1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/6F(SH) 26 April 2013 SUPERSEDING MIL-C-24231/6E(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTOR, SINGLE CABLE, TYPE III, FOR DSS-3 CABLE This specification is approved for use by the Naval Sea Systems Command and is available for use by all Departments
2、 and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Dimensions and configuration: see figures 1 through 7. 2. Full or partial threads shall not extend more than 0.083 inc
3、h beyond the 916-inch thread length. 3. Refer to MIL-DTL-24231/5 for alternate method of manufacturing connector body and installing guide pin M24231/5-071. 4. For welding of the pin, item 17, see MIL-DTL-24231/5. 5. All dimensions are in inches. 6. Tolerances shall be as follows, or as stated: a. D
4、ecimals 0.005 inch. b. Fractions 164 inch. c. Angular dimensions degree. d. Tolerances for rubber packing should follow the guidance provided in table XLI (RMA Drawing Designation A2 Precision) of MIL-HDBK-149. 7. The flange outside diameter is intended to coincide with commonly available 2-inch bar
5、 stock. The dimension may vary after machine clean-up. 8. The gland nut shall be tightened until the packing tightens against the wires and cables. This can be determined by moving the wires and cables gently back and forth until the wire and cable is seized by the packing. The gland nut shall be tu
6、rned approximately one-fourth of a turn more to hold wires and cables in place. Do not overtighten the gland nut or attempt to tighten down metal to metal, as this can damage the wires and cables. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D
7、TL-24231/6F(SH) 2 FIGURE 1. Connector, single cable M24231/6-001, symbol no. 517.4. HARDNE SS REA DING TO BE TAKEN A T THESE P OI NT S.HARDNE SS REA DING TO BE TAKEN A T THIS F AC E AT1 20-DE GREE INTERV AL S.2CABLE DSS - 31 5 FEE T L ON G.NUT, GLANDM2423 1/6- 01 1PIN, M2 4231 /5 - 07 1SEE RE QT 3 A
8、ND 4.PLATE, ID EN TM2423 1/6- 03 1FIGURE 1. Con ne ctor, sing le cab le M2423 1/6-001 , symbol no. 517.4.SCREW,M2423 1/5- 08 3INSER T,M2423 1/5- 07 7RING, RETA ININGM2423 1/5- 07 6WASH ER, SPRING LOCKNAS M35 3 38 -124RING, GLAN DM2423 1/6- 01 3NUT, M2 4231 /5 - 07 4WASH ER, M2423 1/5- 07 5GASK ET, O
9、 RINGSAE- AS287 75 - 32 7PACK ING, M2 4231 /6 - 01 2ASSY , SINGL E CON NECTOR BO DY ,M2423 1/6- 01 0ASSY , INSERT, MOLDEDM2423 1/6- 02 0GASK ET, O- RINGSAE- AS287 75 - 32 9GASK ET, O- RINGSAE- AS287 75 - 11 5RING, RETA ININGM2423 1/5- 07 3CAP, M242 31/12 - 01 1GASK ET, O- RINGSAE- AS287 75 - 21 522
10、2211111591312411610358721920181714161 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/6F(SH) 3 63320.8970.8871.5551.5451.6301.6201.7501.7452.0051.995125ALL OVER EXCEPTAS SHOW N.63* PIN, WELD .SEE REQT 3.* 0.0510.0411-1 2UNF-2 BSEE REQT
11、2.0.0720.0680.1900.180RFIG URE 2. As se mbly , si ngle c able c onnecto r b od y - M 24 23 1/6 -01 0 . 629322.2242.2141.688-12 UN - 2 A3169161582.2242.214635.8805.8707320.5050.4950.4420.432133272332132R0.120 H OLE ,0.187 D EEP, D ONOT PE NET RAT E.+0. 00 0-0. 00 5320.9890.9790.5300.5001.750-12 UN -
12、2 A0.0590.049R18UNDERCUT.15160.8760.87263116R3018300.0670.0570.0270.0230.8960.8861.0921.088321.3021.298234, SEE NO TE 3.30320.0660.0620.7860.776*18*0.0510.041FIGURE 2. Assembly, single cable connector body M24231/6-010. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without l
13、icense from IHS-,-,-MIL-DTL-24231/6F(SH) 4 R964R0.138-32NC -2B, 2 H OL ES , 316D EEP.(LO CATE TO SUIT IDE N T IF IC AT IO N P LA T E. )FIGURE 2. Assembly, si ngle cable connector body - M 24231/6- 010 - conti nued .0.0520.0506FIGURE 2. Assembly, single cable connector body M24231/6-010 Continued. 6
14、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/6F(SH) 5 FIGURE 3 . Pla te, identific ation - M 24 23 1/6 -03 1 . 180.156, 2 HOLES51658CURRENT REV. LE T T ER A TTIME O F MANU F AC T U R E.18H IGH LTRS (MI N) .3163MANUFACTUR ER SIDENTIFI
15、C AT IO NHULL H OLE NO.REVM24 231/6-00 1138R116FIGURE 3. Plate, identification - M24231/6-031. 18 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/6F(SH) 6 FIG U R E 4. A ss emb ly , ins ert , molded - M2 42 31 /6- 02 0 . 10213CL0.7 140.
16、7 1015 FEETCA BL E, DSS -3MOL DED EPOXY RESINSOLDE R TO P INS.164R1161332+132-132149640.0 580.0 4838141.5 051.4 950.0 600.0 50RGRO OVE0.6 300.6 20PIN , CONT ACT(3 RE QUIRED)0.8 650.8 550.1 400.1 30(TYP)0.0 820.0 720.1 610.1 51222321CLFIGURE 4. Assembly, insert, molded - M24231/6-020. 10 Provided by
17、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/6F(SH) 7 FIG U R E 5. P ac ki ng - M 2423 1/6 -01 2 . 110 .87 50 .49 01.0 00MOL D OR M ARK WITH INDELI BLE INKTHE PAR T NO. ON THIS SU RFACE.FIGURE 5. Packing - M24231/6-012. FIG U R E 6. N ut, gl and
18、 - M 2423 1/6 -01 1 . 160.5 200.5 101-1 2U NF-2A3163163418R11863ALL O VER.FIGURE 6. Nut, gland M24231/6-011. 11 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/6F(SH) 8 FIGURE 7. Ring, gland M24231/6-013. FIG U R E 7. R ing, gl and -
19、 M 24 23 1/6 -01 3 . 147818164X 45 CH AM FER336414 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/6F(SH) 9 TABLE I. Parts list. Item no. 1/ Description 2/ Quantity for M24231/6- 3/ Material/specification Remarks 001 1 Connector assembl
20、y, single cable, symbol no. 517.4 1 - See figure 1. 2 Gasket, O-ring 1 SAE-AS28775-215 Lubricate with silicone compound SAE-AS8660, see figure 1. 3 Gasket, O-ring 1 SAE-AS28775-329 See item 2. 4 Gasket, O-ring 1 SAE-AS28775-327 See item 2. 5 Gasket, O-ring 1 SAE-AS28775-115 See item 2. 6 Single cabl
21、e connector body 1 Ni-Cu-Al, QQ-N-286 See figure 2 and continuation of figure 2. 7 Cap, pressure-proof 1 MIL-DTL-24231/12-011 See figure 1. 8 Ring, retaining 1 M24231/5-073 See figure 1. 9 Ring, retaining 1 M24231/5-076 See figure 1. 10 Insert assembly, molded 1 See items 21, 22, and 23 See figure 4
22、 11 Packing, Class A, durometer, 555 1 Rubber, ZZ-R-768 See figure 5. 12 Washer, body 1 M24231/5-075 See figure 1. 13 Nut, body 1 M24231/5-074 See figure 1. 14 Ring, gland 1 Ni-Al-BRZ, ASTM B150/B150M See figure 7. 15 Washer, spring lock 1 NASM35338-124 See figure 1. 16 Nut, gland 1 Ni-Al-BRZ, ASTM
23、 B150/B150M See figure 6. 17 Pin, guide 1 M24231/5-071 See figure 1. 18 Plate, identification, 116 thick 1 CRES or Al, MIL-DTL-15024 See figure 3. 19 Insert 1 M24231/5-077 See figure 1. 20 Screw 2 M24231/5-083 See figure 1. 21 Pin, contact 3 MIL-DTL-24231 See figure 4. 22 Cable, DSS-3, 15 1 MIL-DTL-
24、915/8 See figure 1 and figure 4. 23 Epoxy resin, molded As required Cast epoxy resin compound 4/ See figure 4. NOTES: 1/ Item numbers are the same as encircled numbers shown on figures. 2/ See applicable figure or table listed in remarks column for part numbers and dimensions. 3/ Quantity is for one
25、 complete assembly of each size. 4/ Arco Set 200, M.M. Reif and Co., Ivyland, PA, or PR610-TCF (Chockfast Orange), ITW Philadelphia Resins Corp., Montgomeryville, PA, or equal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/6F(SH) 10 C
26、HANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing activity: Navy SH (Project 5935-2011-055) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
