1、 DETAIL SPECIFICATION ANTI-G GARMENT, CSU-15A/P This specification is approved for use by the Naval Air Systems Command, Department of the Navy and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the detail requirements
2、 and inspections for the anti-gravity (anti-G) garment, CSU-15A/P, worn by U.S. Navy and U.S. Marine Corps aviators of high performance aircraft. 1.2 Classification. The anti-G garment, CSU-15A/P furnished under this specification will be of the following types and the following sizes (see 6.2). Cla
3、ss I Sage Green 3734 Class II Khaki P-1 3729 Small regular Medium regular Large regular Large extra long Small long Medium long Large long 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 or 4 of this specification. This section does not include d
4、ocuments cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 or 4
5、 of this specification, whether or not they are listed. Comments, suggestions, or questions on this document should be addressed to the Commander Naval Air Warfare Center Aircraft Division, Code 4L8000B120-3, Highway 547, Lakehurst, NJ 08733-5100 or emailed to michael.sikoranavy.mil. Since contact i
6、nformation can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.dla.mil. AMSC N/A FSC 8475INCH-POUND MIL-DTL-81905G(AS) 04 November 2013 SUPERSEDING MIL-DTL-81905F(AS) 07 April 2010 Provided by IHSNot for ResaleNo reproduction
7、or networking permitted without license from IHS-,-,-MIL-DTL-81905G(AS) 2 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issu
8、es of these documents are those cited in the solicitation or contract. FEDERAL STANDARDS FED-STD-4 - Glossary of Fabric Imperfections FED-STD-595/27040 - Miscellaneous, Semi-gloss FED-STD-595/37038 - Miscellaneous, Flat or Luster FED-STD-595/37056 - Miscellaneous, Flat or Luster FED-STD-595/34096 -
9、Green, Flat or Luster FED-STD-595/34097 - Green, Flat or Luster FED-STD-595/34128 - Green, Flat or Luster COMMERCIAL ITEM DESCRIPTIONS (CIDS) A-A-50195 - Thread, Aramid A-A-55126 - Fastener Tapes, Hook and Loop, Synthetic A-A-55634 - Zippers (Fasteners, Slide Interlocking) A-A-55809 - Insulation Tap
10、e, Electrical, 600V Polyvinyl Chloride, Pressure-Sensitive Adhesive A-A-59826 - Thread, Nylon DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-5038 - Tape, Textile and Webbing, Textile, Reinforcing, Nylon MIL-W-5664 Webbing, Textile, Elastic MIL-PRF-6855 - Rubber, Synthetic, Sheets, Strips, Molded or Ex
11、truded Shapes, General Specification For MIL-DTL-32075 - Label; for Clothing, Equipage, and Tentage, (General Use) MIL-DTL-32092 - Leather, Cattlehide, Deerskin, and Horseshide, Chrome Tanned MIL-T-38328 - Tape, Textile, Nylon, Aromatic, Non-Melting, Reinforcing MIL-C-43204 - Cloth, Spacer (Olefin)
12、MIL-L-43283 - Leather, Calfskin, Kip, and Cattlehide for Footwear Uppers, Chrome Tanned MIL-W-81116 - Webbing, Textile, Polyamide, High Temperature Resistant, Loop Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-81905G(AS) 3 MIL-C-83242 - Cor
13、d, Aromatic Polyamide, Non-Melting (Inactive for new design) MIL-C-83390 - Connector, Hose, Quick-Acting, Male, Anti-G Garment (Inactive) MIL-C-83489 - Cloth, Coated, Nylon, Polyurethane Coated MS27755 - Connector, Hose Quick Disconnect, Female, Anti-G Suit (Copies of these documents are available o
14、nline at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following drawings form a part of this document to the extent
15、specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. NAVAL AIR SYSTEMS COMMAND DRAWINGS 1628AS100 - Top Assembly Drawing, Anti-g Garment CSU-15A/P 1628AS900 - Spacer, Tube Anti-g Garment, CSU-15A/P 3926AS100 - Fasteners, Slide,
16、Anti-g Garment NAVY CLOTHING AND TEXTILE RESEARCH FACILITY PURCHASE DESCRIPTION NCTRF PD-01-10 - Cloth, Plain and Basket Weave, Aramid U.S. AIR FORCE DRAWING 74204 - Spacer, Tube Anti-G Garment (Copies of this document are available from Defense Supply Center Philadelphia, Clothing and Textiles Dire
17、ctorate, Attn: DSCP-CBTC, (Bldg 6), 700 Robbins Ave., Philadelphia, PA 19111-5092.) CODE OF FEDERAL REGULATION 14 CFR - Part 25Aeronautics and Space Defense Federal Acquisition Regulation Supplement, Clause 252.211-7009 (Copies of these documents are available online at http:/www.gpo.gov or from the
18、 Government Printing Office, 732 North Capitol Street NW, Washington, DC 20401-0001.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-81905G(AS) 4 2.3 Non-Government publications. The following documents form a part of this document to the ex
19、tent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS AATCC Test Method 135 - Dimensional Changes in Automatic Home Laundering of Woven and Knit Fabrics (Copies of this
20、document are available online at http:/www.aatcc.org or AATCC P.O. Box 12215, Research Triangle Park, North Carolina 27709-2215.) AEROSPACE INDUSTRIES ASSOCIATION (AIA) NAS397 - Clamp-Ratchet, One Piece (DoD adopted) NASM20230 - Grommets, Metallic, Plain and Spur, With Washers, Type I and Type III.
21、(DoD adopted) NASM27980 - Fastener, Snap, Style 2 (Regular Wire Spring Clamp Type). (DoD adopted) (Copies of these documents are available online at http:/www.aia-aerospace.org or from the Aerospace Industries Association, 1000 Wilson Blvd., Suite1700, Arlington, VA 22209-3901.) AMERICAN SOCIETY FOR
22、 QUALITY (ASQ) ASQ Z1.4 - Sampling Procedures and Tables for Inspection by Attributes (Copies of these documents are available online at http:/www.asq.org or from the American Society for Quality, P.O. Box 3005, 600 North Plankinton Ave., Milwaukee, WI 53203.) AMERICAN SOCIETY FOR TESTING AND MATERI
23、ALS (ASTM) INTERNATIONAL ASTM A313/A313M - Standard Specification for Stainless Steel Spring Wire. (DoD adopted) ASTM D5034 - Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test). (DoD Adopted) ASTM D6193 - Standard Practice for Stitches and Seams. (DoD Adopted) (
24、Copies of these documents are available online at http:/www.astm.org or from ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-81905G(AS) 5 PARACHUTE INDUSTRY ASSOCIA
25、TION (PIA) PIA-C-3953 - Cloth, Duck, Nylon. (DoD adopted) PIA-W-4088 - Webbing, Textile, Woven, Nylon. (DoD adopted) (Copies of these documents are available online at http:/ or from the Parachute Industry Association, 3833 West Oakton St., Skokie, IL 60076.) SAE INTERNATIONAL SAE-AMS-T-22085 - Tape
26、s, Pressure Sensitive, Adhesive, Preservation and Sealing. (DoD Adopted) (Copies of this document are available online at http:/www.sae.org or from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the even
27、t of a conflict between the text of this document and the references cited herein, the text of this document take precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Qualification. Anti-G garment
28、s furnished under this specification shall be products that are authorized by the qualifying activity for listing on the applicable qualified products list before contract award (see 4.3 and 6.5). 3.2 First article. When specified (see 6.2), samples shall be subjected to first article inspection in
29、accordance with 4.4. 3.3 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials shall be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes eco
30、nomically advantageous life cycle costs. 3.4 Materials and components. Except for the metallic materials and parts, unless otherwise specified the materials and components shall have been manufactured not greater than 24 months prior to the date of delivery of the anti-G garment. All materials and a
31、ssembled anti-G garments shall be stored in an environmentally controlled area and protected in a manner to prevent damage from ultra-violet light and environmental contaminants. 3.4.1 Basic materials. 3.4.1.1 High temperature resistant cloth. Except for the bladder, the basic fabric for the Provide
32、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-81905G(AS) 6 anti-G garment, the pull tape for the slide fasteners, the loops for the slide fasteners, and the hanger shall conform to NCTRF PD 01-10, type II. Class designation will be identified as p
33、er contract. Test method 5556.1 of FED-STD-191 shall be replaced with AATCC 135 Type V, A iii utilizing 5 wash cycles. Class I will be U.S. Navy shade sage green 3734, and Class II will be U.S. Navy shade Khaki P1 3729. 3.4.1.2 Polyurethane coated nylon cloth. The material for the bladder (including
34、 the attachment patches) and reinforcement of the inflation external tube covering shall conform to MIL-C-83489, type I, except the finished weight shall be 5.50 to 6.75 ounces per square yard, and the minimum tear strength shall be 5 pounds in the warp direction and 4 pounds in the fill direction.
35、3.4.2 Reinforcements and bindings. Unless otherwise specified herein, the reinforcements shall be made of the basic fabric specified in 3.4.1.1. The bias binding shall be 45 degrees bias cut 1 inches to 1 inches wide from the basic fabric specified in 3.4.1.1. 3.4.3 Spacer material. The spacer mater
36、ial for the bladder and spacer tube of the bladder inflation hose shall conform to MIL-C-43204, type III. (see 6.6). 3.4.4 Adjustment laces and lanyard. The cord for the lanyard and for the adjustment laces shall conform to MIL-C-83242, type I and table I and shall approximately match the shade of t
37、he basic material in 3.4.1.1. TABLE I. Adjustment laces. Size of anti-G Length of Adjustment Laces (Feet) 1/ Garment Waist Area 2/ Thigh Area 2/ Calf Area 2/ Small Regular 12 12 14 Small Long 12 13 16 Medium Regular 12 13 16 Medium Long 12 14 17 Large Regular 13 14 17 Large Long 13 16 19 Large Extra
38、 Long 13 16 19 1/ Dimensions are approximate and shall be governed by the following requirement: Both ends of each adjustment lace shall extend at least 6 inches beyond the open end of the lacing tape when the adjustment laces are completely extended. Both ends of each adjustment lace shall be dippe
39、d in a hot solution of 50 percent beeswax and 50 percent paraffin. 2/ Two per anti-G garment shall be required. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-81905G(AS) 7 3.4.5 Slide fasteners. The slide fasteners (zippers) shall be brass w
40、ith a short tab pull. The slide fasteners shall conform to tables II and III of this specification and to A-A-55634 and drawing 3926AS100 except as otherwise specified herein. The crosswise breaking strength of slide fasteners styles 7A, and 8A shall be 190 lb minimum. The slide fasteners for the bo
41、dy opening shall be type III, style 7A, size MHS and for the leg openings shall be type III, style 7A and 8A, size MHS with S-25 retainer and pin assembly, metal 0308 with a black oxidized finish. The slide fasteners for the thigh take-ups shall be type I, style 4, size MS and for the pockets shall
42、be type I, style 7, size MS. A substitute slide fastener for the body opening, the leg openings, and the thigh take-ups shall be used only when specifically approved by the contracting officer. The tape and the bead of all slide fasteners (including the body opening) shall be a high temperature resi
43、stant polyamide material that has been dyed to approximately match the color of the basic fabric specified in 3.4.1.1. The tape of the slide fastener shall have color fastness in accordance with A-A-55634 except that “fair” colorfastness in lieu of “good” color fastness to light will be acceptable.
44、Slide fasteners from a supplier not identified on the slide fastener ESA (Engineering Support Activity) source control drawing 3926AS100 shall not be used without prior approval of the ESA. The contracting officer shall be contacted for any substitution requests. The finish of the chain and the othe
45、r metal components shall be black. All automatic-locking sliders shall have a pin-type locking device. A thong (see 3.4.7) shall be permanently fastened to each short tab pull with two bar-tacks. TABLE II. Slide fasteners. Location of A-A-55634 Slide Fastener Quantity Type Style Size Body opening 1
46、III 7A MHS 1/ Leg opening 1 III 7A MHS 1/ Leg opening 1 III 8A MHS 1/ Thigh take-ups 2 I 4 MS Pockets 2 I 7 MS 1/ The crosswise breaking strength of slide fasteners styles 7A and 8A shall be 190 lb minimum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS
47、-,-,-MIL-DTL-81905G(AS) 8 TABLE III. Length of slide fasteners. Size of anti-G garment Length (inches of slide fasteners) Body Opening 1/ Leg Opening 2/ Thigh Take-ups Pockets Small Regular 8 26 10 8 Small Long 8 28 11 8 Medium Regular 8 26 11 8 Medium Long 8 28 11 8 Large Regular 8 27 11 8 Large Lo
48、ng 8 29 11 8 Large Extra Long 8 33 11 8 1/ The tolerance for the length of the slide fastener for the body opening shall be 1/8 inch. 2/ The tolerance for the length of the slide fastener for the leg opening shall be inch. 3.4.6 Stiffeners. The stiffeners for the slide fasteners and the stiffeners for the front body and the back body shall be any subdued color made of nylon cloth that conforms to PIA-C-3953, class 2. 3.4.7 Tape nylon aromatic. The tape for the leg and body socket tab assemblies shall 1“ wide, and shal
