1、MIL-STD-1320 -235 1 W 7777711 0070871 3 3- 37-07 MILITARY STANDARD MIL-STQ-1320-235 TRUCKLOADIN6 ENCAPSULATED TOEM, TOTEM VEHICLE AND EXPENDED CAPSULE CNAW) 18 NOVEMBER 1988 EHCAP TOTEM DATA TOTEM CAPSULE VEHICLE OOOICIIIALC. LENGTH . 2q8.2 IN 248-2 III 243.3 III DIAMETER . 21 IN 21 Irr 20.4 III GRO
2、SS WEIGHT . 3,500 LBS 400 LES 2.600 LBS CUBE . 50 CU FT 50 CU FT 96 CU FT - AMCC NO. - N/A DISTRIBUTION STATEMENT A APPROVED FOR PUBLIC RELEASE: DISTRIBUTION IS UNLIMITED. NOTES: I. UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES. 2. FOR CROSS REFERENCE TO ASSOCIATED PALLETIZING, CONTAINERLOADIN
3、G ANO CARLOADING MILITARY STANDARDS, REFER TO INDEX TO STANDARDS, AUTHORIZED AND RELEASED FQR HIGHWAY SHIPMENT ONLY. - iWSTA EMLE RATE SIQNATUWE u BY DIRECTIH DATE * /I /Y-&$ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-STD-3320 -235 3 W 7797
4、733 0070872 5 W M Il-STD-1320-23 5 (NAVY) GENERAL NOTES 1. THIS DOCUMENT GIVES DETAILED INSTRUCTIONS FOR TRUCKLDADING THE TTL ENCAPSULATED TEST MISSILE. BARE TEST MISSILE OR EMPTY CAPSULE. FOR GENERAL TRUCKLOADIPG PROCEDURES, RFFFR TO MIL-STD-1320 i NAVY) . THE PROCEDURES DESCRIBED HEREIN ARE INTEHD
5、ED FOR 28 FT AND LONGER FLATBED TRAILERS. TRAILERS WITH METAL FLOORS. CHAINS AND STEEL STRAPPING MAY BE USED INTERCHANGEABLY ON A ONE-TO-ONE BASES FOR TIEDOWNS. STEEL STRAPPING USED AS TIEDOWN SHALL BE 2 X .O50 AND SHALL CONFORM TO AND BE APPLIED AS SPECIFIED IN THE GENERAL TRUCKLOADING DOCUMEtlT. M
6、IL -STO-l320 (NAVY 1. CHAIHS. FITTINGS AND LOAD BINDERS SHALL CONFORM TO AND BE APPLIED AS SPECIFIFD IN THE GENERAL TRUCKLOADING DOCUMENT. MIL-STD-1320 (WAVY). EXCEPT THAT THE CHAINIGRAB HOOKS SHALL BE ATTACHED TO THE STAKE POCKETS (NOT AROUHD THE RUB RAIL). PROTECTOR BOARDS SHALL BE USED UNDER THE
7、TIEDOWNS. BE STAPLED TO THE PROTECTOR BOARD USING 2 INCH STRAPPING STAPLES. SHALL BE SECURED TO THE PROTECTOR BOARD BY ERIVING A 1Od NAIL THROUGH THF CHAIN LINK AND CLINCHING THE NAIL OVER THE CHAIN. FIVE STAPLESINAILS SHALL BE USED FOR FACH TIEDOWN. PRIOR TO LOADING THE TRAILER AND DURING PRELOADIN
8、G INSPFCTION (REOUIRED BY NAVSEA OP 2165 AND REPORTED 011 DD FORM 626). THE CHAIHS. FITTINGS ANO LOAD BINDERS SHALL PE INSPECTED FOR STRETCH. GOUGIIJG. BCNT LINKS. WEAR AND ANY OTHER NOTICEABLE DEFECTS. THE INSPECTOR SHALL CONFIRM THAT THE CHAINS. FITTINGS AND LOAD BIHDERS HAVE BEEN INSPECTED AND SH
9、ALL SO NOTE IN ITEM ND. 22 OF DD FORM 626. 2. DO NOT USE 3. 4. 5. 6. WHEN USING STEEL STRAPPING, THE STRAPS SHALL WHEN USIIE CHAIN. THE CHAINS 7. ANY DEFICIENCY SHALL BE CAUSE FOR REJECTION OF A CHAIN OR LOAD BINDER. 8. UNLESS OTHERWISE SPECIFIED DUNNAGE LUMBER. STEEL STRAPPING. STRAP SEALS AND NAIL
10、S SHALL BE AS SPECIFIED Ill THE GENERAL TRUCKLOADING DOCUMEHT. MIL-STD-1320 (NAVY 1. 9. THE MAXIMUM GROSS WEIGHT OF THE TRACTOR-TRAILER AED THE ALLOMABLE AXLE WEIGHTS ARE THE RESPONSIBILITY OF THE CARRIER. SHIPPER SHALL LOA0 THE TRAILER IN SUCH A MANNER THAT THE TRACTOR-TRAILER WILL NOT EXCEED THESE
11、 LIMITATIONS. THE CARRIER WIL ADVISE THE SHIPPER OF THESE LIMITATIONS AND THE 10. AFTER THE BLOCKING. BRACING AND TIEDOWNS HAVE BEEN INSPECTED, THE ITEMS SHALL BE COMPLETELY COVERED WITH FIRE RESISTANT. WATERPROOF TARPAULINS. AFTER THE TARPAULINS ARE IN PLACE. ATTACH APPROPRIATE PLACARDS TO BOTH SID
12、ES, FRONT AND BACK OF THE TRAILER (WHEN APPLICABLE) AND ATTACH THE SHIPPING DOCUMENTS TO AH ACCESSIBLE AREA ON THF BACK DECK OF THE TRAILER. 11. FTL 28 tl AND LONGER TRAILER (FLATBED) 2 X 4 X 24 QUADRUPLED. AFTER ASSEMBLY OF CHOCKS, NAIL ITEM 3 TO TRAILER FLOOR WITH 6 - 16d NAILS. NAIL 2ND LAYER TO
13、1ST IN LIKE MANNER AND CONTINUE FOR 4 LAYERS. 2 X 6 X 24 QUINTUPLED. NAIL ITEM 1 TO TRAILER FLOOR WITH 3 - 16d NAILS. HAIL 2ND LAYER TO 1ST IN LIKE MANNER ANO CONTINUE FOR 5 LAYERS. DETAIL 7 % 24 36 2 X 6 X 72 QUIIITUPLEO. TO TRAILER FLOOR WITH 1 - 160 NAIL NAIL ITEM 2 EVERY 8 INCHES. TO FIRST IN LI
14、KE MANWER AND CONTIHUE FOR 5 LAYCRS. NAIL SECONO LAYER PREPOSITIONED FLOOR BLOCKING FOR 28 FT OR LOHGER TRAILER PAGE 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1320 -235 81 7777711 0070873 7 FULL TRUCKLOAD MIL-STD-1320-235 (NAVY) XPSUL
15、E (REF), SEPARATOR, PROTECTOR ASSEMBLY # I I # REF NOTE TARPAULINS OtlITTED FOR CLARITY. NOTE DIRECTION OF ARROW INDICATES FORUARD END OF TOTEM. SECTION 6-6 KICKER ASSEMBLY PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1320 -235 1 77
16、777L1 0070874 7 H MIL-STD-1320-235 (NAVY) LESS THAN TRUCKLOAD 2 X 8 X 2i QUINTUPLED. WAIL ITEM 10 TO TRAILER FLOOR WITH i - 16d NAILS. NAIL 2ND LAYER TO IST IN LIKE AND CONTINUE FOR 5 LAYERS. 2 X Li X 24 QUADRUPLES. OTHER. SAME AS 3 - 81 26 b- 162 215 MANNER NAIL CROSSMEHBER. ITEM 20. TO BACKUP CLEA
17、T. ITEM 1D. VERTICALLY AS SHOW WITH 3 - 16d NAILS. ENSURE NAIL HEADS ARE BELOW THE WOOD SURFACE. NOTE TARPAULINS OMITTED FOR CLARITY- NOTE DIRECTION OF ARROW IIIDICATES FORWARD END OF TOTEH. 4 NOTE THE O IN THE ITEM NUMBER REPRESENTS SHORTCR VERSIONS OF THE ITEMS CALLED OUT ON FTL. h SECTION DD W ?A
18、G A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I- a I MIL-STD-1320 -235 81 m 7477711 O070875 0 = - I M IL-STD-13 20-2 3 5 (NAVY) CHOCK ASSEMBLY INSTRUCTION i. ASSEMBLE TIIE CHOCKS OE1 THF TRUCKS FOLLOWIEIE THESE ItlSTRUCTIOtIS. FOR LESS THAI TRU
19、CK (LTL) LOAD USE THE LTL LIST OF MATERIALS ANO SFCTIOII 0-0. 2. BEFORE STARTIWG. BEVEL ITEMS 6 AH0 7 AND FOR FULL TRUCK LOADS (FTLI ONLY1 AND ITEMS 17 AND 18 AS SHOWN II1 SECTION 8-6 OR SECTION 0-0 1-112 INCHES BY 45 DEGRFES. 3. NAIL CHOCK EASE. ITEM q. ON THE TRAILER FLOOR IN THE LOCATION INDICATE
20、D BY DETAIL A OR DETAIL E WITH i-16d NAIL EVERY 8 INCHES. REPEAT FOR ALL CHOCK LOCATIONS. q. NAIL LOWER CHOCK. ITEM 5. ON THE CHOGX BASE WITH 3 - i6d NAILS IN THE LOCATION INDICATED nr SECTION E-B OR SECTION 0-D. UPPER CHOCK, ITEM 7. TO TIIE MIDDLE CHOCK IN THE SAME IIANNER. HEXT HAIL THE MIDDLE CHO
21、CK, ITEM 6. TO THE LMR CHCK. ANO THE REPEAT FOR EACH CHOCK LOCATION. 5. FOR FTL. NAIL THE LOIER SPACER. ITEM 16. TO THE CHOCK BASE WITH 3 - 166 NAILS TM THE LDCATION SHOWN IN SECTION B-B. NAIL THE MIOOLE SPACER. ITEM 17. TO THE LOWFR SPACFR AND THE UPPER SPACER. ITEM 18. TO THE MIDDLE SPACER IN LIKE
22、 MANNER- REPEAT FOR EACH CHOCK LOCATION. KICKER ASSEMBLY INSTRUCTION i. PRIOR TO ASSEMBLY. BEVEL q EDGES OF KICKER BOARD. ITEM 13. 31q BY 45 DEGREES AS SHOWN IN DETAIL C. 2. NAIL TOP SUPPORT, ITEM 12. TO THE END OF THE VERTICAL SUPPORT. ITEM 11. WITH fi - 8d NAILS. ENSURE HO NAILS PROTRIIDE PAST THE
23、 FACE OF THE VERTICAL SIIPPORT. NAIL THE VERTICAL SUPPORT, ITEM li. TO THE END OF THE BOTTOM CLEAT, ITEM 10, WITH 3 - 16d NAILS. PLACE THE KICKER BOARD, ITEM 13. AGAINST THE VERTICAL SUPPORT, TOP SUPPORT. AND ROTTOM CLEAT IN THE LOCATION SHOWN OW DETAIL C AT A 45 DEGREE ANGLE. 3. q. NAIL KICKER BOAR
24、D TO THE BOTTOM CLEAT. ITEM 10. WITH 2 - 16d NAILS. AFTER PLACING THE TTL TOTEMS IN THE CHOCK WITH THE AFT END BUTTED AGAINST THE CROSSMFMBER. 5. ITEM 2. PLACE THE KICKER ASSEMBLY AGAINST THE FORWARD tim MITH THE VERTICAL SUPPORT, ITEH II. BUTTE0 AGAINST THE FORWARD END. WITH 6 - 16d NAILS, CLEAT AN
25、D HAIL IN LIKE MANNER. REPEAT PROCEDURE FOR FTL. HAIL THE ASSEMBLY TO THE TRAILER FLOOR THROUGH THE BOTTOM CLEAT BUTT THE TOP CLEAT. ITEM 19. AGAIIIST THE KICKER BOARD ABOVE THE BOTTOM PROTECTOR BOARD ASSEMBLY INSTRUCTION i. 2. NAIL PROTECTOR BOARDS. ITEM 8. TOGETHER WITH B - 86 NAILS. NAIL KEEPER B
26、OARD. ITEW 9. TO THE PROTECTOR BOARDS WITH 3 - 16d NAILS IN THE LOCATIDM SHOWI IN SECTION B-B (OR SECTION D-D) FOR LTLI. MANNER. NAIL A SECOND KEEPER BOARD TO THE FIRST IN A LIKE 3- FOR FTL. NAIL SEPARATOR. ITEM 19. TO THE PROTECTOR BOARD AT THE LOCATION SHOWN IN SECTION E-8 WITH 3 - 6L NAILS. SECOH
27、O SEPARATOR BOARD TO FIRST IN LIKE MANNER. NAIL l. REPEAT PROCEDURES FOR EACH PROTECTOR BOARD . ASSEMBLY REQUIRED. FOR SINGLE LOAD, NAIL VERTICAL RETAINERS. ITEM 16D. FLUSH WITH THE UPPER PROTECTOR BOARD. ITEM 8. IN THE LOCATION SHOWN IN DETAIL F WITH 4 - 10c NAILS FOR EACH SUPPORT. PLACE PROTECTOR
28、BOARD ASSEMBtY OVER THE CAPSULE AS SHOLJN IN SECTION 0-0. INSTALL AND TENSION CHAIN AND LOA0 BINDERS. ITEM 15. OVER THE PROTECTOR BOARDS PER NOTE 5. NAIL VERTICAL RETAINERS TO THE CHOCK ASSEMBLY WITH 4 - 1Od NAILS FOR EACH SUPPORT. 5. NOTE VERTICAL RETAINER SHOULD NOT REST ON THE TRAILER FLOOR. *US. GOVERNMENT PRINTING OFFICE 1989: - 60&033/13249 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
