1、- MIL-G-8706bA 8Li W 99977060430734 7 - 5-15- II MIL-G-87066A 22 September 1988 SUPERSEDING 18 May 1979 MIL-G-87066(NU) MILITARY SPECIFICATION GLOVES, CHEMICAL AND OIL PROTECTIVE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope.
2、This specification covers the requirements for unsupported, dipped rubber gloves, with a cotton-flock lining. 1.2 Classification. The gloves shall be procured in the following sizes as specified (see 6.2): Schedule of Sizes 7, 8, 9, 10, 11 2. APPLICABLE DOCUMENTS * 2.1 Government documents. Benefici
3、al comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Docu
4、ment Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS A ZL PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted wit
5、hout license from IHS-,-,-MIL-G-87066A * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the iss
6、ue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL PPP-B-636 - Boxes, Shipping, Fiberboard NN-P-71 - Pallet, Material Handling, Wood, Stringer, Construction, 2 Way and 4 Way (Partial) MILITARY MIL-0
7、-82672 - Otto Fuel II MIL-P-15011 - Pallet, Material Handling, Wood, Post Construction, 4 Way Entry STANDARDS FEDERAL FED-STD-601 - Rubber, Sampling and Testing MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-147 - Palletized Unit Loads MIL-STD-168 - Visual Inspection Guide for All Rubber Gloves - Sampling
8、 Procedures and Tables for Inspection by - Marking for Shipment and Storage Attributes Except Surgical (Copies of specifications, standards, drawings, and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as direc
9、ted by the contracting officer. ) * 2.1.2 Other Government documents, drawings, and publications. The following .other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on
10、 the date of the solicitation. LAWS AND REGULATIONS US POSTAL SERVICE MANUAL (Copies of the manual may be obtained from the Superintendent of Documents, US Government Printing Office, Washington, DC 20402-0001.) 2 i 4- I Provided by IHSNot for ResaleNo reproduction or networking permitted without li
11、cense from IHS-,-,-MIL-G-870hbA q 9999906 OLt1073h O W MIL-G-87066A NAVSEA - S-6340-AA-MMA-010 (Applications for copies may be addressed to the Naval Publications and Forms Center, 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) * 2.2 Other publications. The following document(s) form a part of thi
12、s specification to the extent specified herein, Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issu
13、e of the nongovernment documents which is current on the date of the solicitation. NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applications for copies should be addressed to the American Trucking Association, ATTN: Traffic Department, 1616 P Street,
14、 N.W., Washington, DC 20036-1404.) UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Applications for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606-5808.) AMERICAN SOCIETY FOR TESTING AND MATERI
15、ALS D-412 Test for Tensile Strength D-471 Test for Change in Properties of Elastomeric Vulcanizates Resulting from Immersion in Liquids D-573 Test for Air Heat Test, Air Heating Medium (Applications for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, P
16、hiladelphia, PA 19103-1187,) * 2.3 Order of precedence. In the event of a conflict between the text of this specificationthe references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a
17、 specific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in the sample in which case this specification shall govern. 3 Provided by IHSNot for R
18、esaleNo reproduction or networking permitted without license from IHS-,-,-_II_ _I_-_ MIL-G-70bbA 8L( m 9799706 0430737 2 W MIL-G-87066A 3.2 First article. When specified, the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Materials. 3.3.1 Rub
19、ber Compounds. The gloves shall be made of a earboxylated butadiene-acrylonitrile rubber latex, suitably compounded without the use of plasticizers or inert fillers, and vulcanized to meet the requirements specified herein (see 4.4.1). 3.3.1.1 Color. Unless otherwise specified by the procuring activ
20、ity, the I approved color of the finished gloves shall be either white or in light shades of green or blue (see 6.5). 3.3.2 Lining. Each finished glove shall have a cotton flock lining suitably adhered to the rubber compound on the inside.(see 4.4.1 and 6.4). m . * 3.4 Label. Each finished glove sha
21、ll have a combination identification and cautionary statement inscription as shown below, legibly marked and centered on wrist of palm side, with the bottom of the label 3/4 to 7/8 inch from the bottom edge of cuff. The inscription shall be made either by printing, stenciling, or stamping. The size
22、of the lettering for the identification information shall be not less than 1/8 inch in height. The cautionary statement shall be printed in larger letters than all other lettering in the label. The marking ink shall be of any permanent contrasting color, provided it is consistent with the approved c
23、olor requirements of the finished glove (see 3.3.1.1): CONTRACT NO: DLA 100-00-0-0000 (EXAMPLE) STOCK NO: 8415-00-000-0000 (EXAMPLE) SIZE : 9 (EXAMPLE) FOR PROTECTION AGAINST USN OTTO FUELS, DO NOT REUSE 3.5 Physical and chemical requirements. The finished gloves shall conform to the physical requir
24、ements shown in Table I when tested as specified in 4.5. Table I - Physical and Chemical Requirements of Finished Gloves Characteristic Requirement Thickness, inch: Cuff, palm, two crotch Tensile strength, p.s.i. Ultimate elongation, percent Area change, percent after immersion in Fuel B - 35.0 Min
25、i mum Maximum and two fingertip areas .O13 - Original 3000 - After aging 2700 - Original 380 - After Aging 360 - Pass 1/ - Porosity - 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-G-870bbA 4 E 779770b 0420738 4 MIL-G-87066A Characteristic Re
26、quirement Resistance to permeation by; Minimum Maximum Otto fuel: Cumulative permeation, 2 hrs period, Permeation rate at 2 hrs, micrograms/minute - .10 micrograms - 1.0 - 1/ There shall be no evidence of air bubbles. The dipping forms utilized by the contractor in his provided that the gripping sur
27、face of the finished gloves (palm and fingers) has a non-slip embossed pattern design. may be made from any commercially designed mold, * 3.7 Design. The gloves shall be of a standard four finger and thumb style, with either a pinked, natural dipped or rolled bottom cuff edge (see Figure 1). 3.7.1 F
28、igures. Figures 1 through 5 are furnished for information purposes only. When inconsistencies exist between the written specification and the figures, the written specification shall govern. 3.8 Chlorination. The rubber surfaces of each finished glove shall be chlorinated to reduce tackiness* Excess
29、ive chlorination shall be avoided to prevent excessive stiffening, discoloration, or slipperiness (see 4.4.1). J( 3.9 Measurements. The sizes and measurements 8f the finished gloves shall conform to the dimensions as specified in Table II. All measurements and tolerances are expressed in inches and
30、shall be taken with the glove flattened without pulling or stretching. Table II - Finished Measurements Size Tolerance Measurement 7 8 9 10 11 Overall Length (A) 13 13 13 13 13 Mini mum + 1/4 Width of palm (B) 3 718 4 . 4 318 4 718 5 318 - Width of wrist (C) 3 1/4 3 5/8 3 7/8 4 3/4 5 1/8 Min i mum W
31、idth of cuff (D) 4 1/2 4 3/4 5 1/4 5 5/8 6 - + 114 NOTE: A through D refer to Figure 1. A. Measurement shall be taken on back side from tip of second finger to top B. Measurement shall be taken across the back at thumb crotch, folded edge to C. D. open edge of glove. folded edge. side, folded edge t
32、o folded edge. folded edge to folded edge. Measurement shall be taken across the narrowest part of the wrist on back Measurement shall be taken across the top open edge of glove on back side, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_- - -_ -
33、MIL-G-870bbA 4 999990b 0430739 b MIL-G-87066A 3.10 Workmanship. The finished gloves shall conform to the quality established by this specification. The occurrence of defects shall not exceed the applicable acceptable quality levels. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection.
34、Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the contractor may use his own or any other facilities suitable for performance of the inspection
35、requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conforin to prescribed requirements. * 4.1.1 Responsibil
36、ity for compliance, All items must meet all requirements of sections 3 and 4. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the cont
37、ractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit th
38、e Government to acceptance of defective material. 4.1.2 Certificate of compliance. Where certificates of compliance are submitted, the Government reserves the right to check test such items to determine the validity of the certification. * 4.2 Classification of inspection. The inspection requirement
39、s specified herein are classified as follows: 1. First article inspection (see 4.3). 2. Quality conformance inspection (see 4.4). 4.3 First article inspection. Whe required, the first article submitted in accordancy with 3.2 shall be inspected as specified in 4.4.2.1 and 4.4.2.2 for compliance with
40、design, construction, workmanship, and dimensional requirements. 4.4 Quality conformance inspection. Sampling for inspection shall be performed in accordance with MIL-STD-105, except where otherwise indicated. 4.4.1 Component and material inspection. In accordance with 4.1 above, components and mate
41、rials shall be tested in accordance with all the requirements of referenced specifications, drawings, and standards unless otherwise excluded, amended, modified, or qualified in this specification or applicable procurement documents. A certificate of compliance shall be submitted for the material id
42、entification of the rubber compound (see 3.3.1), the cotton flock lining for the inside of the gloves (see 3.3.2), and for the required chlorination process of the finished gloves (see 3.8). 4.4.2 Examination of the end item. Examination of the end item shall be in e 6 Provided by IHSNot for ResaleN
43、o reproduction or networking permitted without license from IHS-,-,-MIL-G-87066A 0 accordance with 4.4.2.1 through 4.4.2.3. The sample unit shall be one completely fabricated glove, and selection shall be made in pairs. Pairing defects shall be scored as a single defect. The lot size shall be expres
44、sed in units of one glove each. * 4.4.2.1 Visual examination. Classification Major Minor Defect Pai ring I Gloves not mated in pairs e.g., two left, two right Definite variation in color or appearance gloves submitted as a pair, not same size X X Design Any characteristic not in accordance with spec
45、ified requirements (unless otherwise classified herein) Color Not as specified Cleanness a. Grease, oil stain, or dirt on glove which cannot b. Not clean, i.e., dirty, but dirt can be be easily removed easily removed Construction and Workmanship (applicable to inside and outside of glove) a. Any cut
46、, hole, tear, rip or rupture through material b. Evidence of improper vulcanization, e.g, c. Any repair or patch d. Any blister, open or closed e. Any pinch, thin spot, pit, abraded area, deep crease, or similar defective condition resulting in a thickness at the defect less than the minimum thickne
47、ss allowed tacky, etc. f. Any burned spot g. Any malformation or distortion: h. Any solid rubber ridge, run, or lump i. - Seriously affecting serviceability - Affecting Serviceability, but not seriously Not constructed as specified, i.e., bottom open edge of glove not rolled, natural edge or pinked
48、as specified Bottom rolled edge (when applicable) of glove crooked or loose Cotton flock lining omitted on inside of glove j. k. Length not as specified 1. X X X X X X X X X X X X X X X x- X NOTE: For rubber defect illustrations, see MIL-STD-168 Markings 7 Provided by IHSNot for ResaleNo reproductio
49、n or networking permitted without license from IHS-,-,-I_ _ _ _I-_- -_ -_ - - _ - - _ MIL-G-8706bA 4 W 9999906 04L0741i 4 MIL-G-87066A Classification Defect Major Minor Marking b. c. Not permanent, i.e., can be easily rubbed off with a. Missing, incorrect or illegible X Misplaced, height of characters not as specified, or not accomplished as specified X a moistened thumb X 4.4.2.2 Dimensional examination
