1、M I L- I.-8 I 007 (WEP) 15 APRIL 1964 MILITARY SPECIFICAT ION INTEGBATED ELECTF1ONIC CENTRAL AN/ASQ-S6A This specification has been approved by the Bureau of Haval Weapons, Department of the Navy 1. SCOPE 1.1 Scope - The Electronic Central covered by this specification shall provide com Aircraft, In
2、stallation of Electronic Equipment, Aircraft, General Specificztion for Testing, Environmental, Aircraft Electronic Equipment Interference Control Requirements, Aircraft Equipment Control Panel: Aircraft Equipment, Rack or Console Mounted Meter, Time Totalizing Radar Identification Set AN/.4PX-6B Co
3、der Group AN/RPA-89 Indica tor, Cour se ID-3P7/ARN Electronic and Electrical Equipment and Associated RepaFr Parts, Preparation for Delivery of Test Procedures; Freproduction and Inspection, Aircraft Electronic Equipment, Format for Nomenclature and Mameplates for Aeronautical Electronic and Associa
4、ted Equipment Receiving Set, Radio AN/ARR-rlO Electronic Modules, General Specification fox 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-kilitary MIL-N-22239 MIL-A-22669 EIL-C-22670 MIL-C-23672 LIIL- !A-22673 MIL-R-23078 KIL-E- 23 094 A1L-A-G 1-
5、08 .;IL-C-E1009i STAiDARDC Military MIL-STD- 1:s-17322 2.2 3. REQUIREI.IENTC 3.1 MIL-1-81007 (ZEF ) NFvigat ional set, TACAK AK/ARN-52( V ) Pmplifier-Po:*:er Sunply-Receiver Af.:-2?10/ASQ and Antenna AS-QC9/A2A-48 Control, RFdio Set C-279C. I?.RC; Indicator, Frequency Channel ID-758 / ,Ci.?C; Kounti
6、ng MT-2141/fGC and Si.itching Unit cA-629/ARC Coder-Keceiver-Transciitter KY-5331ASQ k!ounting-Plenum C:T-2243/ASQ-56 Receiver-Transmitter, Radio RT-54.2/ASQ Reliability Assurance for Froduction Acceptance oi-Avionics Equipment Ada p t e r , :Ao unt i ng ?.ZIX-4773/ASQ-56A Control, Sadio Set C-4684(
7、*)/ASQ-56A Electric Foxer, Aircraft, Characteristics and Utilization of Leter, Time Totalizing Miniature 400 Cycle, Diuital 04 Availability of Documents (1) Ehen requesting specifications, standards, drawings, and publications, refer to both title and number. Copies of this specificztion and aGFlica
8、ble specifications required by contractors in connection with specific procurement functions may be obtained upon application to the Commanding Officer, Naval Supply Depot, Code KI, 56C1 Tabor .Avenue, Philadelphia 20, “nnsylvania. Parts and hlaterialc - In the selection of parts and materials, fulf
9、illment of major design objectives shall be the prime consideration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL- 1-81007(lfiEP) In so doing, the following shall govern: (1) Parts and material requirements shall conform to Specification MIL-E
10、-5400, (2) Nonrepairable subassemblies, as outlined in Specifica- tion MIL-E-5400, shall be used when practicable. The general size of the subassembly and the amount of circuitry to be included therein shall be approved by theprocuring activity. Nonrepairable subassemblies must be reliable (See 6.6.
11、) (3) When previously produced model s of these centrals did not use nonrepairable subassemblies, the design shall not be changed to employ nonrepairable assemblies without the approval of the procuring activity. 3.101 Nonstandard Parts and Material Amroval - Approval for the use of nonstandard part
12、s and materials shall be obtained as outlined in Specification MIL-E-5400. 3.1.2 Electron Devices - Electronic tubes, transistors, and diodes shall be chosen and applied, and the complements reported as outlined in Specification MIL-E-4682. procuring activity for review and approval prior to preprod
13、uction testing. The complement report must be submitted to the 3.2 Desicin and Construction 3.2.1 General - The central shall conform with all the applicable requirements of Specification MIL-E-5400 for design, construction, and vrorkmanship unless otherwtse specified herein or in the individual equ
14、ipment specifications. 3.2.2 Total Yieiaht - The total weight of the central, excluding cables, shall be a minimum consistent with good design and shall not exceed 240.5 pounds. 3.2.3 Modular Construction - The use of modular space assignment and construction of easily disconnected plug-in subunits
15、of component assemblies shall be in accord withspecification MIL-E-19600 where possible. The following considerations shall apply where practicable. (1) Modules shall be of standardized form and dimensions to facilitate use in other equipment of different over-all configuration and shall be designed
16、 for maximum practical effectiveness of cooling air supplied by or to the equipment. 4 I -I*- -. I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-81007 (WP ) (2) Each module shall contain the circuitry of one or more functions of the equipment
17、 to facilitate testing and repair. into as many modular units as is electrically and physically practical in keeping with efficient space utilization, equipment performance, and reliability. It shaU be posslble to operate the equipment with one or more modules removed from the chassis but connected
18、to it electrically by means of one or more and Connections 3.2.5.1 Cables and Connectors - The central shall provide for the use of cables and connectors in accordance with Smcification KIL-E-sbOO unless otherwise specified in the individual equipment specifications. Provided by IHSNot for ResaleNo
19、reproduction or networking permitted without license from IHS-,-,-MIL-I-81007(KEP) of satisfactory operation using external wiring in accordance with the applicable requirements of Specification MIL-2-5088, The external wiring shall be unshielded, except that a minimum number of the individual wires
20、 may be shielded when demonstrated as necessary to meet interference control requirements and provided the assembly of the cable to its plup may be accomplished easily. attached to the cables shall not be supplied as part of the centrals, 3.2.5,2 Interconnection Cablinq - The central shall be capabl
21、e External cables and that portion of the connectors 3.2*6 Solderina (Electrical Connections1 - Secure mechanical connections shall not be required before soldering small lightweight parts to printed wiring assemblies provided central performance is not compromised. 3.2.7 Interchanaeabilitv of Reord
22、ered Eauiwrnent - For reordered equipment interchangeability shall exist between units and all replaceable assemblies, subassemblies, and parts of a designated model of any previously manufactured equipment, supplied or designated by the procuring activity. Interference Control - The generation of r
23、adio e 3,2.8 interference by the central and the vulnerability .of the central to radio interference shall be controlled within the limits of Specification MIL-1-6181 unless otherwise specified in the individual equipment specifications. 3.2.9 Maintenance wrovisions and Field Testinq - Provisions fo
24、r maintenance shall be as specified in Specification MIL-E-5400. test points and test facilities shall be provided to the greatest extent practicable for ease of field testing and maintenance. Specific 3.2.10 Nomenclature and Nameplates - Nomenclature assignment and nameplate anproval for equipment
25、identification shall be in accordance with Specification MIL-N-18307. (See 6.4, ) 3.2.11 Standard Conditions - The following conditions shall be used to establish normal performance characteristics under standard conditions and for makng laboratory bench tests, Temperature Room ambient (2525OC Al ti
26、 tude Normal ground Vibration None Humidity Input Power Voltare System Cooling Air Room ambient up to* 90 percent relative humidity- 115 k1.0 v a-c, 3 phase 26 kl.0 v a-c,1 phase 27.5 2.5 v d-c 132 lb per hour 3.2.12 Service Conditions - The central shall operate satisfactorily under any of the envi
27、ronmental conditions or reasonble combination of.these conditions as specified in Specification MIL-E-5400 for the classes of equipment as specified herein unless otherwise specified in the individual equipment specification. 6 : Provided by IHSNot for ResaleNo reproduction or networking permitted w
28、ithout license from IHS-,-,-NIL-1-81007 58 = 9777906 OL677LI7 Lt Receiver-Transi?itter, Radio Receiver-Transmitter, Radio Coder-Receiver-Transmitter Amplifier-Power Supply-Receiver Antenna Mounting-Plenum Ad apt er -fr!ou nt i ng Control, Radio Set Switching Unit Mounting Indicator, Frequency Channe
29、l Control, !?adio Set Class 2 Class 3 Class 2 Class 2 Class 2 Class 2 Class 2 Class 1 Class 2 Class 2 Class 1 Class 1 3.2.12.1 Central Coolinq Air Requirements - The central cooling air requirement is given in fiaure 1 of this specification. 3.2.12.2 Vibration - The central shall operate satisfactor
30、ily when subjected to the vibration requirements of curves I and II of Specification MIL-E-5400. 3.2.13 Warmur, Time - The time required for the central to warm up prior to operations shall be kept to a minimum and shall not exceed 5 minutes under standard conditions, and 15 minutes at extreme servi
31、ce conditions. Primary Inout Power Reauirements - The central shall meet all appliczble requirements of MIL-STD-704 unless otherwise specified herein and shall give specified oerformznce from the follorling power sources with characteristics as desincd in MIL-CTD-704 having limits as specified there
32、in. amounts. 3.2.14 The power required by the central shall not exceed the specified (1) A-C Power, Three-phase, 115/200V, Category “By“ 900 VA. (2) A-C Posver, Single Phase, 26 V, iithin Limits Proportional to Czkegory “Di: 1.25 VA.* (3) D-C Power, 28 V, Category “By“ 4.5 Amp Xominal. (Additional c
33、urrent requirements of 6 to 8 amperes per equipment while channeling. 3.2.15 Control Panels - ,411 rack or console mounted control panels shall conform to the applicable requirements of Specification MIL-C-6781. The configuration of all control panels must be approved by the procuring activity prior
34、 to preproduction testing. *Includes typical system instrumentation. *- 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-81007 58 W 77779Ob 016974 b ?“?IL- 1-81007 (VEP ) 3.3 Detail Reauirements 3.3.1 Communication Function - The comunication
35、function shall be performed by Receiver-Transrnitter, Radio, IiT-542/ASQ in accordance vri th Specification MIL-R-22678. performed by Receiver-Transmitter Radio RT-384/ARN-52(V) in accordance with Specification MIL-N-2223%. 3.3.2 TACAN Function - The navigation function shall be 3.3.3 AI- The auxili
36、ary receiver, power supply, and automatic direction finder function shall be performed by. Amplif ier-Power Supply-Receiver AtA-2310/ACQ and Antenna AS-909/ARR-48 in accordance with Specification MIL-A-22669* 3.3.4 performed by the Coder-Receiver-Transmitter KY-53b)lASQ in accordance with Specificat
37、ion MIL-C-22672 touch tuning control with remote channel and frequency indicator function shall be performed by Contrcl, Radio Set C-2790/ARC; Switching Unit SA-629/ARC; Mounting ELT-2141/ARC and Indicator, Frequency Channel ID-758/ARC in accordance with Specification MIL-C-22670. the operation of t
38、he TACAN shall be performed by Control, Radio Set C-4684/ASQ-56A in accordance with Specification MIL-C-81009. Mountin -Plenum - The mounting-plenum function for the Integrated Electronic Central-A shall be performed by Mounting-Plenum IlTT-2243/ASQ-56A in accordance with Specification MIL-Id-22673.
39、 the Integrated Electronic-56A shall be performed by Adapter, Mounting MX-4773/ASQ-56A in accordance with Specification MIL-A-81008. Associated EauiDment - The central shall operate with the-following associated equipment which shall not be supplied as part of the central . IFF/Coder Function - Th I
40、FF/coder function shall be 3.3.5 1 The communication 3.3.6 TACAN Control - The remote control function recuired for 3*3*7 3.3.8 hlountln -Ada ter - The mounting-adapter function for 3*4 3.4.1 Auxiliary Receiver ControA - The remote control function required for the operation of the auxiliary receive
41、r shall be per- formed by Control, Receiver C-1457iAHR-40 of Receiving Set, Radio AN/ARR-40 in accordance with Specification MIL-R-18400. 3.4.2 IFF Control - 7?-ie remote control function required for the operation of the IFF shall be performed by the Control, Radar Set C-ll59/APX-6B of Radar Identi
42、fication Set d/APX-6B in accordance with Specification MIL-R-7893. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-I-L007 58 9997706 O367747 8 = MIL-1-81007 (HEP ) 3.4.3 Coder ControL - The remote control function required for the operation of
43、the Coder shall be performed by Control, Radar Set C-l272A/Ar?A-89 of Coder Group AN/APA-89 in accordance with Specif icatioh MIL-C-7953. 3.4.4 T.4CAN Indicator - The indicator function required for the remote operation of TACAN shall be performed by Indicator, Course ID-387/ARN in accordance with S
44、pecification MIL-1-9229. 4. QUALITY ASSURANCE PRCVISIONS . L in of 4.1 ResDonsibility for InsDection - Unless otherwise specified the contract or puxhase order, the supplier is responsible for the performance all inspection requirements as specified herein. Except a5 otherwise specified, the supplie
45、r may utilize his own facilities or any commercial laboratory acceptable to the government. only at the inspections set forth in,the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. The government reserves the right to perf
46、orm 4.1.1 Classification of Tests - Items oavered by this specification ch911 be subjected to the following tests to determine compliance with all applicable requirements. (1 1 Preproduction Tests (2) Production Sample Tests (3) Acceptance Tests (4) Life Tests 4.2 Premoduction Tests - Preproduction
47、tests shall be made on one or more individual equipments and centrals representative of production equipments and centrais (see 4.2.3) to be supplied under the contract. Preproduction tests shall consists of the following: (i) Contractors Demonstration Test (2) Service Approval Tests 4.2.1 Contracto
48、rs Demonstration Tests - Contractors demonstration tests shall be accomplished under the responsibility of the contractor and shall be conducted in accordance with the approved test procedure of 4.6. submitted to the procuring activity for review and approval prior to shipping the quipments to the s
49、pecified destination for seryice approval tests. The government inspector and the procuring activity shall be advised when tests are to be conducted so that a representative may be designated to witness or supervise the tests when so desired. to conduct all required tests shall obtain the services of a comercial testhg 1 abor atory. Data obtained by the contractor in conducting these tests shall be Cont$actors not ha
