1、1. 4 MIL-1-23951 13 m 77797Ob 03040bb T H MI L- 1-23951- (WEP) 19 August i964 MILITARY SPECIFICATION IGNITION MATERIAL, PE LLETED, PYROTECHNIC FOR IGNITER MARK 265 This specification has been approved by the Bureau of Naval Weapons, Department of tk Navy SCOPE 1.1 type of pelleted pyrotechnic igniti
2、on material. This specification defines the minimum requiremenis for one 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on the date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. STANDARDS Mi I i tary MI L
3、-STD-129 Marking for Shipment and Storage DRAW IN GS Bureau of Naval Weapons, Department of the Navy 25 16382 Charge, Igniter Assembly (When requesting any of the above documents, give the title and complete designation of the item as shown above. Copies of this specification and other unclassified
4、specif cations, standards, and publications required by contractor in connection with specific procurement functions may be obtained from the Commanding Officer, Naval Supply Depot (Code 105), 5801 Tabor Avenue, Philadelphia 20, Pennsylvania. Drawings may be obtained from the Commanding OFficer, Nav
5、al Ordnance Plant (CTBO), Iroquois Station, Louisvi I le, Kentucky a Contractors should requisi tion forms from the cognizant field contract administrator. Field contract administrators should obtain BuWeps Instructions from the Forms and Publications Segment of the Navy Supply System in accordance
6、with NAVSANDA Publication 2002. All other documents should be obtained from the procuring activiiy or as directed by the - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-23951 13 7777906 030qO67 LI I MIL-1-2395 1 (WEP) 49 CFR 71-90 Code of Fed
7、eral Regulations (Request copies from the Superintendent of Documents, Government Printing Office, Washington 25, D. C.) I 3. REQUIREMENTS factured using the process methods and equipment proposed for producfion. Any significant changes after preproduction approval must be approved by the procuring
8、activity prior to incorporation into production. It shall be the responsibility of the contractor to inform the procuring activity of proposed changes after approval of the preproduction sample. In the event of significant changes in the process methods and equipment which in the opinion of the proc
9、uring activity may adversely affect the characteristics of the material, additional preproduction samples may be required. 3.2 Composition. -The chemical composition of the pellets shall be 1 only the ingredients and weight percentages stated on the drawing. Provided by IHSNot for ResaleNo reproduct
10、ion or networking permitted without license from IHS-,-,-TABLE I PHYSICAL PROPERTI ES Characteristics Limits Min i mum Maximum Calorimetric Value (Average) 1500 Calories per gram Crush Strength (Average) 6500 grams Dimensions: Length Diameter O. 177 inch O. 197 inch 0.121 inch 0.129 inch Pe 1 let De
11、nsity (Average) 1.63 grams 1.77 grams per cubic cm. per cubic cm. Pel let Weight (Average) O. 060 grams 3.4 Workmanship. -The material furnished under this specification shall be a uniform product free from foreign materials. It shall be uniform in quality and manufactured in accordance with standar
12、d manufacturing procedures of the industry. 3.5 Data Requirements. -No data is required by this specification or by applicable documents referenced in section 2 unless specified in the contract or order (see 6.2). 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection. -Unless otherwise s
13、pecified in the contract or purchase order, the supplier is responsible for the performance of all i7:pection requirements as specified herein Except as otherwise specified, the suppiier may utilize his own facilities or any commercial laboratory acceptable to the Government. The Government reserves
14、 the right to perform any of the inspec- tions set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4-92 Classification of Tests. (a) Preproduction Tests (4.4) Provided by IHSNot for ResaleNo reproduction or ne
15、tworking permitted without license from IHS-,-,-MIL-1-23951 13 9779906 O304067 5 I- I MI L-1-2395 1 (WEP) Lots. I 1 - I 4*3 4.3.1 maximum weight of 10 pounds and shall be made with one pelleting press during an 8-hour shift. If more than 10 pounds of pellets are produced in 8 hours, then two or more
16、 sublots shall be made up. Ignition pellet production from each press Sublot Size. -A sublot of ignition pellets shall consist of a I shall be kept separate. Lot Designation. -Beginning with the first sublot of ignition I 4=3.2 pellets produced under a specific contract or order, the lots shall be n
17、umerically identified by master and sublot designations. A change in the master lot number shall occur any time that a new batch of any chemical component is employed and I the sublot designation numbering shall be started all over. I 4.5 Qualitv Conformance Insriections. -The following procedures 1
18、 shall be used for determining that the requirements of this specification have been met. 4.5.1 Sampling. -A minimum of three grams of the ignition pellets shall I be drawn from each of five widelyseparated places from each sublot produced. I The entire sample except 35 ignition pellets shall then b
19、e cut, shaved, or other- wise reduced in size and thoroughly mixed such that any sample withdrawn for acceptance tests will be representative of the entire sample. The 35 pellets shall I be used for the determination of density. 4.5.2 Chemical Composition. -The vendor is required to certify that the
20、 I chemical composition of the pellets furnished are in accordance with BuWeps I Drawing No. 25 16382 (See 6.2). 4.5.3 Average Calorimetric Value. -The calorimetric value for the heat of reaction of the ignition pellet shall be determined in duplicate on each sublot using a Parr bomb calorimeter No.
21、 1200 or equal. A charge of 12 to 18 pellets shall be placed in the bomb and the system purged of any residual air using nitrogen, argon, orhdiumIias. The bomb shall be closed after purging so that an atmosphere _- 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
22、e from IHS-,-,-I :- - of inert gas is maintained in the bomb at atmospheric pressure. The pellets shall I 4.5.4 Average Crush Strength. -The load required to crush the ignition kch sublot. This test shall be made using F. J. Stokes Machine Company pellet hardness tester or equal. The load shall be a
23、pplied in 1000 gram increments along the longitudinal axis and shall be maintained for a minimum of five seconds before increasing the load. Failure to comply with requirements of Table I shall be cause for rejection of the sublot. 4.5.4.1 Alternate Procedure for Determining Crush Strength. -Test pe
24、llets - 1 to 15 pellets from 4.5.5 Dimensions. -The length and diameter of ten randomly selected 1 Table I shall be cause for rejection of the sublot. iecked. Failure of the pellets to meet the requirements of 4.5.6 Average Ignition Pellet Weight and Densityy, -The average weight ups of 15 to 20 pel
25、lets each determination of loss of weight in a liquid medium or (b) determination of weight and volume of liquid displacement. Castor oil is required as the liquid medium. 3. 5.1 level C or as specified (see 6.2). Preservation and Packaging -Preservation and packaging shall be I 5.1.1 the product by
26、 moisture, cormsion, or other foreign matter. Level C. -Preservation and packaging shall be in accordance with ommercial practice to afford protection against damage, contamination of I I I 5.2.1 Level C. -The product shall be shipped in commercial type containers I. - with ICC Code of Federal Regul
27、ations 49 CFR 71-90, and so constructed to withstand normal transportation and handling abuse and must be suitably sealed to prevent contamination of the contents by moisture or foreign matter. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-1-
28、23951 33 W 9999706 0304073 3 MI L-1-2395 1 (WEP) 5.3 Marking. -Unless otherwise specified by the contract or order, unit packages, intermediate packages, and shipping containers shall be marked in accordance with the requirements of MIL-STD-129 and shall include but not be limited to the following (
29、see 6.2): (a) Manufacturers name and address (b) Gross and net weights (c) Lot number and date of manufacture (d) The number of this specification (e) Safety precautions or unusual storage requirements (f) Purchase order or contract number 6. NOTES 6.1 Intended Use. -The material covered by this spe
30、cification is intended for use in the igniter Mk 265. 6.2 be limited to the following information: Ordering Data. -Procurement documents shall specify but not (a) Title, number, and date.of this specification (b) Type and size of container desired (c) Place of inspection (d) Minimum lot size, if app
31、licable (e) Place of delivery (f) Request for copies of inspection data, if source inspected (9) Selection of applicable levels of packing and packaging (see 5.1 and 5.2) (h) Marking requirements (see 5.3) ed (see 4.5.2) b 6 Provided by IHSNot for ResaleNo reproduction or networking permitted withou
32、t license from IHS-,-,-MIL-1-23951 13 9999906 0304072 5 mw - 6.3 between this specification or any specifications, publications or drawings listed herein, shall be referred in writing to the procuringactivityor appointed agent for interpretation and clarification. Conf I icting Requirements . -Conf
33、I ic ting requirements arising 6.4 referenced specifications, materials, applicable drawings, or processes shall be forwarded to the procuring activity prior to manufacture of the affected item or items. All deviations shall be limited to the contract under which they were granted. Request for Devia
34、tion. -Request for deviation from this or 6.5 Request for Waiver. -Request for waiver from this specification, applicable drawings, specificatiom , materials, or processes shall be forwarded to the procuring activify. Waivers shall be limited to the specific units for which they are granted. A waive
35、r request shall include the following: (a) Exact nature of defect (b) CD number and. defect classification (c) Quantity of items involved 6.6 Value Engineering. -All manufacturers of units covered by this specification are encouraged to submit value engineering proposals to the procuring activity in an effort to reduce cost. 6.7 Safety Precautions. -This is a potentially dangerous product. All detailed safety precautions shall be strictly observed as set forth by the manufacturer and user. 7 i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
