1、AMSC N/A FSC 4810 METRIC MIL-DTL-24695/2B(SH) 25 September 2012 SUPERSEDING MIL-V-24695/2A(SH) 23 December 1991 DETAIL SPECIFICATION SHEET VENT AND TEST VALVE HOSE ASSEMBLY HYDRAULIC SERVICE This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is avail
2、able for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24695. The detail of vent and test valve hose assembly end fitting is provided on figure 1. Provided by IHSNot
3、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24695/2B(SH) 2 L2.3(0.091)F IGUR E 1. De ta il o f v en t v alve fit ting .12 mm X 1.5 R EVER SE BUT TR ES S IN TE RN ALTHREADS (BOTH ENDS ) S E E N O T E 2KNUR L T O S UIT H AN DIN STAL LATI ON (BOT H EN DS )HOSE
4、 END PLUG (BO TH E N D S )18.0(0.709)MAX .2.5(0.098)3.3 0 ( 0. 13 0)3.2 4 ( 0. 12 8)608.0 (0.315)7.7 (0.304)14.55(0.573)1.0 ( 0.0 39) MI NI MU MIN TER NAL DI A. A FT ERSWAGE WITH 0.5 X 0 .5(0 .02 X 0.02) SL OTACRO SS DI A. AS S HO W NFIGURE 1. Detail of vent and test valve hose assembly end fitting.
5、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24695/2B(SH) 3 NOTES: 1. Dimensions in millimeters (and inches). 2. Reverse (compression) buttress threads shall be as specified herein and as shown on the vent and test valve configuration of
6、MIL-DTL-24695/1 for the cap or internal threads. Hose End Fitting thread: Major dia.: 12.605 - 12.715 (internal) Pitch dia.: 11.915 - 12.025 Minor dia.: 11.375 - 11.485 3. Materials shall be in accordance with MIL-DTL-24695 (see requirement 3 below). 4. Tolerances 0.2 millimeter (0.008 inch) except
7、as noted. 5. Hose length tolerance: 12 millimeters (0.47 inch). FIGURE 1. Detail of vent and test valve hose assembly end fitting Continued. REQUIREMENTS: 1. Torque required to connect the hose assembly to the vent and test valve shall be in accordance with MIL-DTL-24695. 2. Hose ends shall be prote
8、cted by plugs to prevent thread damage and dirt infiltration in accordance with NAS847. 3. Part number: The part number shall consist of the basic number of this specification sheet plus a dash number indicating hose length (see table I) and “A” for NiCu alloy or “C” for CRES pressure containing par
9、ts. Example: M24695/2-03-C - 915 millimeter (3 feet) hose assembly with CRES pressure containing parts. M24695/2-10-A - 3050 millimeter (10 feet) hose assembly with NiCu alloy pressure containing parts. TABLE I. Dash numbers indicating hose length. Dash no. L millimeters required feet reference only
10、 -01 305 1 -03 915 3 -06 1830 6 -10 3050 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24695/2B(SH) 4 CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue du
11、e to the extent of the changes. Preparing Activity: Navy SH (Project 4810-2012-003) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
