1、XIL-P -2 3s 83A (XC ) 13 September 1987 SUFEKSEDING MIL-I-28983(LIC) 10 May 1972 MILITARY SPEC IF KATION POLE, BEACH, PANEL MARKER: KETAL This specification is approved fol use by U. S. Marine Crops, Department of the Navy, and is available for use by all Departments and Agencies of the Department o
2、f Defense, 1. SCOPE 1.1 This specification covers requirements for one type of beach pole. 2. APPLICABLE DOCUblENTS 2.1 Government documents. 2.1.1 Specifications, standards and handbooks. Unless otherwise specified, the following specifications, standards, and handbooks o the issue listed in that i
3、ssue of the Department of Defense Index of Specifications and Standards (DODISS) specified in the solicitation form a part of this specification to the extent speciEied herein. SPECIFICATIONS FE DERAL PPP -T-5 3 -Tape, Packaging, Waterproof MILITARY YIL-C-16 173 -Corrosion Priventive Compound, Solve
4、nt MII,-E-52 7 9 8 -Enamel, Alkyd, Camouflage MIL-C-52950 -Crate, Wood, Open and Covered. Ciitback, Cold-application. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to the Commandant of the Marine
5、Corps (LXA-1), Headquarters, U. S. Marine Corps, Washington, D. C. 20380, by using the self-addressed Standardization Document Improvement Proposa 1- (DD Form 1426) appearing at the end of this document or by letter. FSC 8345 THI DOCUMENT CONTAINS /8 PAGES. Provided by IHSNot for ResaleNo reproducti
6、on or networking permitted without license from IHS-,-,-MIL-P-28783A 3 M 777790b 0386857 O m - MIL-P-28983A(MC) STANDARDS FEDERAL FED-STD-66 -Steel Chemical Composition And Harden- ability. MIL TTARY MITrSTD- 105 -Sampling Procedures And Tables For MIL-STD-129 -Marking For Shipment And Storage. Insp
7、ection By Attributes. 2.1.2 Other Government documents, drawings, and publications The following Government documents, drawings, and publications form a part of this specification to the extent specified herein. DRAWINGS MARINE CORPS 71C5045A0000 -Pole, Beach, Panel Marker: Metal; 71C5045A0001 -Pole
8、, Reach, Panel Marker: Metal; Assembly And Details. Details. (Copies of specifications, standards, handbooks, drawings, and publications required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting offi
9、cer). 2.2 Other publications. The following document(s) form a part of this specification to the extent specified herein. The issues of the documents which are indicated as DoD adopted shall he the issue listed in the current DoDISS and the supplement thereto, if applicable. ASTM-A-512-79 -Tubing, M
10、echanical, Cold Drawn, Buttweld, Carbon Steel. (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103). UNIFORM CLASSIFICATION COMMITTEE Uniform Freight Classification Rules (Application for copies should be addressed t
11、o the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606). (Industry association specifications and standards are generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies). Provided by I
12、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-28983A 83 7997906 0386858 2 3. REQUIREMEMTS 3.1 Samples. Samples are Eurnished solely for guidance and information to the contractor. Variation from this speciEication may appear in the sample, in which case t
13、he specification shall govern. 3.2 First article. Unless otherwise specified (see 6.2) before production is commenced, a finished beach pole with components shall be submitted, or made available to the contracting officer or his authorized representative for approval. The approval of the first artic
14、le authorizes the commencement of production, but does not relieve the contractor of responsibility for compliance with applicable provisions of the specification. The first article shall be manufactured by the contractor in the same facilities to be used for the manufacture of the produc tion i tem
15、s . 3.3 Materials. 3.3.1 Tubing. The upper and lower pole sections shall be made Eroin carbon stenechanical, but twelded, cold drawn, conforming to ASTM-A-512-79 and Drawing No. 71C5045A0000, Two sections of tubing are required for the beach pole. 3.3.2 Cap-clamp. The cap-clamp shalL he made of stee
16、l-strip, mild, No, 16 gage (0.065) comforming to the requirements on Drawing No. 71C5045A0001. One cap-clamp is required for the beach pole. As an alternate, an adjustable clamp (see 3.3.7) may be used in place of the cap-clamp. 3.3.3 Eye-bolt collar. The collar for the eye-bolt shall he made from c
17、arbon steel, mechanical, buttwelded, cold drawn, conforming to ASTM-A-513-79 and Drawing No. 71C5045A0001. One collar for the eye bolt is required for the beach pbie. 3.3.4 Bushing. The bushing shall be made froin steel, round, cold finished, AISI-C1018 conforming to FED-STD-66, and the requirements
18、 on Drawing No. 71C5045A0001, One bushing is required for the beach pole. 3.3.5 Hinge bar (upper and lower). The hinge bar for the lower and upper sections of the pole shall be made from steel, round, cold finished, AISI-C1018 conforming to FED-STD-66 and the requirements on Drawing No. 71C5045A0001
19、. One lower and one upper hinge bar are required for the beach pole. As an alternate to welding the upper hinge bar to upper tube, they may be asseinbled by drilling a 3/16-inch hole, 3/4-inch from upper end of tube (part No. 2) and inserting a 3/16 x 1 5/32-inch long semitubular rivet. 3.3.4 Hinge-
20、strip. The hinge-strip connecting the upper hinge bar to the lOk7er hinge bar shall be made from steel strip, hot rolled, conforming to the requirements on Drawing No. 71C5045A0001. One hinge strip is required for the beach pole. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted
21、 without license from IHS-,-,-MIL-P-28983A 83 m 7999906 0386859 4 MIL-P -2 8983A( MC) 3.3.7 Adjustable clamps. The adjustable clamps shall be made from steel strip, mild, No. 16 gage (0.065) conforming to the requirements on Drawing No. 71C5045A0001. Five adjustable clamps are required for the beach
22、 pole. 3.3.5 Stud. The stud shall be made Erom steel, round, cold finished AISI-C1018 conforming to FED-STD-66 and the requirements on Drawing No. 71C5045A0000. One stud is required or the beach pole. 3.3.9 Saddle plate, The saddle plate shall be made froin steel, mild conforming to the requirements
23、 on Drawing No. 71C5045A0000, One saddle plate is required or the beach pole. 3.3.10 Stake. The stakes shall be made from steel, hot rolled AISI-C1015 coming to FED-STD-66 and the requirements on Drawing No. 71C5045A0000. A closed lance may be used in place of the link (part No. 23) on each stake fo
24、r attaching the chain. Three stakes are required or the beach pole (one short stake welded to the saddle plate and two longer stakes for supporting the pole). - 3.3.11 Snap, hook, swivel eye. The hooks shall be made from steel, galvanized finish, contormina to requirements on Drawing No. - - 71C5045
25、A0000. Six snap hooks are required for the beach pole. 3.3.13, Eye bolt with square nut. The eye bolt and square nut shall be made from steel galvanized finish, conforming to requirements on Drawing No. 71C504A0001. One eye bolt with square nut is required for the beach pole. As an alternate, a 1/4-
26、inch-diameter, round eye bolt nay be used. This will necessitate the drill.ing of a 1/4-inch hole through the upper pole in lieu of a 7/32-inch hole. In addition, this hole will be drilled from the same side as the 1/4-inch hinge pin hole at the lower end of the upper pole section, The eye bolt, wit
27、h nut, may be packaged separately with cables attached in lieu of being assembled on the pole section. 3.3.13 Screw with square nut. The machine screw with square nut shall be made from steel, galvanized finish conforming to requirements on Drawing No. 71C5045A0001, Five screws with square nuts are
28、required for the beach pole. 3.3.14 Hinge pins. 3.3.14.1 Upper pin. The hinge pin for attaching the hinge strap to the upper hinge bar shall be a roll pin, 3/16-inch diameter by 1-inch long. 3.3.14.2 Lower pin. The hinge pin for attaching the hinge strap to the lower hinge bar shall be a roll pin, 3
29、/16-inch diameter by 3/4-inch long. 3.3.15 Wire rope. The preformed wire rope shall be made from steel, galvanized finish having 6 strands of 7 wires in right regular lay around a fiber core with a minimum breaking strength of 1200 pounds. The diameter shall be 1/8 inch. Two 17-foot lengths are requ
30、ired for the beach pole. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-28983A 3 W 9999906 0386860 O m MIL-P -2 89 8 3A (MC) 3.3.16 Clamps. The clamps for the wire rope shall be made from aluminum and shall be swaged sleeves, 314 inch to 1-1
31、14 inches long to fit the 1/8-inch wire rope. Two clamps are required for the beach pole. 3.3.17 Connectors. The connectors or the wire rope shall be made from steel, having a galvanized finish similiar or equal to the “Stanley (pull tite clamp)“ as illustrated on Drawing No. 71C5045A0000. The conne
32、ctors, when assembled to the wire rope, shall withstand, without failure or damage, a load equal to the breaking strength of the wire rope. Two connectors are required for the beach pole. 3.3.18 Chain. The chain for attaching the connector to the stakes shall be steel single jack chain, 1/8-inch dia
33、meter links, hiving a galvanized finish. beach pole. TWO lengths, 6 2112 inches, are required or the 3.3.19 - Link. The link for attaching the chain to the stake shall be made from steel, 3/16-inch round, AISL-Cl018 conforming to FED-STD-66. The ends, when set in place, shall he peened and welded as
34、 illustrated on Drawing No. 71C5045AOOOO. One link is required for each of the long stakes. As an alternate, a closed lance may be cut in each stake, 3/4 inch from the upper end (see 3.3.10). 3.4 Design. The beach pole shall he the U. S. Marine Corps design shown on Drawing Nos. 71C5045A0000 and 71C
35、5045A0001 except as modified by this specification. The pole shall be collapsible, equipped with cap collar (or a clamp), clamps, guy wires, hooks, etc., or attaching the panel marker and erecting the pole, but does not include the panel marker. 3.5 Construction. The construction of all components a
36、nd the assembly of the beach pole covered herein shall conform to the requirements of this specification and Drawing Nos. 71C5045A0000 and 71C504A0001. 3.6 Finish. The hinge strip and hinge bars shall have a cadmium plated finish; the wire ropes shall be steel with a galvanized finish; wire rope cla
37、mps, eye bolt with nut and machine screw with nut shall be cadmium or zinc. coated and not enameled finish. All other steel parts shall have a honderized, or equal, undercoating and a finish coat of enamel, color forest green lusterless conforming to MIL-E-52798. 3.7 Workmanship. The finished and as
38、sembled beach pole shall conform to the quality and grade of product established by this specification. The occurrence of defects shall not exceed the applicable acceptable quality levels .( AQL). 4. QUALITY ASSURANCE PROVISIONS 5 Provided by IHSNot for ResaleNo reproduction or networking permitted
39、without license from IHS-,-,-MIL-P-28783A 83 973930b 0386861 2 4.1 Responsibility for inspection. IJnless otherwise specified in the contract or purchase order, the contractor is responsible or the performance of all inspection requirements as specified herein. Except as otherwise specified in the c
40、ontract or order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, iinless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such
41、inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Certificate of compliance. When certificates of compliance are permitted, the Government reserves the right to check test such items to determine the validity of the certification. 4.2 Classifi
42、cation of inspection. The inspection requirements specified herein are classified as follows: First article inspection (see 4.4). Quality conformance inspection (see 4.5). 4.3 Inspection conditions. Unless otherwise specified herein, all inspections shall be performed in accordance with the provisio
43、ns set forth in MIL-STD-105. 4.4 First article inspection. When first article is required, inspection shall be performed on a completely fabricated beach pole with components for conformance to all provisions of this specification. 4.5 Quality conformance inspection. 4.5.1 Testing of components. In
44、accordance with 4.1 above, components and materials shall be tested in accordance with all requirements of referenced specifications, drawings and standards, unless otherwise excluded, amended, modified or qualified in this specification or applicable purchase documents. The supplier shall furnish a
45、 certiEicate of compliance for the material and finish requirements described in this specification. 4.5.2 In-process inspection. Inspection shall be made during the manufacture of the end item to ascertain that the following operation is performed as specifed herein. The Government reserves the rig
46、ht to exclude from consideration for acceptance any material or service for which in-process inspection has indicated nonconformance. Operation or assembly Requirement paragraph Treatment of metal parts 3.6 prior to painting 6 Provided by IHSNot for ResaleNo reproduction or networking permitted with
47、out license from IHS-,-,-MIL-P -2 8983A( MC) 4.5.3 Examination of the end item. The end item shall be examined for the defects listed in 4.5.3.1 and 4.5.3.2. The sample unit shall be one completely fabricated beach pole and components. 4.5.3.1 General defects. General defects shall he classified as
48、f 0lLows : Examine Finish Mat er ia 1 Design Construc tion incorrect; illegible; of improper size, location or method of application. Mat er ia1 s Any component missing. Any component damaged. Workman sh i p Inadequate application of components. Contents Number per container is more or less than req
49、uired. Weight Gross/net weight exceeds requirements. 5. PACKAGING 5.1 Packaging requirements. Packaging shall be level A or commercial as specified (see 6.2). 5.1.1 Level A. All uncoated metal-surfaces of the beach pole and components shall be coated with a thin film, hard drying preservative conforming to grade 1 of MIL-C-16173. Components shall be secured to the beach pole, in a manner designed to restrict movement, by use of reinforced pressure
