1、MIL-PRF-23199E (SH) 28 Februarv 1997 SUPERSEDING 18 November 1992 MIL-P-23199D (SH) PERFORMANCE SPECIFICATION PACKAGING AND PACKING REQUIREMENTS FOR SPECIAL PURPOSE MECHANICAL COMPONENTS AND REPAIR PARTS This specification is approved for use by the Naval Sea Systems Command (NAVSEA), Department of
2、the Navy. s a 1. SCOPE 1.1 ScoDe. This specification covers the requirements for packaging, packing, and marking of mechanical components to safeguard cleanliness, prevent damage and corrosion, and presetve identification during shipment and storage. 2. APPLICABLE DOCUMENTS 2.1 General. The document
3、s listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list,
4、document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documenfs. 2.2.1 SDecifications and standards. The following specifications and standards form a part of this specific
5、ation to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. Beneficial comments (recommendations, addition
6、s, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Sea Systems Command, SEA 03R42,2531 Jefferson Davis Highway, Arlington, VA 22242-5160 by using the Standardization Document Improvement Proposal (DD From 1426) appearing at th
7、e end of this document or by letter. AMSC N/A FSC PACK DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-23199E W 9999906 2117311 T50 MIL-PRF-23199E (SH) SPECIF
8、ICATIONS MILITARY MIL-P-24466 - Polyethylene Bags, Sheet, and Tubing, Green. FEDERAL L-P-378 - Plastic Sheet and Strip, Polyolefin: STANDARDS MILITARY MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-767 - Control of Hardware Cleanliness. MIL-STD-2041 - Control of Detrimental Materials. MANUA
9、L UFC-3 -Standardized Inspection of Shipment Railcars. (Documents are available from the contracting agency or from the Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191 11-5094.) 2.3 Other Government documents and Dublications. The following other Governmen
10、t documents and publications form a patt of this specification to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. PUBLICATIONS DEPARTMENT OF TRANSPORTATION (DOT) Code of Federal Regulations (CFR) Title 49 - Transportation Chapter III - Federal
11、 Highway Administration Patts 390-399 - Federal Motor Carrier Safety Regulations (Application for copies of the Code of Federal Regulations should be addressed to the Superintendent of Documents, Government Printing Office, Washington, DC 20402.) 2.4 Order of precedence. In the event of a conflict b
12、etween the text of this document and the references cited herein, the text of this document shall take precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exception has been obtained. 2 Provided by IHSNot for ResaleNo reproduction or networking
13、 permitted without license from IHS-,-,-MIL-PRF-23199E 9979906 2117312 977 MIL-PRF-23199E (SH) 3. REQUIREMENTS 3.1 Definltlons. (a) ComDonents. Any mechanical item, assembly, equipment, component, repair part, and tooling governed by this specification. (b) Controlled part specifications. Any refere
14、nce to (or application of) of one or more of the documents listed in MIL-STD-2041 Appendix D. (c) Critical surface. A surface which, when corroded or otherwise roughened, can impair the components proper function. Examples include small orifices, bearings, bellows, seating surfaces, seal weld diaphr
15、agm closure parts, thread surfaces, seal membranes or heat exchanger tubing up to 1/8 inch thick. handling and shipment from shock and vibration damage. The cushioning materials shall have sufficient strength to perform this function and resist puncture and tearing of envelopes. (e) Foreian material
16、. Any material or object that should not be on or within clean components. Examples include gr the identification label containing the bar code national stock number shall be permanently affixed to the outside of the envelope. Labels shall be fabricated to fit the envelope. If labels are supplied an
17、d which may exceed the envelope size, the label may be trimmed and/or folded over the envelope provided the label remains legible and bar codes are not folded. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MlL-PRF-23199E (SH) 3.6 Shipment. If the
18、 vehicle is not covered, the component shipment shall be covered with a water repellant tarpaulin. The supplier shall ensure that components which need to be secured to the transportation vehicle are adequately secured. Rail and barge shipments of components and shipments of hazardous materials are
19、permissible provided they are permitted by the procurement documents or approved by the contracting agency. 3.7 packaaina. packina and shtpplna pr ocedures. A procedure is required which describes the methods that will be used by the supplier to clean, preserve, package, pack, mark, and ship compone
20、nts and shall be made available for review upon request. Unless otherwise approved by the contracting agency, the procedure shall conform to the requirements of this specification. 4. QUALITY ASSURANCE PROVISIONS 4.1 ResDonsibilitv for insDection. Unless othetwise specified in the contract or purcha
21、se order, the supplier is responsible for the performance of inspection requirements as follows: 4.1 .I Inspection/visual tests. (a) All packaging, packing and marking shall be visually inspected to determine compliance with specification requirements. Wood boxes, including contents, exceeding 10,00
22、0 pounds shall be inspected to verify the integrity of the box. (b) The shipping vehicle shall be visually inspected when the shipment exceeds 1,000 pounds. Shipping vehicles with unsatisfactory conditions shall not be used. All truck shipments shall comply with DOT CFR Title 49, Chapter III, Parts
23、390-399 and have a driver vehicle inspection report in accordance with Part 396.1 1. The items to be checked on the loaded vehicle prior to release shall be identified in the suppliers packaging, packing, and shipping procedure when the shipment exceeds 1,000 pounds. As a minimum, the loaded truck s
24、hall be inspected for (1) load shored and tied down as needed, (2) weight properly distributed and not overloaded, and (3) tailgates and doors on enclosed components secured. Rail shipments shall be inspected in accordance with UFC-3. 5. PREPARATION FOR DELIVERY This section is not applicable to thi
25、s specification. 6. NOTES 6.1 Orderina datq. Procurement documents shall specify the following: (a) Title, number, and date of this specification. (b) Whether the quantity per unit package is other than one and whether packaging to be used is other than in accordance with paragraph 3.3 (see 3.3.1).
26、(c) Whether specialized preservation methods are required and, if so, the specific method (see 3.3.7). 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-23199E (SH) (d) Whether each package does not require a separate pack (see 3.4.1). (e) Wh
27、ether any specific design, construction and testing of the container are required (see 3.4.1). (9 Special marking requirements (see 3.5.1). 6.2 elationshiD to orevious revisions. 6.2.1 Packaaina and oackina levels. Previous revisions to this document referenced levels A, B, and C of packaging and pa
28、cking. This revision eliminated these level designations; thus, any contractual document referencing these levels are no longer applicable. The entire specification should be assumed applicable unless othewise noted in contractual documents. 6.2.2 Packaaina and ornina of electronic comoonents. Previ
29、ous revisions to this document contained packaging and packing requirements for electronic components which have been eliminated in this revision. Packaging and packing requirements for electronic components which includes instrumentation and control equipment are now contained in MIL-PRF-23199/1. 6
30、.3 Chanaes from previous issue. Margin bars are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Preparing activity: Navy - SH (Project PACK-N059) 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
