1、MIL-P-85LI59 (2) 13 W 7979906 0369830 2 M1L-P-55459(-4S) MILITARY SPECIFICATION PROBE, CRUSH SENSOR, RH, FZU-45/B AND LH, FZU-46/B AND PROBE, AIR PRESSURE, FZU-47/B AMEND!ENT 2 1 ,lUNE. 1987 SUPERSEDING AMENDMENT 1 13 December 1984 This amendment forms a part of Military Specification MIL-P-85459(AS
2、) dated 12 Decenber-l983,-*abd is approved ZQ use withzn Ehe Naval Air Systems Command, Department of the Navy, and is available for use by all Depart- ments and Agencies of th Department of Defense. PAGE 3 Following paragraph 2.1.2, but before “CODE OF FEDERAL WGULATIONS (CFR)“, add “OTHER GOVERNNE
3、NT DOCUHENTS“ . Followingeighth line of paragraph 2.1.2, add “PUBLICATIONS“. PAGE 4 Change paragraph number “3.1.1“ to “3.7*, and “3.1.2“ to “3.8“. PAGE 5 Change paragraph number “3.1.3“ to “3.8.1“. The attached insertable replacement pages listed below are replacements for stipulated pages. When th
4、e new pages have been entered in the document,. insert the amendment as the cover sheet to the specification. Replacement Rase 35 36 Page replaced 35 Reprinted without change R . ;FSC i- 13361 THIS DOCUMENT CONTAINS o PAGES. I AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribut
5、ion unlimited. - e* Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMENDMENT 2 - PAGE 6 Paragraph 3.4.2, third line, delete “end item.“ and substitute -probe.*. Table I title, delete “type“ and substitute “Type“. Table I, fourth and fifth lines, fou
6、rth column, delete “100 Mohms“ and Substitute “50/5 Mohms 5/“; and after footnote 4/ under table, add “S/ SO Mohms applies prTor to the environmentalyincpection sequence; 5-tlohms applies during the environmental inspection sequence .a PAGE 7 Table II title, delete “type“ and substitute “Type“. Tabl
7、e 11, fourth and fifth lines, fourth column, delete “100 Mohms“ and substitute “50/5 Mohms 5/“; and after footnote 4/ under table, add “5/ 50 Mohms applies pryor to the environmental-inspection .sequence; 5-Mohms applies during the environmental inspection sequence. “ PAGE 8 Table III title, delete
8、“type“ and substitute “Type“. Table III, fourth and fifth lines, fourth Tolumn, deIete “100 Mohms“ and substitute “50/5 Mohms A/“; and after footnote 31 under table, add “4/ 50 Mohms applies prior to the environmental-inspection sequence; 5-Mohms applies during the environmental inspectkon sequence.
9、 I PAGE 9 Table IV title, delete “type“ and substitute “Type“. Table IV, fourth and fifth lines, fourth column, delete “100 Mohms“ and substitute “50/5 Mohms 4/“; and after footnote 3/ under table, add “41 50 Nohms applies pryor to the environmental-inspection sequence 5-Mohms applies during the env
10、ironmental inspection sequence. PAGE 10 Table V title, delete “type“ and substitute “Type“. Table V, Add Test 23 with the following switch settings and the following footnote 2: 2f “23 X X O O O O O 6 volts - 2/ - Test voltage to be read 5 seconds after removal of power.“ Provided by IHSNot for Resa
11、leNo reproduction or networking permitted without license from IHS-,-,-PAGE 11 Table VI title, second line, delete “type“ and substitute “Type“. Table VI, Add newTest 6 and Test 8; add footnote 2: change existing Test 6 to Test 7; 21 4 V min - I 6 O00 - 7 TP3 to TP4 1.0 ohm max 8 TP4 to TP5 1.0 ohm
12、max .% Test voltage to be read 5-seconds after removal of power.“ PAGE 12 Change paragraph number “3.7“ to “3 . 9“. Paragraph 4.1.1, second line after test, add “equipment“. Paragrap- 4.1.1.2, third line, delete “at 1eas.t“ and substitute “not less than“. Paragraph 4.1.1.3, third line, delete “3.Ll“
13、 and substitute “3.7“. PAGE 15 Paragraph 4.7 NOTE, third line, delete “4.3.2“ and substitute “4.3.4“. PAGE 16 Paragraph 4.7 . 2. la, second line? after “a“ add “minimum“. Paragraph 4.7.2.1b, first line, after “(A)“ add “minimum“; second line, after “28“ add “fl“. Paragraph 4.7.2.2b, second line, aft
14、er “a“ add “minimum“. Paragraph 4.7.2.2 first line, delete “at 28 Vdc.“ and substitute “minimum at 28 Il Vdc.“. PAGE 17 Paragraph 4.7.3, second line, delete “3.1.1“ and substitute “3.7“. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PAGE 19 Paragra
15、ph 4.7.6.1, second line, following 105.1, add: “either method, except minimum temperature shall be -65F.“ PAGE 20 Paragraph 4.7.6.3.2: Delete paragraph and substitute the following: “4.7.6.3.2 Pyro shock. To determine conformance to 3.4.4.3.2, test * the probe in accordance with the following. trans
16、ient excitation in the primary axis (see Figures 1 and 2) to satisfy in each of the two remaining orthogonal secondary axes consistent with the shock response spectrum shown in Figure 16. applied shock transients shall be between 0.Q2 and 0.15 second. analyses used to determine the shock response sp
17、ectrum shall be performed at a sequence of natural frequencies at intervals uf one sixth octave or smaller. The allowed tolerance shall be within +6 and -3 dB of the specified.acceleration. one twelfth octave shall not exceed +12 and -6 dB from the specified spec t 1: um. Subject the probe to one th
18、e shock response spectrum shown in Figure 16, and one transient excitation t The duration of the The Single peak or notch equal to or less than Paragraph 4.7.6.4, fifth line, aft er “hours“ add “minimum“. PAGE 21 Paragraph 4.7.6.5a. Add to the end of the second line after module: I (inhib it mode) :
19、 Paragraph 4.7.6.5b. Add to the end of the second line after module: “(noninhibit/delay mode) :Ir Paragraph 4.7.7, second line, delete “3.6 and 3.7.“ and Substitute “3.5, 3.6 and 3.9.“. PAGE 22 Paragraph 6.2.lb, delete subparagraph number “b“ and substitute “c“; second line, delete “3.1.1.“ and subs
20、titute 13.7.“. 3 . f Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PAGE 23 Paragraph 6.2.lc, delete subparagraph number “e“ and substitute “d“; second line,delete “3.1.2“ and substitute r3.8.“. Paragraph 6.2.ld, delete subparagraph number “d“ and s
21、ubstitute “e“; second line, delete “3.1.3“ and substitute “3.8.1.“. Paragraph 6,2.le, delete subparagraph number “e“ and substitute “b“; last line after “article“, add “(see 3.2).“. *PAGE 24 Paragraph 6.3.1.1, second line, after “installed“ add “(see 3.4.2.1) .*l. Paragraph 6.3.1.2, third line, afte
22、r “switch“ add “(see 3.4.2.2.1).“. Paragraph 6.3.2, third-line, after “switch“ add “(see 3.4.2.2.2) .l. Paragraph 6.3.3, last line, after “personnel“ add “(see 3.4.2.1 and 3.4.2.2) .l. Paragraph 6.3.4, last line, after “time“ add “(see 3.4.3).“. PAGE 25 Figure 1, title line, delete “type“ and substi
23、tute “Type“. PAGE 26 Figure 2, title line, delete “type“ and substitute “Type“. PAGE 27 Figure 3, title line, delete “type“ and substitute “Type“. Figure 4, title line, delete “type“ and substitute “Type“. PAGE 28 Figure 5, title line, delete “type“ and substitute “Type“. Provided by IHSNot for Resa
24、leNo reproduction or networking permitted without license from IHS-,-,-PAGE 29 Figure 6 Delete “TYPE I PROBES“ and substitute “TYPES Ia and Ih PROBES“. TYPE I ONLY L, E2 L, E2 9 UNITS -4OOF 10 UNITS +140F ? PAGE 30 Figure 7 Delete “TYPE I PROBES“ and substitute “TYPE Ia and Ib PROBES“. PAGE 31 Figur
25、e 8, in third box from bottom of the flow chart, delete “1“ and substitute “2“; and delete “,O“; in last box of flow chart, delete “1“ and substitute “2“; and delete “,O“. of the last box of the flow chart, add the following box: Figure 8, parallel and to the left Figure 8 Notes, add shown.“ 3/ Only
26、 operational tests shall be run at temperature - Figure 8 Legend, after “V“, add “E - Electrical Inspections Type I Probes - 4.7.3.1 Type II Probes - 4.7.3.2.1“ Figure 8 Legend, add “1“ after first “E“; after “Type II Probes - 4.7.3.2.1“ add “(S3 through S10 only)“; and delete “1“ after “El“ and add
27、 *2. Figure 8, in third and fifth box from top, add “1“ after “E“. PAGE 35 Substitute new Figure 13 b Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ANENDMENT 2- I PAGE 36 Figure 14, title line, delete “type“ and substitute “Type“. PAGE 37 Figure 15
28、, title line, delete “type“ and substitute “Type*. PAGE 38 Figure 16, Add NOTE above figure title: II NOTE: Negative spectrum to be with- in 90 percent of positive spectrum for each shock test performed.“ PAGE 39 Figure 17, Add “(5.8 grms)“ to the end of the figure title. PAGE 40 Figure 18, Add “(9.
29、2 grms)“ to the end of the figure title. PAGE 41 Delete paragraph number “3.1.3“ and substitute “3.8.1“. Delete paragraph number “3.1.1“ and substitute “3.7“. Delete paragraph number “3.1.2“ and substitute “3.8“. PAGE 43 Delete paragraph number “3.7“ and substitute “3.9“. Provided by IHSNot for Resa
30、leNo reproduction or networking permitted without license from IHS-,-,-PAGE 44 Under “TABLES“, delete “type“ and substitute “Type“ c6 places. Under “FIGURES“, delete “type“ and substitute “Type“ (7. places). List of figures, Add “(5.8 grmc)“ to the end of the Figure 17 title and add (9.2 grms)“ to t
31、he end of the Figure 18 title; The margins of this amendment are markcd-with an asterisk or vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. the Government assumes no liability whatsoever for any inaccuracies in these
32、notations. Bidders and contractors are cautioned to evaluate tire TeQui rements of this document based on the entire content irressectivc of the marginal notations and relationship to the last pr-vious amendment. This was done as a convenience only and Preparing Activity: (Project 1336-N553) NAVY -
33、AS + Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c J1 F2 E2 A2 Al c1 c2 - Wl . bl r1,55 I A2 - y- LOGIC MODULE PART OF FZU4S/B I FIGRE12. Logic module test circuit. Y O TP3 ATTACH TO 7 PROBE CASE- GROUND FQfBE 13. Interface module test circuit. 3
34、5 “Supersedes page 35 of MIL-P-85459(AS) of 3 2 December 1983“ a B2 D1 c1 El 12 2 Sl 2 :2 :1 I INTERFACE MODULE PART Of FZU46/8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-O32 RAD TYPICAL 4 PLACES 0.470 TYPICAL 4 PLACES- 0.10 RAD MAX TYPICAL 4 PLACES NOTE: Mmrkl: Silbiw 22-R-765, Ckrr lb, GM 40. Thickmr: Ofo.007. FIWRE 14. Probe amket. type I. 36 “Reprinted without change“ U.S. EMRHBSI PRiNlM WFICE: 1987 - 744WM391 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
