1、 MIL-DTL-82L62D 0b 2055263 337 = INCH-POUND MIL-DTL-82162D (MC) SUPERSEDING MIL-C-82162C (MC) 16 October 1997 20 September 1994 DETAIL SPEC I FI CAT I ON CUMMERBUND, MANS - SCARLET (OFFICERS) This specification is approved for use by U.S. Marine Corps, Department of the Navy, and is available for us
2、e by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1. Scope. This specification covers requirements for a mans scarlet cummerbund. 1.2. Classification, and the following classes as specified (see 6.2): The cummerbund will be of one type and size Class 1 - Scarlet with five ho
3、rizontal pleats. Class 2 - Scarlet with six horizontal pleats. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to the Commander (PSE-Q), Marine Corps Systems Command, Quantico, VA 22134-5010 by usin
4、g the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8405 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
5、nse from IHS-,-,-* 7 MIL-DTL-82L62D 99999Ob 20552b4 273 MIL-DTL-82162D (MC) A - 2. APPLICABLE DOCUMENTS 2.1. General. The documents listed in this section are specified - in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification
6、or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2
7、.2. Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of D
8、efense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPEC1 FICAT IONS FEDERAL A-A-50196 - Thread, Silk A-A-52094 - Thread, Cotton CCC-C-426 - Cloth, Cotton, Drill DDD-L-20 - Label: For Clothing, Equipage, and Tentage, (General Use) DEPART
9、MENT OF DEFENSE MIL-C-368 - Cloth, Satin, Rayon and Cloth, Twill, Rayon STANDARDS FEDERAL FED-STD-191 - Textile Test Methods FED-STD-751 - Stitches, Seams, and Stitching (Unless otherwise indicated, copies of the above specifications, standards, handbooks are available from the Standardization Docum
10、ent Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. ) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- NIL-DTL-B2162D W 9999906 2055265 LOT m MIL-DTL-82162D (MC) 2.3. Non-Government Publications. The following document(s)
11、form a part of this document to the extent specified herein. otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of th
12、e documents cited in the solicitation (see 6.2). Unless ANSI/ASQC 21.4- Sampling Procedures and Tables for Inspection by Attributes (Application for copies should be addressed to The American National Standards Institute, 11 West 42nd Street, New York, NY 10036) Department of Defense (DoD) Standard
13、Color Card of Official Standardized Shades for Sewing Thread 1968 (Application for copies should be addressed to The Color Association of the United States, Inc., 409 W. 44th Street, New York, NY 10016-0927.) 2.4. Order of precedence. In the event of a conflict between the text of this document and
14、the references cited herein, the text of this document takes precedence. however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Nothing in this document, 3. REQUIREMENTS 3.1. Standard sample. Standard samples are furnished solely for guidance and informati
15、on to the contractor (see 6.3). Variation from this specification may appear in the standard sample, in which case the specification shall govern. 3.2. First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.3. 3.3. Material. 3.3.1 Basic
16、material. The basic material for classes 1 and 2 shall be cloth, satin, rayon, twill, 3.7 ounce, scarlet, shade 2504, conforming to class 1 of MIL-C-368. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-DTL-82Lb2D W 999990b 20552bb 04b MIL-DTL-8
17、2162D (MC) r 8 3.3.2 Cotton, drill. The end extensions of the cummerbund shall be interlined with cloth, cotton, drill, 7.0 ounces per square yard, unbleached, conforming to type I, class 2 of CCC-C-426. As an alternate, cloth, fusible interlining may be used. Woven Kufner style #G35, National style
18、 200 FL or Crown style 241 or equal. 3.3.3 Elastic webbinq. The elastic webbing shall be made of rayon yarn of suitable grade and denier to meet the requirements specified below, and natural or synthetic rubber strands of a suitable gage to meet the requirements specific below. The webbing shall be
19、composed of two ground warps (one face and one back), one elastic warp, and one filling. The ground warps shall weave in a three up and one down order, with one continuous filling so as to produce a right twill effect on the face and back of the fabric. The elastic strands shall weave in such a mann
20、er as to be over all the back picks and under all the face picks. The finished webbing shall conform to the following: Width (inches) 1-1/8 f. 1/16 Weight per linear yd (ounces) 0.96 minimum Total warp 170 minimum Elastic strands 22 minimum Picks per inch 56 minimum The color of the webbing shall be
21、 black, showing good fastness to laundering, wet (dry) cleaning, crocking and perspiration when tested as specified in Table III. 3.3.4 Thread. 3.3.4.1. Silk thread. The silk thread for machine sewing shall conform to type I, ticket No. A, 3-ply of A-A-50196 for all outside seaming and stitching, co
22、nform to type III, ticket No. C, 2-ply of A-A-50196. The thread for hand sewing shall 3.3.4.2. Cotton thread. Thread for inside seaming and stitching shall be cotton, mercerized finish, ticket No. A, 3-ply, conforming to type III of A-A-52094. good commercial grade. Basting thread shall be a 3.3.4.3
23、. Color and colorfastness. The cotton and silk thread, except thread for basting, shall be scarlet, shade W, cable No. 66040. The thread shall show good fastness to wet (dry) cleaning, laundry and light when tested as specified in the 4 Provided by IHSNot for ResaleNo reproduction or networking perm
24、itted without license from IHS-,-,- flIL-DTL-82162D = 7999906 2055267 T82 MIL-DTL-82162D (MC) applicable thread specification (see DoD Standard Color Card of Official Standardized Shades for Sewing Threads 1968). 3.3.5 Hardware. The buckle and slide shall be made of brass or bronze, nickel plated, a
25、nd shall conform to the design and dimensions shown on Figure 1. 3.3.6 Label. Each cummerbund shall be provided with an identification label, conforming to type VI, class 1 of DDD-L-20. The label shall measure not less than 2-1/2 by 1-1/2 inches. The content and format shall be as follows: Nomenclat
26、ure: (item description) Contract number: Name of contractor: Fiber production identification: NOTE: Size of characters for “Name of contractor“ shall be minimum 6 point (approximately 1/16 inch). 3.4. Desiqn. The cummerbund shall be the U.S. Marine Corps design shown on Figures 2 through 4, having a
27、 one-piece front, five or six horizontal pleats and fusible interlining, with end extensions, two pockets, a plain two-piece back provided with elastic webbing straps at each end, a clasp type metal buckle at the end of the elastic straps, and metal adjusting slide on each strap. 3.5. Patterns. Stan
28、dard patterns will be furnished to the contractor by the Government. The standard patterns shall not be altered in any way and shall be used only as a guide for cutting the contractors working patterns. The standard patterns provide a 1/4-inch allowance for front and interlining seams and 3/8-inch a
29、llowance for front and lining seams and pockets, unless otherwise specified in Table I. Standard patterns shall show seam allowances and directional lines for cutting, and shall be marked or notched for proper placement and assembly of the component parts. 3.5.1 List of pattern parts. The cummerbund
30、s shall be cut from the materials specified in accordance with the pattern parts indicated below: 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-82162D W 99999Ob 20552b8 919 M 1 2 3 4 5 6 MIL-DTL-82162D (MC) I 1 2 1 1 1 1 I ITEM I PATTERN
31、NOMENCLATURE I NO. OF CUT PARTS 1 7 8 9 10 11 I IMaterial: Cloth, satin, rayon I Material: Cloth, cotton, drill Front extension lining 2 Right extension tunnel lining 1 Front interlining 1 Front extension lining 2 Material: Fusible (optional) Marker Front - Front, center Side front, extensions Back,
32、 lining Back lining extension Pocket, right side Pocket, left side 3.6. Construction. 3.6.1 Manufacturina requirements, The cummerbunds shall be manufactured in accordance with the operations and the stitch, seam, and stitching types specified in Table I. 3.6.1.1. Operations. The contractor is not r
33、equired to follow the exact sequence of,operations as listed in Table 1,. but all operations specified shall be used to manufacture the cummerbunds. 3.6.1.2. Stitches, seams. and stitchinss. The stitch, seam, and stitching types specified in Table I shall conform to FED-STD-751. Table I indicates th
34、e minimum and maximum number permitted. The number of stitches per inch as specified in 3.6.1.2.1 Tackinq and backstitchinq. Ends of seams and stitching produced with 301 type stitch, when not caught in other seams or stitchings, shall be securely backtacked not less than 1/4 inch, Thread breaks (al
35、l stitch types) shall be secured by stitching back of break not less than 1/2 inch. 3.6.1.3. Shade markinq. The component parts of the cummerbund shall be shade marked to ensure a uniform shade and size b Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
36、-,-NIL-DTL-82Lb2D 99Ob 2055269 855 MIL-DTL-82162D (MC) throughout the garment. except : Any method of shade marking may be used a. Metal fastening devices. b Sew-on shade tickets. c Adhesive type tickets which show discoloration or leave traces of paper or adhesive mass to the material upon removal
37、of the tickets. TABLE I. Manufacturinq requirements. - NO 1 - 2 OPERAT I ON :ut tinq. i. Cut cummerbund in strict iccordance with the patterns hrnished. 3. Cut all materials in the iirection indicated by directional lines on pattern. c. Cut all component parts of the cummerbund from one piece of bas
38、ic material. d. Cut the elastic webbing for the left side of the cummerbund 8 inches long and or the right side 15 inches long. e. The use of drill holes is prohibited. ReDlacement of damaaed parts. a. Replace at time of cutting any part containing damages, such as holes, or seriously weakening defe
39、cts, such as smashes, multiple floats, and slubs likely to develop into holes. b. Replace any part damaged during the manufacturing process by needle chews, which may be expected to develop into a hole, scissors or knife cuts, tears, holes, mends and burns. STCH TYPE SEAM/ STCH TYPE ;TCH/IN NDL BOB/
40、 LPR 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- NO flIL-DTL-82Lb2D W 99999Ob 2055270 577 9 MIL-DTL- 821 62D (MC) TABLE I. Manufacturins reauirernents - Continued. OPERAT I ON Shade markinq. a. Mark or ticket (see 3.6.1.3) all component parts
41、cut from basic material in order to ensure proper assembly and a uniform shade throughout the cummerbund. b. Adhesive tickets, when used, shall be adhered to the inside of the cummerbund. Sew on identification label. Finished appearance. The label shall be properly positioned and sewn to the back of
42、 the cummierbund. a. Position the identification label at the center of the back lining, with the top edge 1 inch from the top edge of the back. Sew the label to the back lining with a single row of stitches 1/16 inch from each edge. Make center front. Finished appearance. All pleats and joining sea
43、ms shall finish smooth and flat without distortions. The seams shall start and finish evenly. The pleats shall finish with the outside folded edge towards the top of the front. a. The front shall be made of one ply of rayon satin material and one ply of interlining material. When the cotton drill in
44、terlining is used, the front shall be pleated first and have side extensions joined before shaping of canvas. When fusible interlining is used, the front shall be fused before pleating. STCH TYPE 301 SEAM/ STCH TYPE SSa-1 STCH/IN 10-14 NDL A BOB/ LPR A 8 Provided by IHSNot for ResaleNo reproduction
45、or networking permitted without license from IHS-,-,- NO TCH/IN 7 I 10-14 10-14 10-14 5 6 STCH MIL-DTL-821b2D 0b 2055273 403 m MIL-DTL-82162D (MC) STCH TABLE I. Manufacturins requirements - Continued. OPERATION ake center front. (contd) . Fold the center front lengthwise, nside out, in accordance wi
46、th otches on the patterns, forming the leats. Stitch each pleat from end o end with a continuous row of titches. The stitching at the ends f the pleat shall be 1 inch from the ower folded edge and shall extend or a distance of approximately 2 nches from each end. The stitching or the remainder of th
47、e pleat shall le 1/2 inch from the folded edge. :. Press front with the outside :olded edge of each pleat towards the :op of the cummerbund. 1. Mark and trim the front in rccordance with the pattern marker. lark the upper edge of the position )f two pockets. fake Dockets. ?inished appearance. The po
48、ckets shall be uniformly stitched and finish smooth and flat without :awing dis tortion. P. Each pocket shall be made of one ?ly of basic material. 3. m the outside of the front at the nark, with edges even and with notches matching. Stitch the pocket to the front and interlining 3/8 inck rom top ed
49、ge, from notch to notch. e. Extend depth of notches to the seam, turn the pocket and raise stitch 1/16 to l/8 inch from the seamed edge. d. Turn up bottom end of pocket eve1 at the upper and side edges. Stitch the two plies of pocket together at the sides and bottom folded edge wit1 a 1/4 inch seam. Tack the upper end: of pocket opening to the front of cummerbund to complete the pocket. Position
