1、I MIL-G-82Z4LC L( 9949906 044b437 5 I . z MIL-G-82241C 17 January 1979 SUPERSEDING MIL-G-82241B 17 May 1973 - ;e/ MILITARY SPECIFICATION i GLOVE INSERTS, RADIOACTIVE CONTAMINANTS PROTECTIVE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE
2、1.1 Scope This specification covers the requirements for knitted cotton glove inserts, of one type and size only. 2. APPLICABLE DOCUMENTS *2.1 Issues of Documents The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification
3、to the extent specified herein. SPECIFICATIONS FEDERAL V-T-276 - Thread, Cotton HiLITARY MiL-B-17757 - Boxes Shipping, Fiberboard, (Modular Sizes) MIL-T-43548 - Thread, Polyester, Cotton-Covered b STANDARDS b FEDERAL FED-STD-191 - Textile Test Methods FED-STD-751 - Stitches, Seams, and Stitching Ben
4、eficial comente (recommendations, additions, deletions) and any pertinent data which may be of use in. improving this document should be addressed to: Navy Cltohing p Table I - Physical requirements Minimum Requirement Characteristic Weight oz/sq yd 2. a Wales / in 24 Courees/in 26 * 3.3.2 Thread Th
5、e thread for seaming and stitching the gloves shall be cotton, natural or white in color, conforming to type 1AL or 1A2, ticket no. 70, 2 ply, of Y-T-276 or as an alternate thread, polyester, cotton-covered, size 70 conforming to MIL-T-43548 may be used. 3.4 Design The gloves shall be an inseam sewn
6、, 5-finger silhouette, ambidextrous design, as shown on figure 1. 3.4.1 Figure Figure 1 is furnished for information purposes only. To the extent of any inconsistencies between the written specification and the figure, the written specification shall govern. 3.5 Patterns the contractor for use in cu
7、tting the working patterns (see 6.3). patterns shall be identical to the government patterns.- Neither the government patterns nor the working patterns shall be altered in any way. Standard patterns will be furnished by the government to The working 3.5.1 List of pattern parts The component parts of
8、 the gloves shall be cut from the following material as specified and in strict conformance with the number of parts required for the manufacturing process as follows: Material Nomenclature of pattern parts Cut parts/pair Cloth, cotton jerey knit Interchangeable face 4 3.6 Construction 3 Provided by
9、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-8224LC 4 777990b 044b440 5 mi f MIL-G-82 241C P *3.6.1 Stitchap, seams, and stitching Stitch, seams, and stitching types specifiad in Table 13: shall conform to FED-STD-751. When two or Are meihode or stitch
10、 types are given for the same part of an operation, any one may beued. finieh a minimum of 1/8 inch from the raw edge. may be used. Unlees otherwise specified, all stitching shall Trimmer attachment 3.6.2 Stitches per inch The minimm and maximum number of stitches per inch shall be as specified in T
11、able II. *3,6,3 Thread breaks and ends of stitching Ends of all stitching produced with 301 stitch types shall be backtacked not less than 1/4 inch. Both ends of all stitching produced with 401 stitch type shall have a 1/4 to 1/2 inch chain extending beyond each end. shall be secured by stitching ba
12、ck of break not less than 1/2 inch. Skipped stitches or thread breaks (401 stitch type) may be repaired using. 301 stitch type. Thread breaks (all stitch types) 3.7 ManufacturiaR qperat,ion requirements The gloves shall be manufactured in accordance with operation requirements specified in Table II.
13、 contractor ia not required to follow the exact sequence of operations listed provided that the finished gloves are identical to those produced by following the sequence of operations listed in Table II. The 4 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro
14、m IHS-,-,-MIL-G-82241C 84 m 9777906 0446441 7 m MIL-G-82241C F 4 L 1 A hl O I- ll ii bl m “ I l-l “ al if% “ FI o kO mou .i. a 2 u 7 O Y 2i al a al O r w w O I H H ti Lz k w 4 f al a 2 k d s a Lr b .- . . rl N m U n 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without licen
15、se from IHS-,-,-I .I MIL-G-82241C 84 9 9979906 0446442 9 9! -. 1 MIL-582241C z2 *3.8 Measurements The finished gloves shall conform to the dimensions Ll as Specified in Table III. inches. with the gloves laid flat under no tension. All dimensions and tolerances are expressed in The measurements shal
16、l be made .at location A, B, and C Table III - Finished measurements Tolerance Location of measurement Dimens ion A Overall length C Width across top opening NOTE: A measurement taken from tip of second finger to.top opening, B measurement taken across palm at thumb crotch C measurement taken across
17、 the top opening. established by this specification. exceed the applicable acceptable quality levels, + 114 114 + 1/4 14 - B Width across palm 4 112 3 718 - A, B, and C refer to figure 1. 3.9 Workmanship The finished gloves shall conform to the quality The occurrence of defects shall not 4. QUALITY
18、ASSURANCE PROVISIONS 4.1 Responsibility for Inspection Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all in- spection requirements as specified herein. contract or order, the contractor may use his own or any other facilities suita
19、ble for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to pre
20、scribed require- ments. Except as otherwise specified in the 4.1.1 Certificate of compliance Where certificates of compliance are submitted, the Government reserves the right to check test such items to determine the validity of the certification. *4,2 Classification of inspection The inspection req
21、uirements specified herein are classified as -follows ! 1. 2, First Article inspection (see 4*3). Quality Conformance inspection (see 4.4). 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-T MIL-G-224LC 4 = 9979906 04Yb443 O i d MIL-G-8224 1C Compon
22、ent Cloth, co ttor jersey knit 4.3 First article inspection When required, the first article submitted in accordance with 3.2 shall be inspected for compliance with design, con- LJ Requirement Test Characteristic Paragraph Method Ma teria1 identification 3.3.1 1200 y Type of knit 3.3.1 Visual 2-1 Co
23、lor 3.3.1 Visual 2-1 Weight Table I 5041 Wales per inch Table I 5070 Courses per inch Table I 5070 7 struction, workwanship, appearance, and dimensional requirements as specified in 4.4.2.1 and 4.4.2.2. 4.4 Quality conformance inspection Inspection shall be performed in accordance with the pgev.e.io
24、ns set forth in MIL-STD-105, except where otherwise indicated . herein. *4.4,1 Component: and material inspection In accordance with 4.1, components and materials shall be inspected and tested in accordance with all the require- ments of referenced specifications, drawings, and standards unless othe
25、rwise excluded, amended, modified, or qualified in this specification or applicable purchase document. In addition, the finished knitted fabric shall be tested for characteristics specified in section 3 in accordance with referenced test methods specified in Table IV of FED-STD-191. full width of th
26、e finish fabric. The lot size shall be expressed in units of one yard each. unacceptable if one or more units fail to meet any requirement specified. All test reports shall contain the individual value utilized in expressing the final result. The sample unit shall be 1 yard The sample size shall be
27、as shown below and the lot shall be Lot size (yards) Sample size 800 or less 2 801 up to and including 22,000 3 22,001 and over 5 Table IV - Fakric tests L, 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-G-8224LC 84 m 7777906 0446444 2 mg I
28、MIL-G-82241C 4.4.2 Examination Qf the end item The defects found during the examination of the end item ehall be classified in accordance with 4.4.2.1 and 4.4.2.2, The applicable inpeetion level and acceptable quality levels (AQL) shall. be as indicated in 4.4.2.3. size shall be expressed in units o
29、f one glove. The sample unit shall be one glove and the lot 4.4.2.1 Visual examination The gloves ehall be examined for defects classi- fied in accordance with the list below: Classification Defect6 Major Minor MATERIAL DEFEXTS AND DAMAGES a. Any hole, tear, float, smash, drop stitch, mend, or needl
30、e chew X of the normal diameter of yarn being used b, Any pulled or snagged yarn X C. Slubby yarn more than twice the diameter X CLEANNESS a. Any permanent spot or stain (excluding pattern in any direction X b. Thread end not trimmed X C. Loom threads not removed X COLOR printing marks) greater than
31、 1/4 inch Other than specified CUTTING Any part not cut in accordance with specified pattern X SEAMS AND STITCHINGS a. Accuracy of stitching 1. Seam twisted or pleated X 2. 3, Ends of stitching produced with a 301 etitch type, backtacked less than 1/4 inch Ends of stitching produced with 401 stitch
32、type, having chain extended lees than 1/4 inch or more than 1/2 inch beyond end not having a chain extending beyond each end X 4, Ende of stitching produced on 401 stitch type b u X X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-:Ll r Classificati
33、on Defects . Major Minor “ SEAMS AND STITCHINGS (contd) 5, 6. Thread breaks not repaired properly Inseam stitching-less than 1/8 inch from edge b. Any open seam . NOTE: One or more broken stitches or run Offs constitute an open seam X X c. Seam or stitch type not as specified d. Stitch. tension (too
34、 tight or too loose) . e. Stitches perinch (scored when the condition existe on more than hal the length of seau or stitching) 1, 2. X One BtitCh more or less than the maximum Two stitches more or less than the maximum X or minimum specified or minimum specified X ASSEMBLY DETAIL )u X a. Not constru
35、cted as specified b, X Gloves not layed off or formed on heated forms 4.4.2.2 Dimensional examination The gloves shall be examined for dimension in accordance with established tolerances (see 3.8). The inspection levels and acceptable quality levels (AQLs) expressed in defects per 100 unite for visu
36、- and dimensional examination shall be as follows: 4,4.2,3 Inspection levels and acceptable quality levels AQL s Inspection level Major Total 2.5 6.5 4.0 I s -2 For defects appllcable to 4.4.2.1 - For defects applicable to 4.4.2.2 9 Provided by IHSNot for ResaleNo reproduction or networking permitte
37、d without license from IHS-,-,-MIL-G-8 2 2 4 1C 4.4.3 Examination of packaging requirements made to determine that packaging, packing and marking complies with section 5 requirements of this specification. accordance with the list below. tainer fully prepared for delivery, except that it need not be
38、 closed. Defects of closure listed below shall be examined on shipping containers fully prepared far delivery. in the end item inspection lot. AQL shall be 2.5 defects per 100 units (DHU). An examination shall be Defects shall be scored in The sample &it shall be one shipping con- The lot: size shal
39、l be the number of shipping containers The inspection level shall be S-2 and the 5. PACKAGING 5.1 Preservation-packaginq Packaging shall be level A or C as specified (see 6.2). 5.1.1 Level A Twelve pairs of gloves shall be evenly stacked in a bundle The bundle shall be securely tied with every six p
40、airs reversed end to end. approximately three inches from each end with cotton tape or twine. 5.1.2 Level C (Commercial packaging) Gloves shall be packaged to afford adequate protection against physical damage during shipment from the supply source to the first receiving activity. be the same as tha
41、t normally used by the contractor for retail distribution. 5.2 Packinq Packing shall be level A, B, or C as specified (see 6.2). 5.2.1 Level A One hundred and eighty (180) pairs of gloves, packaged , Level A packages shall be packed flat, one in length, three in The packages and the quantity per pac
42、kage shall as specified in 5.1, shall be packed in a fiberboard shipping container assembled and closed conforming to class weather resistant, grade V28, size 1 of MIL-B-17757. width and four in depth, with the length of the bundles parallel to the side panels of the container. In the remaining spac
43、e at the opposite end panel, placa three bundles on side edge, one in length and three in depth, with the length of the bundles parallel to the end panel. Each container shall have the contenta completely covfared on-the top and bottom with a sheet of commercial kraft paper. 4 5.2.2 bevel B One hund
44、red and eighty (180) paire of gloves, packaged as . specified in 5.1, shall be packed in a fiberboard shipping container assembled and closed con for mix to class domestic, grade 200, size 1 of MIL-B-17757. Level A packages ehall be packed flat, one in length, three in width and four in depth with t
45、he length of the bundles parallel to the side panels of the container. ln the remaining space at the opposite end panel, place three bundles on side-edge, one in length and three in depth, with the length of the bundles parallel to the end panel. completely covered on the top and bottom with a sheet
46、 of commercial kraft paper, Each container shall have the contents 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-T HIL-G-Z24LC 84 U 797770b 044b447 B = f MIL-G-82241C 2= La 5.2,2.1 When specified (see 6.2), the shipping container shall be a grad
47、e VC, V3s or V4s fiberboard box fabricated in accordance with MIL-B-17757 and closed in accordance with the appendix of the container specification, . . . 5.2.3 Level C (Commercial packing) Gloves, packaged as specified in 5.1 shall be packed in a manner to inaure carrier acceptance and safe deliver
48、y at destination at the lowest transportation rate for such supplies. per shipping container shall be the same as that normally used by the contractor for retail distributiq. Manual, Uniform Classifcation Rules or National Motor Freight Classification Rules, a6 applicable. The quantity Container sha
49、ll comply with the US Postal Service 5.3 Marking In addition to any special marking required by the contract or order, shipping containers shall be marked in accordance with MIL-CTD-129. 6. NOTES 6.1 Intended use The gloves covered by this specification are intended for uae by personnel workin as an insert in combina ! ion with MIL-G-82242 Glove, Shells, Radioactive Contaminants Protect
