1、MIL-M-L07A 17 W 7799706 Oq2907L 9 i MIL-M-81807A(AS) -_ 22 February 1971 Supercedi n 21 December 1970 7 MIL-M-8180 (AS) MI LI TARY SPE CI FI CATI ON Marking of Aircraft Ground Support Equipment and Other Flight Line Vehicles with Retro-Reflective Materials; process for This specification has been ap
2、proved by the Naval Air Systems Comnand, Department of the Navy 1. SCOPE 1.1 This specification prescri bec general requirements for the marking of aircraft ground support equipment and other vehicles (-.e., runway sweepers, firetrucks, refulers, etc.), used on or near the flight line area with retr
3、o-reflective materials, 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue ineffect on the date of invitation for bid or request for proposal, form a part of this specification to the extent specified herein, SPEC1 FI CATIONS FE DE RAL L-S-300 TT-C-001060 Coating, Mixture, Reflective L
4、iquid TT-V-1 O9 Varnish, Spar, Alkyd-resin Sheeting and Tape, Reflective: Non-exposed Lens, Adhesive Backing (When requesting applicable documents, refer to both title and number. Copies of unclassified documents may be obtained from the Comnanding Officer, Naval Publications and Forms Center, 5801
5、Tabor Avenue, Philadelphia, Pennsylvana 19120). Licensed by Information Handling ServicesMIL-M-LO7A L7 M 777790b Oq27072 O M I L-M -8 180 7A(A S ) 3. REQUI REMENTS or drawings, aircraft support equipment and other flight line vehicles shall be marked with reflective tape conforming to L-S-300, Type
6、II, Class 3, Reflectivity No. 1, Color g, Width 2 inches. be applied along the extreme perimeter of the equipment to reflect its general outline configuration, when operating under reduced lighting conditions. When possible, the tape shall be applied to delineate the entire perimeter of the equipmen
7、t. surfaces containing compound curves at the corners or large rivets, nuts, bolts, etc. need not be marked in these particular areas provided the marking provides a general outline of the equipment. Application of the reflective material shall not obliterate other markings (i .e., cau- tion, capaci
8、ty, danger, name plates, servicing/safety instructions, product marking, etc.). Wheel chocks, tie downs and other small equip- ment whose configuration does not readily lend itself to the application of reflecti ve tape shall be marked with 2 inch circular stripes of reflective paint (i .e., wheel c
9、hocks shall be marked around the middle and each exposed end). The paint shall conform to the requirements of Speci fi cati on TT-C-001060, Col or No. 721 1. 3.1 General : When specified in contracts, orders, specifications The tape shall However, equipment having perimeter 3.2 Marking Procedures :
10、3.2.1 Surface Preparation: will be appiied shall be cleaned posits of cleaning compounds sha thoroughly dried. 3.2.2 Amlication: Amlv i The surface to which the tape or paint . of all loose scale and dirt; all de- l be removed. The surfade shall be accordance with the manufacturers instructions. Ins
11、ure that il: air bubbles are removed when tape is applied. Do not apply at temperatures below 5OOF. NOTE: Do not oven bake equipment after the reflective material has been applied. applied to the edges of the tape in the form of a fillet to protect the tape. 3.2.3 Sealer: Sealing compound conforming
12、 to TT-V-109 shall be 3.3 Workmanshi : The reflective material shall not be haphazardly applied and 71-4 s all be free from ragged edges, viods, cracks, scales, air bubbles, blisters or dirt. 2 Licensed by Information Handling ServicesProject No. 1730-N i42 U. S. GOVERNMENT PRINTING OFFICE: 1971 -433-696/5400 3 Licensed by Information Handling Services
