1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/5E(SH) 26 April 2013 SUPERSEDING MIL-C-24231/5D(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTORS, SINGLE CABLE, TYPE III, THREE-, FOUR-, OR FIVE-CONDUCTOR This specification is approved for use by the Naval Sea Systems Command and is available for use
2、by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Dimensions and configuration: see figures 1 through 18. 2. The gland nut shall be tightened until th
3、e packing tightens against the wires. This can be determined by moving the wires gently back and forth until the wire is seized by the packing. The gland nut shall be turned approximately one-fourth of a turn more to hold the wires in place. Do not overtighten the gland nut or attempt to tighten dow
4、n metal to metal, as this can damage the wires. 3. Full or partial threads shall not extend more than 0.063 inch beyond the -inch thread length. 4. The alternate method of installing the guide pin (see figure 3) eliminates the need for welding in the fabrication of a single cable connector body. 5.
5、Retainer plate, packing, and retainer plate assembly for other special conductor arrangements (for example, LS2SWU-1 and MIL-DTL-16878/36 BJE0 wire combinations) shall meet the following requirements: a. Where LS2SWU-1 cable is required, the hole size shall be 1764 diameter. b. Positional tolerancin
6、g for all holes shall be . c. Holes shall not be located closer than 0.010 from the minimum gland nut inside diameter of part number M24231/5-072 and the retainer plate position pin holes of part number M24231/5-050. d. Minimum material between holes shall be 0.031. e. Protective sleeving shall be s
7、ized to suit the number of cables required where use of the specified sleeving, item 24, is inadequate. 6. The retainer plates and the retainer plate assemblies shall be manufactured from nickel-copper alloy in accordance with Class A, Form 1, hot-finished condition of QQ-N-281 with a minimum yield
8、strength of 40,000 lbf/in2 at 0.2 percent offset, or nickel-copper alloy in accordance with Class A, Form 1, cold-drawn condition of QQ-N-281 with a minimum yield strength of 50,000 lbf/in2 at 0.2 percent offset. 7. Welding of the pin (/5-071) is allowed after the hull fitting body has been age-hard
9、ened to achieve its required physical properties. 8. Unless otherwise specified (see figure 17), all dimensions are in inches. FIGURE 3. Plug sleeve - M24231/3-010.5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/5E(SH) 2 9. Tolerances
10、shall be as follows, or as stated: a. Decimals 0.005 inch. b. Fractions 164 inch. c. Angular dimensions degree. 10. The flange outside diameter is intended to coincide with commonly available 2-inch bar stock. The dimension may vary after machine clean-up. Provided by IHSNot for ResaleNo reproductio
11、n or networking permitted without license from IHS-,-,-MIL-DTL-24231/5E(SH) 3 FIGURE 1. Connector, single cable typical. 224221411121034 35 3681618171564231231315727202119252932302831SLEE VING, M2423 1/ 5- 01 1HARDNE SS REA DING TO BE TAKEN A T THESE P OI NT S.HARDNE SS REA DING TO BE TAKEN A T THIS
12、 F AC E AT1 20-DE GREE INTERV AL S.1WASH ER,M2423 1/5- 07 5GAS KET ,O- RING,SAE- AS287 75 - 32 7PLA TE, RE T(SEE PAR TS LIS T)PIN, NI- CU,M24 231/5- 07 1FOR ALT MT HD O FINSTALLING PIN ,SEE FIG. 3.IDENT PLA TE ,M2423 1/5-081, M24 231/5 - 08 2,see figure 1. 5 Gasket, O-ring 1 1 1 SAE-AS28775-329 See
13、item 4. 6 Gasket, O-ring 1 1 1 SAE-AS28775-115 See item 4. 7 Gasket, O-ring 1 1 1 SAE-AS28775-327 See item 4. 8 Body, single cable connector 1 1 1 Ni-Cu-Al, Class A, QQ-N-286 See figure 2 and continuation of figure 2. 9 Pin, contact 3 4 5 MIL-DTL-24231 See figure 17. 10 Assembly, plate, retainer 1 S
14、ee items 26 and 33 See figure 6 and requirement 6. 11 Assembly, plate, retainer 1 See items 26 and 31 See figure 11 and requirement 6. 12 Assembly, plate, retainer 1 See items 26 and 32 See figure 15 and requirement 6. 13 Nut, gland 1 1 1 Ni-Al-BRZ, ASTM B150/B150M See figure 8 and requirement 2. 14
15、 Nut, body 1 1 1 Ni-Cu-Al, QQ-N-286 See figure 7. 15 Washer, body, 3.5 od by 1.760 id by 0.162 thick 1 1 1 Ni-Cu-Al, QQ-N-286 See figure 1, finish shall be 63 microinches. 16 Insert assembly, molded 1 See items 09, 37, and 38 See figure 17. 17 Insert assembly, molded 1 See items 09, 37, and 38 See f
16、igure 18. 18 Insert assembly, molded 1 See items 09, 37, and 38 See figure 16. 19 Insert, 0.1250.002 diameter, lg to suit 1 1 1 Nylon, Group I, Class I, ASTM D4066 See figure 1. 20 Screw, 0.138-32 by 316 lg RHMS 2 2 2 CRES, coml See figure 1. 21 Ring, retaining 1 1 1 SPIROLOX, PRD-99-M, or equal See
17、 figure 1, M24231/5-073. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/5E(SH) 20 TABLE I. Parts list Continued. Item no. 1/ Description 2/ Quantity for M24231/5- 3/ Material/specification Remarks 001 002 003 22 Ring, retaining 1 1 1 T
18、RUARC, Type 5100-162-W, or equal See figure 1, M24231/5-076. 23 Cap, pressure-proof 1 1 1 M24231/12-011 See figure 1. 24 Sleeving, 0.360 id by 0.020 thick 14 14 14 Type F, Form U, Category 1, color clear, MIL-I-631 See figure 1. 25 Pin, guide, 0.092 diameter, lg to suit 1 1 1 Ni-Cu, Class A, QQ-N-28
19、1 See figure 1 and figure 3 and requirements 4 and 7. 26 Pin, positioning 1 1 1 Ni-Cu, Class A, QQ-N-281 See figure 6, figure 11, and figure 15. 27 Plate, identification, 116 thick 1 1 1 CRES or Al, Type 1, MIL-DTL-15024 See figure 12. 28 Plate, retainer 1 Ni-Cu, Class A, QQ-N-281 See figure 4 and r
20、equirement 6. 29 Plate, retainer 1 Ni-Cu, Class A, QQ-N-281 See figure 9 and requirement 6. 30 Plate, retainer 1 Ni-Cu, Class A, QQ-N-281 See figure 13 and requirement 6. 31 Plate, retainer 1 Ni-Cu, Class A, QQ-N-281 See figure 11 and requirement 6. 32 Plate, retainer 1 Ni-Cu, Class A, QQ-N-281 See
21、figure 15 and requirement 6. 33 Plate, retainer 1 Ni-Cu, Class A, QQ-N-281 See figure 6 and requirement 6. 34 Packing, durometer 555 1 Rubber, ZZ-R-768 See figure 5. 35 Packing, durometer 555 1 Rubber, ZZ-R-768 See figure 10. 36 Packing, durometer 555 1 Rubber, ZZ-R-768 See figure 14. 37 Wire, 151”
22、3 4 5 MIL- DTL-16878/36 BJE0 See figure 17. 38 Epoxy resin, molded As required Cast epoxy resin comp 4/ See figure 16, figure 17, and figure 18. NOTES: 1/ Item numbers are the same as encircled numbers shown on figures. 2/ See applicable figure or table listed in remarks column for part numbers and
23、dimensions. 3/ Quantity is for one complete assembly of each size. 4/ Arco Set 200, M.M. Reif and Co., Ivyland, PA, or PR610-TCF (Chockfast Orange), ITW Philadelphia Resins Corp., Montgomeryville, PA, or equal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
24、 IHS-,-,-MIL-DTL-24231/5E(SH) 21 CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing activity: Navy SH (Project 5935-2011-054) NOTE: The activities listed above were intereste
25、d in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
