1、CCiS -CS MIL-C-bob83 (2) 13 = 999990b 0390872 8 m - MI L-C-60683 (OS) AMENDMENT 2 15 JULY 1986 SUPERSEDING AMENDMENT 1 27 JULY 1973 MILITARY SPEC I FI CATION CATAPULT, AIRCRAFT EJECTION SEAT: M4A1 REMANUFACTURED METAL PARTS ASSEMBLY This amendment forms a part of Military Specification MIL-C-60683(M
2、U), dated 17 February 1971, and is approved for use within the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 * 2.2 Delete in its entirety and substitute: “2.2 Other publications. The following document
3、 forms a part of this specification t the extent specified herein. Unless otherwise specified, the issues of the document which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS
4、 shall be the issue of the nongovernment documents which is current on the date of the sol i ci tation. ANSI B46.1-78 Surface Texture (Surface Roughness, Waviness and Lay) Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this documen
5、t should be addressed to: Standardization Branch (5241), Indian Head, MD 20640-5000, by using the se 1 f -add res sed Standard i za t i on Do cume n t Improvement Proposa 1 (DD Form 1426) appearing at the end of the specification or by letter, Commanding Officer, Naval Ordnance Station, AMSC N/A FSC
6、 1377 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited, THIS DOCUMENT CONTAINS ( 5 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-bob83 (2) lr3 44777Ob 0340873 T W MI L-C-60683( OS) AMENDMENT 2 15 JULY 1
7、986 (Application for copies should be addressed to the American National Standards Insti tute (ANSI) , 1430 Broadway, NY 10018. ) (Nongovernment standards and other pub1 ications are normally available from the organization which prepares or which distri butes the documents. These documents also may
8、 be available in or through libraries or other informational servi ces. )I1 PAGE 5 4.2.1.2, delete in its entirety and substitute: metal parts assemblies provided the homogeneity of the remanufacture process has been retained throughout the inspection lot.“ “4.2.1.2 Size of lot. A lot shall consist
9、of an identifiable group of * 4.2.2, 1 ine 2, change “ASA 846.1“ to “ANSI B46.1-78“. 4.2.2, add to the end of the paragraph, “Ring, Tube, Stop P/N D8593673 shall be visually examined 100% for groove at internal threaded end. Rings without groove shall be modified and reprocessed. PAGE 6 4.2.2.3, del
10、ete C.D. 101“ in its entirety. PAGE 7 4.2.2.5, delete C.D. “102“ in its entirety. PAGE 8 4.2.2.6, delete C.D. Ii1O4“ in its entirety delete C.D. “105“ in its entirety and substitute “105. delete C.D. “204“ in its entirety and substitute “204. Depth of Depth of internal thread cavity, min., . . . Gag
11、e“, internal thread cavity, max., . . . Gage“. c 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-60683 (2) 13 7777906 0340874 1 i! MIL-C-60683( OS) AMENDMENT 2 15 JULY 1986 PAGE 9 4.2.2.8, delete C.C. “102“ in its entirety. PAGE 10 4.2.2.10,
12、delete C.D. 102“ in its entirety. PAGE 11 4.2.2.12, delete C.D. ii102i in its entirety. PAGE 12 4.2.2.14, delete C.D. 11102“ in its entirety. 4.2.2.16, delete C.D. “102“ in its entirety. PAGE 13 4.2.2.17, delete C.D. “102“ in its entirety. * marked with an asterisk to indicate where changes (additio
13、ns, modifications, corrections, deletions) from the previous issue were made. This was done as a convenience only, and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on
14、the entire content irrespective of the marginal notations and relationship to the last previous i ssue. Changes from previous issue. The margins of this specification are Preparing Activity: Navy - OS Project No. 1377-N822 f7U.S. GOVERNMENT PRINTING OFFICE 1988 - 806-038/44133 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
