NAVY MIL-DTL-82929 A (1)-2002 INITIATOR EXPLOSIVE ACTUATED JAU-24 A《JAU-24 A引发爆炸性的驱动》.pdf

上传人:dealItalian200 文档编号:978923 上传时间:2019-03-13 格式:PDF 页数:2 大小:82.51KB
下载 相关 举报
NAVY MIL-DTL-82929 A (1)-2002 INITIATOR EXPLOSIVE ACTUATED JAU-24 A《JAU-24 A引发爆炸性的驱动》.pdf_第1页
第1页 / 共2页
NAVY MIL-DTL-82929 A (1)-2002 INITIATOR EXPLOSIVE ACTUATED JAU-24 A《JAU-24 A引发爆炸性的驱动》.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、INCH-POUNDMIL-DTL-82929A (OS)AMENDMENT 15 September 2002DETAIL SPECIFICATIONINITIATOR, EXPLOSIVE ACTUATED, JAU-24/AThis amendment forms a part of MIL-I-82929 (OS), dated 13 September 2000, and is approved for use by the Naval Sea SystemsCommand, Department of the Navy, and is available for use by al

2、l departments and agencies of the Department of Defense.PAGE 33.2.2: Delete in its entirety and replace with the following:“3.2.2 Mc Cormick Selph P/N 827185-105. The primary components for the initiator McCormickSelph P/N 827185-105 are the two M42C1-979 percussion primers, the explosive mix, the d

3、elay fuse, thedelay mix and the booster charge.”3.2.2.1: Delete in its entirety and replace with the following:“3.2.2.1 M42C1-979 percussion primers. The dual M42C1-979 percussion primers used in theMcCormick Selph P/N 827185-105 initiator shall be manufactured and tested in accordance withMIL-P-204

4、44. The primers shall be loaded into the initiators within 24 months of new primer acceptancetesting or 12 months of primer recertification testing.”PAGE 43.3, Third line: Delete “3.3.2 through 3.3.2.3, respectively.” and substitute “3.3.2 through 3.3.2.5,respectively.”.3.3.1: Delete in its entirety

5、 and replace with the following:“3.3.1 Delay cartridge assembly (SCOT P/N 6078150 or McCormick Selph P/N 827226-105)inspection.”PAGE 104.3.11, Fifth line: Delete “Drawing 850AS821. See figure 1 for general test setup schematic.Instrumentation shall” and substitute “Drawing 850AS821. Instrumentation

6、shall”.PAGE 11Figure 1: Delete the figure and its title.AMSC N/A 1 of 2 FSC 1377DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-82929A (OS)AMENDMENT 12Preparing Activity:Navy OS(Project 1377-0178)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • GOST 32654-2014 Polymer composites Thermosetting prepregs and premixes Determination of cure characteristics《聚合物复合材料 热固性预浸料和预混料 固化特性的测定》.pdf GOST 32654-2014 Polymer composites Thermosetting prepregs and premixes Determination of cure characteristics《聚合物复合材料 热固性预浸料和预混料 固化特性的测定》.pdf
  • GOST 32655-2014 Polymer composites Thermosetting prepregs and premixes Methods of determination flowability maturation and shelf life《聚合物复合材料 热固性预浸料和预混料 流动性 成熟和保存限期的测定方法 》.pdf GOST 32655-2014 Polymer composites Thermosetting prepregs and premixes Methods of determination flowability maturation and shelf life《聚合物复合材料 热固性预浸料和预混料 流动性 成熟和保存限期的测定方法 》.pdf
  • GOST 32657-2014 Polymer composites Test methods Determination of temperature of deflection under load《聚合物复合材料 试验方法 负荷变形温度的测定》.pdf GOST 32657-2014 Polymer composites Test methods Determination of temperature of deflection under load《聚合物复合材料 试验方法 负荷变形温度的测定》.pdf
  • GOST 32658-2014 Polymer composites Determination of mechanical properties in the plane of shear reinforcement by a tensile test at an angle of ± 45 degree《聚合物复合材料 在45度左右的角度下采用拉伸试验测.pdf GOST 32658-2014 Polymer composites Determination of mechanical properties in the plane of shear reinforcement by a tensile test at an angle of ± 45 degree《聚合物复合材料 在45度左右的角度下采用拉伸试验测.pdf
  • GOST 32659-2014 Polymer composites Test methods Determination of apparent interlaminar shear strength by short-beam method《聚合物复合材料 试验方法 采用短梁法测定表观间层抗剪能力》.pdf GOST 32659-2014 Polymer composites Test methods Determination of apparent interlaminar shear strength by short-beam method《聚合物复合材料 试验方法 采用短梁法测定表观间层抗剪能力》.pdf
  • GOST 32660-2014 Polymer composites Prepregs Determination of resin flow《聚合物复合材料 预浸料 树脂流动率的测定》.pdf GOST 32660-2014 Polymer composites Prepregs Determination of resin flow《聚合物复合材料 预浸料 树脂流动率的测定》.pdf
  • GOST 32661-2014 Fibre reinforced thermosetting plastic pipes and parts of pipelines General specifications《纤维增强热固性塑料管和管道部分 通用规格》.pdf GOST 32661-2014 Fibre reinforced thermosetting plastic pipes and parts of pipelines General specifications《纤维增强热固性塑料管和管道部分 通用规格》.pdf
  • GOST 32662-2014 Polymer composite components of the ventilating equipment Specifications《通风设备的聚合物复合组件 规格》.pdf GOST 32662-2014 Polymer composite components of the ventilating equipment Specifications《通风设备的聚合物复合组件 规格》.pdf
  • GOST 32663-2014 Polymer composite components of the pumps for special purpose Specifications《特殊用途泵的聚合物复合组件 规格》.pdf GOST 32663-2014 Polymer composite components of the pumps for special purpose Specifications《特殊用途泵的聚合物复合组件 规格》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1