1、HIL-I-82265B (3) 72 7777906 0242730 7 M MIL-I-82265B(NU) Amendment-1 29 September 1980 MILITARY SPECIFICATION INSECT BAR, COT TYPE, NYLON NETTING This amendment forms a part of Military Specification MIL-I-82265B(NLJ), dated 13 December 1979, and is approved for use by all Departments and Agencies o
2、f the Department of Defense. Page 3 3.3.2,. Delete in its entirety and substitute: - “3.3.2 Cloth, oxford, nylon be nylon oxford cloth, 3 ounce, olive green 106, conforming to type 1, The material for the extension pieces shall Class 1, of MIL-C-508; optional seam type. The cut edges of the cloth sh
3、all be fused for Page 5 Table I, Operation l(a) - Line 2, 3, and 4 Delete and add “two side panels, two end panels, two extension pieces, ten“. Operation l( c) Delete “dimentions“ and add “dimensions“. ( Operation 3, Columns Stitch Type and Seam and Stitching Type add: “401 and LSa-2“. Page -6 Table
4、 I, Operation 4, Delete in its entirety and.substitute: “4. Prepare top panel Position two extension pieces of nylon oxford (see 3.3.2) as shown in Figure 1. gauge to the netting with.the outer row of stitching to be no less than 1/16 inch from edge. Join each extension piece 1/4 to 5/16 inch , 301
5、LSC-2 -9-12 . B B or 401 LSa-2 B A“ . FSC 7210 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-I-82265B (3) 72 7977906 0292733 9 MIL-I-82265B(NU) Amendment-1 Page 6 (contd) Table I, Operation 5(a) Delete in its entirety. Page 7 Table I, Operatio
6、n 5(b) Table I, Operation 6(a) Delete in its entirety. Table I, Operation 6(b) Line 2 - After “10“ add I(? 1/2)“. Line 2 - After “10“ add “(k 1/2)“. Table I, Operation 6(c) Delete in its entirety. Table I, Operation 7 - Delete in its entirety and substitute: “7. Closing of insect bar a. and binding
7、together or as an alternate, stitch both panels together without binding. Position top panel and side panel, and stitch both panels 301 BSa-1 9-12 B or LSC-2 B 401 LSa-2 B B B A b. panel and stitch (top, side, and end panels) and binding together in one continuous operation. NOTE: Position the combi
8、ned (top and side) panels to end The top ends of the vent opening seams shall be caught in the binding stitching. 301 BSa-1 9-12 B B“ . -* Page 8 Table I, Operation 8(a)-Add new sentence: “The six (6) top tie tapes shall be attached from the top side of the top panel thru the binding.“ . Table I, Op
9、eration 8(b) Line 4 - Delete “Seamed“ and substitute “Stitched“. Table I, Operation 8(b) - Stitches per inch add “20-“. .Table I, Operation 11 - Finish measurement - Delete in its entirety. Page 2 of 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
10、4 MIL-1-822658 (3) 72 = 777770b 0242732 O MIL-I-82265B(NU) Amendment-$ Page 11 Defect PANELS - A. Top (2) add: “When optional seam type is used“. Page 12 Defect CORNER REINFORCEMENT Delete in its entirety. Defect TIE TAPES add new defect: “c. Not located as specified“. Minor Page 16 Figure 1 - Delet
11、e and substitute new figure 1. . Custodian: Preparing Activity: Navy - Nu Navy - Nu Review Activity: Navy - MS DLA - CT Project No. 7210-N248 User Activity: Navy - YD, CG, MC ( Page 3 of 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-r, #a- II . N
12、OTE: - I II I I I I OPTIONAL Seam tE for A-A & B-B !see note) I ENDS AND SIDES OF BAR SHALL BE NO LESS THAN 34.INCHES IN HEIGHT. TOLERANCE FOX OVERALL LENGTH, WIDTH AND HEIGHT DJHENSIOWS SHALL BE - i- 1 INCH AND ALL OTHER DIMENSIONS %1/4 INCH. OPTIONAL STITCHING HAY BE USED WEN SELVAGE OR FUSED EDGES ARE USED- *UA. GOVERNMENT PRINTING OFFICE: IPO-OI-OZJIP ?age ,4 f 4 9 _ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
