1、.- .f.“ 1 f 4. AA-T-2753 73 m 9999974 00631242 4 m AA-T- 2753 30 April 1991 TABLE, FOLDING, STEEL TUBE (ADVANCE BASE) This specification is approved by the Commissioner, Federal Supply Service, General Services Administration, for the use of all Federal agencies. 1. SCOPE AND CLASSIFICATION 1.1 Scop
2、e. This document covers requirements for component materials and their assembly into sturdily constructed folding tables 30 inches high with laminated plastic top surfacing, steel frame, and steel legs, * 1.2 Classification. The folding tables covered by this specification shall be of the sizes as s
3、pecified. PIN Code No Grade I - 30“ high, steel frame and legs, laminated plastic top 1 Size 1 - 30 inches by 48 inches (top). Size 2 - 30 inches by 72 inches (top). A B 2, APPLICABLE DOCUMENTS * 2.1 Government documents. 2.1.1 Specifications. standards, and handbooks. The following specifications,
4、standards, and handbooks of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation, form a part of this specification to the extent specified herein. IBeneficial comments (recommendations, additions, deletions) and any
5、 pertinent1 )data which may be of use in improving this document should be addressed to: I ICommanding Officer (Code 156), Naval Construction Battalion Center, Port I IHueneme, CA 93043-5000, by using the self-addressed Standardization I Idocument or bv letter. I Document Improvement Proposal (DD Fo
6、rm 1426) appearing at the end of this I AMSC N/A FSC 7105 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. e Licensed by Information Handling ServicesAA-T-2753 71 = 9999974 0063243 b AA-T-2753 SPECIFICATIONS FEDERAL L-P-508 - Plastic Sheet, Laminated, Decorative and
7、Non-decorative. PPP-B-636 - Boxes, Shipping, Fiberboard. MI LI TARY MIL-P-116 - Preservation, Methods of STANDARDS FEDERAL FED-STD-595 - Colors. MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-2073 - DOD Materiel Procedu
8、res For Development 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 Defects None Defined Requirement Paragraph Overall dimensions not as specified. 1.1 & 1.2 Table top core not as specified. 3.4.1 Laminated plastic sheets not as specified. 3.4.2 Edging not as specified. 3.4.3 Fasteners n
9、ot as specified. 3.4.4 Aluminum edging not firmly secured in Joints between laminated plastic and Chassis frame dimension not as specified. 3.5.2.1 Chassis frame not in true alignment. 3.5.2.1 Leg of each angle of each chassis frame adjacent to underside of top does not lie flat without buckles at a
10、ll points. Leg assembly materials and dimensions not place. 3.5.1 aluminum edging not tight and smooth. 3.5.1 3.5.2.1 as specified. 3.5.3 Locking device not as specified. 3.5.3 folded. 3.5.3 Legs cannot be fully extended or folded. 3.5.3 Folding arms or leg brace on each side of paired legs travel n
11、ot in unison when legs are not extended or folded. 3.5.3 Legs travel not in unison when extended or 7 Licensed by Information Handling ServicesAA-T-2753 71 9999974 OObL249 7 = - - AA-T-2753 116 117 118 * i19 120 121 122 123 124 125 126 Uneven leg lengths at floor contact points. Legs catch or stick
12、when being extended or Legs do not lock in place when extended in 3.5.3 folded. 3.5.3 use position, or when folded, remain rigid 3.5.3 Color coordination not as specified. 3.6.1 Paint application not as specified. 3.6.2 & 3.7.4 Table underside not treated as specified. 3.6.3 Surface metal cracked, c
13、ontains burrs, or rough edges. 3.7.1 Metal buckled, distorted, or bent out of shape, affecting serviceability or appearance when in use position. metal surfaces that could cause injury or tear clothing. 3.7.1 Sharp edges or protrusions in wood or 3.5.1 i 3.7.1 Welding not as specified. 3.7.3 Paintin
14、g not as specified, 3.7.4 4.5 Tests. Each sample table selected shall be Set-up in the use position and an evenly distributed static load of 1,000 pounds shall be placed on the table for a period of 5 minutes, specified shall be considered a defective unit. Any table failing to sustain the load as 4
15、.6 Packanin5 - inspection. The preservation, packing, and marking of the tables shall be inspected to determine compliance with the requirements of Section 5 of this specification. 5. PACKAGING 5.1 Preservation. Preservation shall be level A or commercial, as specified (see 6.2). 5.1.1 Level A. Each
16、 table shall be folded flat and preserved method III in accordance with MIL-P-116. conforming to PPP-B-636, class weather-resistant. The box shall be closed method V in accordance with the appendix to PPP-B-636. The unit pack container shall be a box * 5.1.2 Commercial. Each table shall be folded fl
17、at and packaged in accordance with ASTM D3951. Requirements as a minimum shall conform to applicable carrier rules and regulations. 5.2 Packing. Packing shall he level A, BI or commercial as specified (see 6.2). * 5.2.1 Levels A and B. Packing shall be accordance with MIL-STD-2073-1A for the applica
18、ble level specified. appendix Cl Table VI1 for the appropriate level. Containers shall be selected from * 5.2.2 Commercial. Material shall be packed in accordance with ASTM D3951. and regulations. Requirements as a minimum shall conform to applicable carrier rules 5.3 Marking, Marking shall be in ac
19、cordance with MIL-STD-129. 8 a Licensed by Information Handling ServicesAA-T-2753 71 W 9999974 00b1250 3 AA-T-2753 6. NOTES 6.1 Intended use. This is intended to be a replacement for MIL-T-23153C. is intended for use in advance base functions as a general purpose utility worktable. The folding legs
20、table covered by this specification * 6.2 Ordering data. Purchasers shall select the preferred Options permitted herein and include the following information in procurement documents : a. b. d. C. e. f. g. h. Title, number, and date of this specification Quantity of tables required. Size required (s
21、ee 1.2). When first article is required for inspection and approval (see 3.3, 4.2.1 and 6.3). Color required (see 3.4.2, 3.6.1, 3.7.4 and table I). Fasteners required (see 3.4.4). Level of preservation and level of packing required (see 5.1 and 5.2). Grade and class or PIN required (see 1.2). 6.3 Fi
22、rst article. When a first article inspection is required, the item will be tested and should be a first article sample or it may be a standard production item from the contractors current inventory as specified in 4.2.1. The first article should consist of one complete table unit. officer should inc
23、lude specific instructions in acquisition documents regarding arrangements for examination, test, and approval of the first article. The contracting * 6.4 Changes from previous issue. Asterisks are used in this revision to identify changes with respect to the previous issue. * 6.5 Part or Identifvin
24、g Number (PIN). items covered by this specification for cataloging purposes. consists of this specification identifier (M2753) and the SPN code number (see 1.2). PINS were developed to identify The PIN The PIN shall be designated as follows: B - 1 PIN designation M2753 - I Specification number I I I
25、 I I I I I I Grade I Class/Type I The above identifies a grade 1 steel (frame and legs) table with a top size of 30 x 48 l. 9 Licensed by Information Handling ServicesAA-T-2753 71 7777774 O063253 5 AA-T-2753 MILITARY INTERESTS: MCA: Navy - YD Custodians: Navy - YD Air Force - 99 Review Activity: Army - GL Air Force - 84 CIVIL AGENCY COORDINATING ACTIVITIES: GSA - FSS/FCNE Preparing activity: Navy - YD (Project 7105-0260) 10 Licensed by Information Handling Services
