NAVY MIL-A-23595 D (1)-2000 AMPLIFIER AUDIO FREQUENCY《音频扩音器》.pdf

上传人:testyield361 文档编号:976891 上传时间:2019-03-13 格式:PDF 页数:2 大小:48.20KB
下载 相关 举报
NAVY MIL-A-23595 D (1)-2000 AMPLIFIER AUDIO FREQUENCY《音频扩音器》.pdf_第1页
第1页 / 共2页
NAVY MIL-A-23595 D (1)-2000 AMPLIFIER AUDIO FREQUENCY《音频扩音器》.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、W b 2124191 688 W INCH-POUND I MIL-A-23595D(AS) AMENDMENT 1 25 February 2000 MILITARY SPECIFICATION AMPLIFIER AUDIO FREQUENCY This amendment forms a part of MIL-A-23595D(AS), dated 14 April 1995, and is approved for use by the Naval Air Systems Command, Department of Navy, and is available for use b

2、y all Departments and Agencies of the Department of Defense. PAGE 19 4.7.23: FIGURE 4: Add after 1 sentence: “The line of force shall extend 0.50 inch minimum beyond the end of the pins.” PAGE 3 1 Replace: “FIGURE 4” with new “FIGURE 4” AMSC N/A 1 of2 FSC 5831 DISTRIBUTION STATEMENT A: Approved for

3、public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-0b 2B24L2 5L4 MIL-A-23595D(AS) AMENDMENT 1 NEEW VALVE REGULATOR I AIR SOURCE I PISTON DRIVEN AIR CYLINDER T - PULLSHAFT DIGITAL STRAIN SENSOR I i CENSOR UNE -L

4、OAD CELL PULL CABLE - AMP PIN +i 0.50 INCH 2 PIN PULL BLOCK - AMPLIFIER - AMPUFIER - FIXTURE FIXTURE BASE SUPPORT ARM - NOTE: This figure illustrates a typical test configuration only. Any equivalent test method is acceptable to achieve the end results as described in MIL-A-23595(AS) paragraph 3.4.3.1. FIGURE 4. TvDid amdifier DI stress to breakage test configuration. - Preparing activity: (Project No. 5831-N124) Navy - AS 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • DIN EN ISO 5167-1-2004 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1 General principles and .pdf DIN EN ISO 5167-1-2004 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1 General principles and .pdf
  • DIN EN ISO 5167-2-2004 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2 Orifice plates (ISO 516.pdf DIN EN ISO 5167-2-2004 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2 Orifice plates (ISO 516.pdf
  • DIN EN ISO 5167-3-2004 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3 Nozzles and Venturi noz.pdf DIN EN ISO 5167-3-2004 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3 Nozzles and Venturi noz.pdf
  • DIN EN ISO 5167-4-2004 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 4 Venturi tubes (ISO 5167.pdf DIN EN ISO 5167-4-2004 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 4 Venturi tubes (ISO 5167.pdf
  • DIN EN ISO 5167-5-2016 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 5 Cone meters (ISO 5167-5.pdf DIN EN ISO 5167-5-2016 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 5 Cone meters (ISO 5167-5.pdf
  • DIN EN ISO 5171-2010 Gas welding equipment - Pressure gauges used in welding cutting and allied processes (ISO 5171 2009) German version EN ISO 5171 2010《气焊设备 焊接 切割和相关工艺用压力计(ISO 51.pdf DIN EN ISO 5171-2010 Gas welding equipment - Pressure gauges used in welding cutting and allied processes (ISO 5171 2009) German version EN ISO 5171 2010《气焊设备 焊接 切割和相关工艺用压力计(ISO 51.pdf
  • DIN EN ISO 5172-2015 Gas welding equipment - Blowpipes for gas welding heating and cutting - Specifications and tests (ISO 5172 2006 + Amd 1 2012 + Amd 2 2015) German version EN IS.pdf DIN EN ISO 5172-2015 Gas welding equipment - Blowpipes for gas welding heating and cutting - Specifications and tests (ISO 5172 2006 + Amd 1 2012 + Amd 2 2015) German version EN IS.pdf
  • DIN EN ISO 5173-2012 Destructive tests on welds in metallic materials - Bend tests (ISO 5173 2009 + Amd 1 2011) German version EN ISO 5173 2010 + A1 2011《金属材料焊接点无损检测试验 弯曲试验》.pdf DIN EN ISO 5173-2012 Destructive tests on welds in metallic materials - Bend tests (ISO 5173 2009 + Amd 1 2011) German version EN ISO 5173 2010 + A1 2011《金属材料焊接点无损检测试验 弯曲试验》.pdf
  • DIN EN ISO 5178-2011 Destructive tests on welds in metallic materials - Longitudinal tensile test on weld metal in fusion welded joints (ISO 5178 2001) German version EN ISO 5178 2.pdf DIN EN ISO 5178-2011 Destructive tests on welds in metallic materials - Longitudinal tensile test on weld metal in fusion welded joints (ISO 5178 2001) German version EN ISO 5178 2.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1