistant MPAPS B-6801 TMS-6803 Transmission Gear Lubricant MPAPS B-6803 TMS-6810 Lubricant, Power Steering (Ross and Sheppard) MPAPS B-6810 TMS-6811 Lubricant, Power Steering MPAPS B-6811 TMS-6812 Lubricant, Transmission (Automatic) MPAPS B-681
33、2 TMS-6814 Lubricant, Corrosion Control (Disk Brakes) MPAPS B-6814 TMS-6815 Sheet Metal Processing Lubricants MPAPS B-6815 TMS-6816 Synthetic Transmission and Axle Gear Lubricants MPAPS B-6816 TMS-6817 Wax Lubricants for Threaded Nuts and Fasteners MPAPS B-6817 TMS-6818 Refrigeration Lubricants MPAP
34、S B-6818 TMS-6819 Grease, Dielectric MPAPS B-6819 TMS-6820 Brake Fluid DOT 3 MPAPS B-6820 Written and Approved by: Materials Engineering NAVISTAR, INC. Truck Material Specifications TMS-MPAPS Cross Reference Index This document is restricted and may not be sent outside Navistar, Inc. or reproduced w
35、ithout permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. NOVEMBER 2016 Page 5 of 8 Document No. Title MPAPS Replacement TMS-69xx Adhesives, Sealers, and Tapes TMS-6900 Structural Adhesives, Part 1 and Part 2 MPAPS K-6900 TMS-
36、6904 Tape, Plastic Electrical, Adhesive Tape MPAPS K-6904 TMS-6907 Sealer, Butyl Rubber, Gun Grade MPAPS K-6907 TMS-6910 Cellular Vinyl Tape (Sealing) Combined w/MPAPS L-6512 TMS-6913 Electrical Sealant MPAPS K-6913 TMS-6914 Sealer Tape, Door MPAPS K-6914 TMS-6915 Heat Curing Sealant, Body Cabs MPAP
37、S K-6915 TMS-6916 Adhesive/Sealant, Heat Expanding MPAPS K-6916 TMS-6917 Sealant Tape, Extruded MPAPS K-6917 TMS-6918 Sealer, Assembled Parts MPAPS K-6918 TMS-6925 Moisture Cured and Air Cured, Pumpable Materials MPAPS K-6925 TMS-6926 Sealant, Clear, Water Borne Made Void TMS-6927 Glass Bonding: Par
38、t I and Part II MPAPS K-6927 TMS-6928 Sealant, Preformed Patches MPAPS K-6928 TMS-6929 Mounting Tapes Part 1 and Part 2 MPAPS K-6929 TMS-6930 Glass Assembly Adhesive MPAPS K-6930 TMS-6931 Bus Floor Mat and Step Tread Adhesives MPAPS K-6931 TMS-6933 Wood Joining Adhesives MPAPS K-6933 TMS-7xxx Plasti
39、cs, Fabrics TMS-7000 ABS, Unfilled, Molded MPAPS D-7000 TMS-7005 Thread, Nylon or Dacron MPAPS D-7005 TMS-7006 Non-Metallic Tubing, Air Brake MPAPS F-7006 TMS-7016 Polyvinyl Chloride Extrusions (Trim) MPAPS D-7016 TMS-7028 Bonded Trim Composites, Interior MPAPS D-7028 TMS-7029 Coiled Nylon Air Brake
40、 Tubing MPAPS F-7029 TMS-7039 Polyethylene, Unfilled Molded MPAPS D-7039 TMS-7040 Polypropylene, Unfilled Molded MPAPS D-7040 TMS-7051 Decorative Electroplated Chromium - Plastics MPAPS G-7051 TMS-7055 Acetals, Molded MPAPS D-7055 TMS-7057 Anaerobic Compounds MPAPS D-7057 TMS-7066 Laminated Fiberboa
41、rd, Head Board MPAPS D-7066 TMS-7067 Non-Woven Padding, Fiberbond MPAPS D-7067 TMS-7072 Foundation Board, Door Trim MPAPS D-7072 TMS-7078 Polypropylene, Talc-Filled, Molded MPAPS D-7078 TMS-7079 Bright Decorative Metallizing Plastics MPAPS G-7079 TMS-7081 Polypropylene, Chemically Coupled Glass Rein
42、forced Fan Shrouds Made Void TMS-7085 Second Surface Decorative Finish, Plastic MPAPS G-7085 TMS-7086 Decorative Hot Stamp Roll Leaf Coating - Plastics MPAPS G-7086 TMS-7088 Ticking, Mattress Cover MPAPS D-7088 TMS-7089 Plastic Gears, Speedometer Made Void TMS-7095 Material, Process, and QCR for Ope
43、n Molded FRP Parts MPAPS D-7095 TMS-7097 Vinyl-Coated Paper (Veneer) Made Void Written and Approved by: Materials Engineering NAVISTAR, INC. Truck Material Specifications TMS-MPAPS Cross Reference Index This document is restricted and may not be sent outside Navistar, Inc. or reproduced without perm
44、ission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. NOVEMBER 2016 Page 6 of 8 Document No. Title MPAPS Replacement TMS-7099 Fastener Tape Systems MPAPS F-7099 TMS-7100 PVC Injection Molding Compound MPAPS D-7100 TMS-7101 Thermoplas
45、tic Engine Air Intake System Components MPAPS D-7101 TMS-7102 Mineral/Glass-Filled Nylon MPAPS D-7102 TMS-7105 Modified Polyphenylene-Oxide, Heater Blower Housing Made Void TMS-7107 Interior Wood Grain Decorative Films MPAPS G-7107 TMS-7109 Molded Fiberglass Headliner Made Void TMS-7110 Encapsulated
46、 or Molded Product Badges MPAPS D-7110 TMS-7111 Grille, Exterior, Thermoplastic, Prime Painted MPAPS D-7111 TMS-7113 Woven or Knit Fabric, Interior Trim - Parts 1 and 2 MPAPS D-7113 TMS-7116 Injection Molded Interior Trim Materials MPAPS D-7116 TMS-7117 Foam Composite Trim Panel MPAPS D-7117 TMS-711
47、9 Plastic Aerodynamic Components MPAPS D-7119 TMS-7120 Sunvisors MPAPS D-7120 TMS-7121 Vinyl Coated Interior Trim and Seating Materials MPAPS D-7121 TMS-7124 Interior Structural Foam RIM MPAPS D-7124 TMS-7125 Composite Trim Panels MPAPS D-7125 TMS-7126 Carpet Trim Materials MPAPS D-7126 TMS-7127 Mat
48、tresses MPAPS D-7127 TMS-7129 Coolant Deaeration Reservoir- Polypropylene Copolymer MPAPS D-7129 TMS-7130 Material, Process and QC requirements for Non-SMC Compression Molded Parts MPAPS D-7130 TMS-7131 Driver Air Bag (DAB) MPAPS D-7131 TMS-7133 Material, Process, and Quality Control Requirements fo
49、r Liquid Composite Molded Parts MPAPS D-7133 TMS-7134 Non-Metallic Tubing and Fittings, Fuel Systems MPAPS F-7134 TMS-7135 Plywood and Wood Fiber Sheet Products MPAPS D-7135 TMS-7136 Cab Retention Straps MPAPS D-7136 TMS-7137 Nonmetallic Tubing for SCR Systems MPAPS F-7137 TMS-9xxx Painting TMS-9000 Texture Paint Processing Procedure MPAPS
