1、MIL-D-L8300H m 9999906 L644593 3ib 23 February 1993 SUPRSEDING ,MIL-D-l8300G(AS “. - 1 March 1970 MILITARY SPECIFICATION DESIGN EXAMINATIONS, ENGINEERING AVIONIC SYSTEMS/EQlJIPMENT GENERAL REQUIREMENTS FOR This specification is approved for use by the Naval Air Systems Command, Department of the Nav
2、y and i S avai lable for use by al 1 Departments and Agencies of the Department of defense. 1. SCOPE 1.1 Data. This specification covers the preparation of data for the General Requirements for Design Examinations, Engineering Avionic SystemslEquipment in support.of Naval Air Systems Command (NAVAIR
3、) avionics design, development, test, production and installation, for aircraft weapon systems. This specification does not cover financial or adminfstrative data nor development, manufacturing or test facilities data nor evaluation, operational or material support data. (See 6.1 for intended use.)
4、1.2 Types of data. This specification covers the preparation of all types of engineering data generated during thevalidation or advanced develop: contracting. Some types of data covered may also be generated on contracts let during the conceptual and operational phases of the program. -Figure 1 show
5、s the applicability of types of technical data to various phases of a program. ment, the full scale development and the production phases of equipment 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifi- cations, standards, and hand
6、books form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifica- tions and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Benefi
7、cial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Air Systems Command, Attn: Avionic and Computer Resources Division (AIR-546), Washington, DC 20361-5460, by using the self-addressed St
8、andardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N6895 FSC 58GP DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
9、om IHS-,-,-SPECIFICATIONS MILITARY MIL-E-5400 MIL-E-605 MIL-C-678 MIL-9-9858 MI L-T-1 8303 MIL-N-18307 MIL-T-23103 MIL-1-31000 MI L-M-3876 1 MIL-1-45208 MIL-H-46855 MI L-M-8 MI L-D-8 1927 1992 Electronic Equipment, Airborne, General Spec- ification for Electromagnetic Compatibility Requirements, Sys
10、 tems Control Panel: Aircraft Equipment, Rack or Console Mounted Quality Program Requirements Format for Preproduction, Acceptance and Life for Aircraft Electronic Equipment Test Procedures Nomenclature and Identification for Aeronautical Systems including Joint Electronics Type Designated Systems a
11、nd Associated Support Systems General Requirement for Thermal Performance Evaluation, Airborne Electronic Equipment and Sys tems General Specification for Technical Data Packages General Requirements for Preparation of Microfilming and Photographing of Engineering/ Technical Data and Related Documen
12、ts: PCAM Card Preparation, Engineering Data Micro-reproduction System Inspection System Requirements Human Engineering Requirements for Military Systems, Equipment and Facilities General Style and Format of Technical Manua (Work Package Concept 1 Preparation of lechnical Directives MIL-M-85337 Requi
13、 rernents Technical for Manua Assurance Program 2 1: Quality 1s Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDS MI LI TARY MIL-STD-100 MIL-STD-449 MIL-STD-461 MIL-STO-462 MIL-STD-469 MI L-STO-470 MI L-STD-47 1 MI L-STD-490 MIL-STD-499 MIL-S
14、TD-680 MIL-STD-756 MIL-STD-781 MIL-STD-785 MI L-STD-81 O Engineer i ng Drayi ng Practices Radio Frequency Spectrum Characteristics Measurement of, Electromagnetic Emission and Suscepti bi 1 i ty Requirements for the Control of Electr,omagnetic Interference Electromagnetic Interference Characteristic
15、s, Measurement of Radar Engineering Design Requirements, Electro- magnetic Compatibility Mainta,inability Program for Systems and Equipment Maintainability Verifi,cation/Demonstration/ Evaluation Specification- Practices Engineering Management Standardization Program Requirements for Defense Acquisi
16、tions Reliability Modeling and Prediction i Reliability Testing for Engineering Development, Qualification, and Production Reliability Program for Systems and Equipment Development and Production Environmental Test Methods and Engineering Gui del i nes 3 Provided by IHSNot for ResaleNo reproduction
17、or networking permitted without license from IHS-,-,-, STANDARDS . MrLITARY MIL-STD-831 MIL-STD-881 MI L-STD-882 MIL-STD-961 MIL-STD-962 MIL-STD-965 MIL-STD-970 MIL-STD-973 MI L-STD- 1 52 1 MI L-STD- 1 528 MI L-STO- 1556 MIL-STD-1629 MIL-STD-2069 MI L-STO-2072 MIL-STD-2084 MIL-STO-2096 MIL-STD-2097
18、DOD-STD-2 1 67 MIL-STD-45662 - . “ - “ MIL-D-LB3OOH W 999990b l64V59b OT5 MI L-D- 1 8300H (AS) Test Reports, Preparation of Work Breakdown Structures for Defense Materiel I tems System Safety Program Requirements Military Specification and Associated Documents, Preparation of Military Standards, Han
19、dbooks, and Bulletins, Preparation of Parts Control Program Standards and Specifications, Order of Preference for the Selection of Configuration Management Technical Reviews and Audits for Systems, Equip- ments, and Computer Software Manufacturing Management Program GovernmentlIndustry Data Exchange
20、 Program (GIDEP) Contractor Participation Requirements Procedures for Performing a Fai 1 ur-e Mode, Effects and Criticality Analysis Requirements for Aircraft Nonnuclear Sur- vivability Program Survivability, Aircraft; Establishment and Conduct of Programs for General Requirements.for Maintainabilit
21、y of L Avionic and Electronic Systems and Equipment Microcircuit Data Requirements Acquisition of Support Equipment and Associated Integrated Logistics Support Defense System Software Development Calibration Systems Requirements 4 Provided by IHSNot for ResaleNo reproduction or networking permitted
22、without license from IHS-,-,-HANDBOOKS MILITARY MIL-HDBK-237 .Electromagnetic Compatibility Management Guide: for Platforms, Systems and Equipment BULLETIN MI L-BUL-544 Federal /Mi 1 i tarylIndustry Specifications and Standards, and NAVAIR Series Documents Approved by the Naval Air Systems Command (
23、Unless otherwise indicated, copies of federal and military specifica- tions, standards, and handbooks are avallable frm the DODSSP Standardization Documents Order Desk, 700 Robbins Avenue, Building 40, Philadelphia., PA 191 11-5094.) 2.1.2 Other Government documents, drawinqs, and publications. The:
24、 fol lowing other Government documents , drawings, and pub1 i cations form d part of this document to the extent specified herein. Unless o,t.herwise specified, the issues are those cited in the. solicitation. NAVAL AIR SYSTEMS COMMAND (NAVAIR) EI-1000 Avionics Installation Instruction, Format for E
25、T-1000 Avionics Bench, Pre-Flight and Flight Test Instruc-. tion, Format for AD- 1 350 Engineering Dt-awings and Associated Data AR-29 AR-30 AR-41 Frequency Allocation and Equipment Spectrum Signature Requirements for Integrated Logistic Support Requirements for Aero- nautical. Systems and Equipment
26、 Technical Directive Development and Acquisition of Integrated Logistic Support for Aeronautical Weapon System Change,s AV-2000 Format for PreDaration of Military Specifications General Requirements for Av AV-4000 0utli.ne for Preparation of M for Ground Support Equipment on i c qui pme ilitary Spec
27、 nt ifications 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NAVAL AIR SYSTEMS COMMAND (,NAVAIR) (continued) AV-5000 Outline for Preparation of Military Specifications for Aircraft Instruments Explanation AV- 1 O000 Format for Naval Air Systems C
28、ommand Avionic System Performance Specifications for Weapon Systems AV- 1 O00 1 Format for Naval Air Systems Command Avionics Installation/Interface/Test Specifications for Weapon Sys tems SD 8706 Design Examinations, Engineering, Aircraft Weapon Systems, General Specification for (Copies of NAVAIR
29、specifications, publications, and drawings may be obtained upon.application to the Contracting Officer, Naval Air Systems Command, Navy Department, Washington, DC 20361-5460.) 2.2 Non-Government publications. The following document forms a part of this document to the extent saecified herein. Unless
30、 otherwise specified, the issues of the docments which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN NAT
31、IONAL STANDARDS INSTITUTE (ANSI) ANSI ( APP Standards 2.3 z 39 .la Information Sciences - Scientific and Techni cal Reports, Organization, Preparation and Production of lication for copies should be addressed to the American National Institute, 1430 Broadway, New York, NY 10018-3308.) Order of prece
32、dence. In the event af a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothi ng. in thi s document, however, supersedes appi i cable daws and regulations unless a specific exemption has been obtained. 2.3.1 Utilization of spec
33、ifications, standards, drawings and publica- tions. 2.3.1.1 Supplementary documents. In addition to the referenced docu- ments, other specifications, standards, handbooks, drawings.,. and publicati.ons may be required for design, deve,lopment, pfoducti-on and utilization of the data being specified,
34、 in which case appropriate doc:uments should be selected from MIL-BUL-544 and may be used without further approval if they :do, not require tailoring to the program. When appropriate documents cannot be . selected from MIL-BUL-544, they shall be selected from DODISS in accordance with MIL-STD-970 an
35、d referred to the contracting activity for. approval. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-LB300H W 9999906 L844599 804 W Justifications for use and tailoring of the documents with supporting evidence of their sui tabi li ty shall
36、be included with the request for approval of the documents. 2.3.2 Utilization of approved documents. Specified information content, accuracy and clarity of data prepared under this specification is the responsjbility of the contractor.and the use of specifications, standards, handbooks, drawings and
37、 pub1 ications 1 isted or approved by the contracting activity is in no way to be considered as a guarantee of the acceptance of the end product. 2.3.3 Formal approval of documents. To prevent the proliferation of documents and enhance standardization, formal approval of non-approved documents is re
38、quired by the contracting activity. Submission of non-approved documents to the contracting activity in accordance with contractual require- ments does not constitute approval until the contractor has been notified of the acceptability of the documents for use on the contract. On subsequent orders f
39、or the same type of data, the contractor shall consider all documents approved for use on the precedingcontract or the latest revision of these documents to be approved for use on the current contract unless notified to the contrary by the contracting activity. 3. REQUIREMENTS 3.1 General. The tasks
40、 and work required to generate the data covered by this specification shall be in accordance with the applicable equipment or weapon system specifications, the statement of work (SOW) and the contract. The data shall be edited and formatted in accordance with this specification and applicable Data I
41、tem Descriptions (DID) (DD Form 1664) and submitted and delivered in accordance with the Contract Data Requirements List (CDRL) (DD Form 1423) and the contract. 3.1.1 Data formats. All data shall be prepared in the formats specified in this specification or the referenced specifications. Scientific
42、and technical reports shall be in accordance with ANSI Z 39.18. Test procedures shall be in accordance with MIL-T-18303. Test reports shall be in accordance with MIL-STD-831. Specifications shall be in accordance with MIL-STD-961 and standards and handbooks shall be in accordance with MIL-STD-962. D
43、rawings shall be in accordance with AD-1350 and MIL-STD-100. Technical directives shall be in accordance with MIL-D-81992. Technical manuals shall be in accordance with MIL-M-81927. Contractor and computerized formats will be acceptable alternatives when authorized by the contracting activity. 3.1.2
44、 Tasks, work and data. Engineering data is generated by tasks and work in all areas of manaqement except Data Management as shown in table I, Summary Work Breakdown Sthcture CSWBS) for an Avionic SystemlConfiguration Item (see 6.4). For contracting activity management and equipment deployment and ut
45、ilization, it is not necessary that all data generated by tasks and work on the contract be formalized or delivered. The contracting activity will review the specifications, the SOW, which includes the SWBS, and the contract requirements and select only those data items necessary to manage the contr
46、act and utilize the equipment. This specification covers all general engineering 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-data for typical avionic equipment and will be tailored for a specific contract by changing +the requirements for-speci
47、fied data and adding and del et i ng data i tems . a - 3.2 Management data. The contractor shall prepare the following data for engineering management of the project. 3.2.1 Contract work breakdown structure (CWBS). The SWBS shall be extended to levels which provide specification requirements and con
48、figuration control visibility. MIL-STD-881 .shall be used as a guide in extending the SWBS into a CWBS. 3.2.2 Data schedule and receipts. The contractor shall index the data and prepare contract data status and schedule report for all data items ordered by the contracting activity. 3.2.3 Government
49、furnished equipment (GFE) manaqement and control. The contractor shaTl provide .a, dqscription of his GFE management and control system and prepare reports on scheduling, maintaining, accounting for and disposing of GFE. 3.2.4 Techniral review and audit datai for each review and adit required by the contract, the contractor shall issue an aqenda, DreBare package and prepare and .issue the minutes of the meetings-using M
