NAVY MIL-C-28858 A (2)-1989 COUPLER GROUP ANTENNA OA-9123 SRC《OA-9123 SRC天线耦合器组》.pdf

上传人:lawfemale396 文档编号:977722 上传时间:2019-03-13 格式:PDF 页数:3 大小:101.39KB
下载 相关 举报
NAVY MIL-C-28858 A (2)-1989 COUPLER GROUP ANTENNA OA-9123 SRC《OA-9123 SRC天线耦合器组》.pdf_第1页
第1页 / 共3页
NAVY MIL-C-28858 A (2)-1989 COUPLER GROUP ANTENNA OA-9123 SRC《OA-9123 SRC天线耦合器组》.pdf_第2页
第2页 / 共3页
NAVY MIL-C-28858 A (2)-1989 COUPLER GROUP ANTENNA OA-9123 SRC《OA-9123 SRC天线耦合器组》.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、MIL-C-2SA (2) 57 M 7777906 0053V38 3 M MIL-C-28858A( EC AMENDMENT 2 20 July 1989 SUPtRSEDING AMENDMENT 1 23 May 1986 MILITARY SPECIFICATION COUPLER GROUP , ANTENNA, OA-9123ISRC This amendment forms a part of Military Specification MIL-C-28858A(EC), dated 2 December 1985, and is approved for use by t

2、he Space and Naval Warfare Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 2 2.1.1 , “STANDARDS“ , “MILITARY“ after “MIL-STD-415“ , add: 2.1.1, “STANDARDS“, “MILITARY“ after “DoD-STD-1686“, add: “MIL-STD-454 - Stand

3、ard General Requirements For Electronic Equipment. * “MIL-STD-2000 Standard Requirements For Sol dered Electrical And Electronic Asseinbl ies“. * 2.1.2, “PUBLICATIONS : Delete: “NAVAL AIR SYSTEMS COMMAND ( NAVA1 R W S-6 536D Process Specification Procedures And Requirements For Preparation And Sol d

4、ering Of Electrical Connections“ and substi tute: “DEPARTMENT OF DEFENSE ( DoD DoD 4245.7M Transi tion From Devel opment To Production“. AMSC NIA 1 of 3 FSC 5985 DISTRIBUTION STATEMENT A. Approved for pub1 ic release; distri bution is un1 imi ted. Provided by IHSNot for ResaleNo reproduction or netw

5、orking permitted without license from IHS-,-,-MI L-C-28858A( EC ) AMENDMENT 2 PAGE 3 3.1, last sentence: Delete. PAGE 4 * Delete “3.2.2.4“ and substitute “3.3.2.4“. PAGE 5 * * . 3.4.2.2, 1 ine 2: Delete “paragraph“ and substitute “paragraphs“. * 3.4.2.2, to end of line 1: Add “Operating temperature

6、ranges and“. After “3,5.1“, add the following new paragraph: “3.5.1.1 Parts rescreening. Parts rescreening shall be conducted in accordance with DoD 4245 ,7M under piece part control . II. PAGE 7 Delete “excced“ and substitute “exceed“. 3.6.7, line 2: * 3.6.12.1: Delete and substitute: shall operate

7、 compatibly in the intended electromagnetic environment. The production units shall comply with the requirements of MIL-STD-461, Part 5, Class A4, including hardening against the effects of an electromagnetic pulse (EMP), conducted and radiated. Compliance shall be verified in accordance with the te

8、st procedures of MIL-STD-462.“. * 3.6.12.2, title: Delete and substitute IIEMP.“. - “3.6.12.1 E3 control. The multicoupler shall be self-compatible and PAGE 9 3.7.2: Delete and substitute: “3.7.2 Controls, indicators, and panels. The controls, indicators, and operator and maintenance panels shall co

9、nform to the criteria of MIL-STD-1472, The color coding and marking of pin jacks and other test points shall be in accordance with MIL-STD-415. Abbreviations used on panels shall conform to MIL-STD-12.“. * “herein . II 3.10, line 2: Delete “in 3.10.1 through 3.10.4.1. and Substitute 2 A- Provided by

10、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-28858A (2) 57 m 7779706 0053440 I m MIL-C-28858A( EC) AMENDMENT 2 PAGE 10 3.14.1, first sentence: Delete and substitute: “Workmanship shall 3.14.1, line 3: conform to MIL-STD-454, Requirement 9. II. * Delete

11、 “WS 6536D.“ and substitute “MIL-STD-2000, Task F.“, PAGE 13 * 4.5.7: Delete and substitute: “4.5.7 El ec tromagneti c compati bi 1 i ty ( EMC 1. EMC veri fica ti on tes ti ng shall be in accordance with MIL-S1D-462. ADDlicable tests include CEO1, CE03, CSO1, CS02, CS06, CS11, REO1, RE02, RSO1, RS02

12、 RS03, and RS05. limit may be relaxed by 20 dB at fundamental frequencies of operation in the narrowband mode. II. The REO2 PAGE 20 * 4.8.2.2, line 1: Delete 10“ and substitute “15“. * 4.8.2.2, line 2: Delete “5C“ and substitute “10C“. PAGE 25/26 APPENDIX A: Delete. The margins of this amendment ar

13、e marked with an asterisk to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are ca

14、utioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Preparing activity: NAVY - EC (Project No. 5985-N597(EC) .- 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • KS W ISO 5858-2008 Aerospace-Nuts self-locking with maximum operating temperature less than 425℃-Procurement specification《航空航天 最高工作温度小于或等于425℃的自锁螺母的采购规范》.pdf KS W ISO 5858-2008 Aerospace-Nuts self-locking with maximum operating temperature less than 425℃-Procurement specification《航空航天 最高工作温度小于或等于425℃的自锁螺母的采购规范》.pdf
  • KS W ISO 5884-2007 Aerospace-Fluid systems and components-Methods for system sampling and measuring the solid particle contamination of hydraulic fluids《航空航天 液压系统和组件 液压流体固体微粒污染的系统取.pdf KS W ISO 5884-2007 Aerospace-Fluid systems and components-Methods for system sampling and measuring the solid particle contamination of hydraulic fluids《航空航天 液压系统和组件 液压流体固体微粒污染的系统取.pdf
  • KS W ISO 6702-1-2008 Aircraft-Requirements for on-board weight and balance systems-Part 1:General《航空器 舱内装载和平衡系统的要求 第1部分 总则》.pdf KS W ISO 6702-1-2008 Aircraft-Requirements for on-board weight and balance systems-Part 1:General《航空器 舱内装载和平衡系统的要求 第1部分 总则》.pdf
  • KS W ISO 6773-2002 Aerospace-Fluid systems-Thermal shock testing of piping and fittings《航空航天流体系统管道及配件的热冲击试验》.pdf KS W ISO 6773-2002 Aerospace-Fluid systems-Thermal shock testing of piping and fittings《航空航天流体系统管道及配件的热冲击试验》.pdf
  • KS W ISO 7169-2009 Aerospace-Separable tube fittings for fluid systems for 24 cones for pressures up to 3 000 psi or 21 000 kPa-Procurement specification inch metric《航空航天 液压系统用24锥形.pdf KS W ISO 7169-2009 Aerospace-Separable tube fittings for fluid systems for 24 cones for pressures up to 3 000 psi or 21 000 kPa-Procurement specification inch metric《航空航天 液压系统用24锥形.pdf
  • KS W ISO 7481-2005 Aerospace-Nuts self-locking with maximum operatingtemperature less than or equal to 425 ℃-Test methods《航空航天 最高工作温度小于或等于425℃的自锁螺母 试验方法》.pdf KS W ISO 7481-2005 Aerospace-Nuts self-locking with maximum operatingtemperature less than or equal to 425 ℃-Test methods《航空航天 最高工作温度小于或等于425℃的自锁螺母 试验方法》.pdf
  • KS W ISO 8074-2009 Aerospace-Surface treatment of austenitic stainless steel parts《航空航天 奥氏体不锈钢零件的表面处理》.pdf KS W ISO 8074-2009 Aerospace-Surface treatment of austenitic stainless steel parts《航空航天 奥氏体不锈钢零件的表面处理》.pdf
  • KS W ISO 8080-2002 Aerospace-Anodic treatment of titanium and titanium alloys-Surfuric acid process《航空航天 钛和钛合金的阳极处理 硫酸工艺法》.pdf KS W ISO 8080-2002 Aerospace-Anodic treatment of titanium and titanium alloys-Surfuric acid process《航空航天 钛和钛合金的阳极处理 硫酸工艺法》.pdf
  • KS W ISO 8168-2005 Aerospace-Corrosion-and heat-resisting steel bolts with strength classification 1 100 MPa and MJ threads-Procurement specification《航空航天系列 强度等级为1100MPa、带MJ螺纹的耐腐蚀和.pdf KS W ISO 8168-2005 Aerospace-Corrosion-and heat-resisting steel bolts with strength classification 1 100 MPa and MJ threads-Procurement specification《航空航天系列 强度等级为1100MPa、带MJ螺纹的耐腐蚀和.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1