1、IL-STD-1322 -LOB = 9999933 0434229 675 REV TOA SYSCOM L TR REVISION DESCRIPTION DATE APPROVAL e e O STANDARDS. REFER TO INDEX TO STANDAROS. MIL-HDEK-236 (NAVYI. MIL-STD-1322-108 (NAVY1 MILITARY STANDARD UNIT LOAD FOR DOMESTIC AND OVERSEAS SHIPMENT 8 JULY 1992 TASK “A“ ASSY TEST CHARGES ON WOODEN SKI
2、D WITH COVER & END FRAME ASSYS MIS UNIT LOAD IS AUTHORIZED AND RELEASED FOR DEPOT HANDLING AND STORAGE AND FOR SHIPMENT BY COMMON CARRIER. 7- 7-92 7- 6-52. DATE WPNSTA EARLE DATE &A-. (8 OR 16-PACK UNIT LOADS) UNIT LOAD DATA GROSS WEIGHT OF (E) UNITIZED TEST CHARGES - - - - - - 544 LBS. GROSS WEIGHT
3、 OF WOOD SKID & PARTS -PACK) - - - - - 170 LES. (APPROX) GROSS WEIGHT OF WOOD SKID & PARTS (16-PACK) - - - - - 183 LBS. (APPROXI GROSS WEIGHT OF UNIT LOAD -PACK) - - - - - - - _ 714 LES A GROSS WEIGHT OF UNIT LOAD (1SPACK) - - - - _ - - - 1,271 LES. a CUBE (&PACK) - - - - - - - - - - - - - - - - - -
4、 - 26.89 CU/Fi. CUBE (WPACK) - - - - - - - - - - - - - - - - - _ - 40.18 CU/FT. , - -,., ,.- - .II. .-. _ REQUIREMENTS FOR CONSTRUCTION OF THIS UNIT LOAD SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF MIL-STD-1322 NAVY). - I* dh /J . DATE ORIGINATOR WPNSTA EARLE. NEW JERSEY L VU NUI J5t run
5、anii “Nb WtlbI FOR HAZARD CLASSIFICATION SEE NAVSEA OP2165 II ) UNITIZED TEST CHARGES AMSC NO. - NIA DISTRIBUTION STATEMENT A APPROVE0 FOR PUBLIC RELEASE: w (a) UNITIZED TEST CHARGES Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1322 -108 m
6、 9999911 0434230 397 m FOR PICTORAL AND UNITIZING PROCEDURES SEE PAGES 3 & 4. BASE (SEE DETAIL C) VERTICAL SEE DETAIL SUPPORT H /. END FRAME ASSY (2 REQD) (SEE DETAIL F) 8-PACK UNIT LOAD Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1322 -1
7、08 W 9999933 0434233 223 a MIL-STD-1322-108 PICTORIAL SEQUENCE FOR 16-PACK UNIT LOAD NOTE : FOR UNITIZING ONE %PACK, REPEAT PICTORIAL SEOUENCE AS SHOWN, EXCEPT OMIT ONE UNITIZED 8-PACK LOAD AND USE THE SMALLER END FRAME ASSY (DETAIL F) IN LIEU OF THE LARGER END FRAME ASSY (DETAIL GL FOR STRAPPING PR
8、OCEDURES SEE PAGE 4 - 0 FOR 8-PACK !F DETAIL G (NAVY 1 PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1322 -LOB m 9999911 0434232 1bT m UNITIZING PROCEDURE (TWO &PACKS) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. USING LIFTING TOOLASSEMBLY #O1 121
9、00A, CAREFULLY STACKONEI-PACK OF CANISTERS ON BASE ASSEMBLY. LIFTING FEATURES ON 8-PACK SHOULD BE ALIGNED WITH SLOTS ON BASE AS SHOWN. USING THE SAME LIFTING ASSEMBLY, CAREFULLY STACK A SECOND 8-PACK OF CANISTERS ON TOP OF THE FIRST ONE. BE SURE TO ALIGN THE LIFiING/STACKiNG FEATURES. POSITION TWO L
10、ARGE END FRAMES (DETAIL G) INTO SLOTS WITH FOAM FACING TOWARD THE CANISTERS. PLACE TWO LATERAL STRAPS, ITEM 28, THROUGH SLOTS, UNDER BASE ASSEMBLY, AND OVER STACKING FEATURES OF CANISTERS AS SHOWN. TENSION AND SECURE EACH STRAP WITH ONE DOUBLE NOTCHED SEAL, ITEM 34. POSITION COVER ASSEMBLY (DETAIL A
11、) OVER CANISTERS, ALIGNING SLOTS ON COVER WITH THE END FRAMES AS SHOWN. POSITION VERTICALSUPPORT, ITEM 38, IN LINE WITH BASESKIDS AND SNUG UNDER COVER. SCREW SUPPORT INTO BASE AND COVER WITH (1) DRYWALL SCREW, ITEM 40,4PL IN BASE AND 4PL IN COVER AS SHOW IN DETAIL H. POSITION STRAPS, ITEM 29, OVER S
12、TACKING FEATURES, ITEM 7, OF COVER ASSEMBLY AND UNDER BASE ASSEMBLY AS SHOWN. TENSION AND SECURE EACH STRAP WITH ONE DOUBLE NOTCHED SEAL, ITEM 34. PLACE TWO LONGITUDINAL STRAPS, ITEM 30, THROUGH SLOTS ON END FRAMES AND AROUND LOAD AS SHOWN. TENSION AND SECURE EACH STRAP WITH ONE DOUBLE NOTCHED SEAL,
13、 ITEM 34. CONSTRUCTION OF END FRAMES, BASE, AND COVER ASSEMBLIES IS SHOWN ON PAGES 5 THRU 7 SECURE STRAPPING, ITEM 29, TO STACKING FEATURE WITH ONE STAPLE, ITEM 35, ON EACH END. UNITIZING PROCEDURE (ONE &PACK) 1. 2. 3. 4. 5. 6. 7. 8. 9. USING LIFTING TOOL ASSEMBLY #O1 12100A, CAREFULLY STACKONE 8-PA
14、CK OF CANISTERS ON BASE ASSEMBLY. LIFTING FEATURES ON 8-PACK SHOULD BE ALIGNED WITH SLOTS ON BASE AS SHOWN. POSITION TWO SMALL END FRAMES (DETAIL F) INTO SLOTS WITH FOAM FACING TOWARD THE CANISTERS. PLACE TWO LATERAL STRAPS, ITEM 31, THROUGH SLOTS, UNDER BASE ASSEMBLY, AND OVER STACKING FEATURES OF
15、CANISTERS AS SHOWN. TENSION AND SECURE EACH STRAP WITH ONE DOUBLE NOTCHED SEAL, ITEM 34. POSITION COVER ASSEMBLY (DETAIL A) OVER CANISTERS, ALIGNING SLOTS ON COVER WITH THE END FRAMES AS SHOWN. POSITION VERTICALSUPPORT, ITEM 37, IN UNE WITH BASE SKIDSAND SNUG UNDER COVER. SCREW SUPPORT INTO BASE AND
16、 COVER WITH (1) DRYWALL SCREW, ITEM 4,4PL IN BASE AND 4PL IN COVER AS SHOWN IN DETAIL H. POSITION STRAPS, ITEM 32, OVER STACKING FEATURES, ITEM 7, OF COVER ASSEMBLY AND UNDER BASE ASSEMBLY AS SHOWN. TENSION AND SECURE EACH STRAP WITH ONE DOUBLE NOTCHED SEAL, ITEM 34. PLACE ONE LONGITUDINAL STRAP, IT
17、EM 33, THROUGH SLOTS ON END FRAMES AND AROUND LOAD AS SHOWN. TENSION AND SECURE EACH STRAP WITH ONE DOUBLE NOTCHED SEAL, ITEM 34. CONSTRUCTION OF END FRAMES, BASE, AND COVER ASSEMBLIES IS SHOWN ON PAGES 5 THRU 7 SECURE STRAPPING, ITEM 32, TO STACKING FEATURES WITH ONE STAPLE, ITEM 35, ON EACH END. c
18、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1322 -LOB 9999911 0434233 OTb a a O MIL-STD-1322-108 (NAVY) SUGGESTED NAILING PROCEDURE (COVER) : 1. 2. 3. 4. 5. 6. 7. 8. NAIL STACKING FEATURE, ITEM 7, TO SPACER BOARDS, ITEM 5, AS SHOWN IN VI
19、EW B. USE 466 NAILS PER JOINT. PLACE TWO DECK BOARDS, ITEM 2, ON TOP OF ITEM 7 AND SNUG AGAINST KEM 5. BE SURE TO MAINTAIN THE 9 5/8 OVERHANG INDICATED IN VIEW B. NAIL DECK BOARDS TO SPACERS, ITEM 5, W/2-10d NAILS PER JOINT. PLACE DECK BOARDS, ITEM 4, ON TOP OF TTEM 7 AND FLUSH AGAINST ITEM 5. NAIL
20、DECK BOARDS TO KEM 5 WjP-lOd NAILS PER JOINT. PLACE SPACER BOARDS, ITEM 3, ON TOP OF TTEM 7 AND FLUSH AGAINST ITEM 4. NAIL SPACER BOARDS. ITEM 3. TO ITEM 4 W/34d NAILS PER JOINT. PLACE TWO DECK BOARDS, ITEM 2, ON TOP OF TTEM 7 AND SNUG AGAINST ITEM 3. BE SURE TO MAINTAIN THE 9 5/8 OVERHANG AS REQUIR
21、ED IN STEP 2. NAIL DECK BOARDS TO ITEM 3 W/Z-lOd NAILS PER JOINT. NAIL DECK BOARD, ITEM 1, TO ITEM 2 W/l-lOd NAIL EVERY 8 INCHES. SECURE END BOARDS, ITEM 6, TO ENDS OF DECK BOARDS, KEM 2, WITH TWO LAG BOLTS, ITEM 9, PER JOINT. USE ONE WASHER, ITEM 10, PER BOLT. CENTRALLY LOCATE BOLTS INTO ENDS OF DE
22、CK BOARDS, ITEM 2. TURN EASE ASSEMBLY OVER AND NAIL DECK PLATE, ITEM , TO ITEMS 1,2, AND 6. USE 10d NAILS. 3 51s 4 PL CWER (INVERTEDFORASSEMBLY) I 1 (3 518) I d VIEW B ZPL OUTER DECKING REMOMD FOR CuRm PAGE 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I
23、HS-,-,-MIL-STD-1322 -108 9LL 0434234 T32 MIL-STD-1322-108 (NAVY) SUGGESTED NAILING PROCEDURE (BASE) : 1. 2. 3. 4. 5. 6. 7. 8. NAIL BO?TOM SPACERS, ITEM 15, TO BASE SKID, ITEM 17, AS SHOWN IN VIEW D W/ClOd NAILS PER SPACER. NAIL TOP SPACERS, ITEM 15, TO BOlTOM SPACERS IN LIKE MANNER. PLACE TWO DECK B
24、OARDS, ITEM 14, ON TOP OF BASE SKID, ITEM 17, AND SNUG AGAINST SPACERS, ITEM 15, AS SHOWN IN VIEW D. BE SURE TO MAINTAIN THE13 1/40VERHANG INDICATED IN VIEW D. NAIL DECK BOARDS TO SPACERS W/2-10d NAILS PER JOINT. PLACE DECK BOARDS, ITEM 13, ON TOP OF ITEM 17 AND SNUG AGAINST SPACERS, ITEM 15, AS SHO
25、WN. NAIL DECK BOARDS TO SPACERS W/2-10d NAILS PER JOINT. PLACE SPACER BOARDS, ITEM 12, ON TOP OF ITEM 17 AND NAILTO DECK BOARD, ITEM 13, W/3-1Od NAILS EACH. NAIL DECK BOARDS, ITEM 14, TO SPACERS, ITEM 12, W/2-10d NAILS PER JOINT. BE SURE TO MAINTAIN THE 13 1/4 OVERHANG AS REQUIRED IN STEP 2. NAIL DE
26、CK BOARDS, ITEM 11, TO ITEM 14 W/1-lOd NAIL EVERY 8 INCHES. SECURE END BOARDS, ITEM 16, TO ENDS OF DECK BOARDS, ITEM 14, WITH TWO LAG BOLTS, ITEM 9, PER JOINT. USE ONE WASHER, ITEM 10, PER BOLT. CENTRALLY LOCATE BOLTS INTO DECK BOARDS. TURN BASE ASSEMBLY OVER AND NAIL DECK PLATE, ITEM 18, TO ITEMS 1
27、1, 14, AND 16. USE 10d NAILS. PAGE 6 DETAIL E 6pL Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-L322 -108 11 0434235 979 MIL-STD- 1322- 108 (NAVY) NAILING & ASSY PROCEDURES 1. NAIL SIDE BRACE, TTEM 19, TO END CLEAT, ITEM 20 , W/46d NAILS AS
28、 SHOWN IN DETAIL F. 2 PL 2. NAIL (1) PLYWOOD CUSHION BASE, ITEM 21, TO SIDE BRACES, ITEM 19, W/4-6d NAILS/SIDE. 3. ADHERE CUSHION, ITEM 22, TO PLYWOOD BASE, ITEM 21, WITH ADHESIVE, TTEM 23. W 2 PL I r NAILING & ASSY PROCEDURES END FRAME ASSY (2) REQD 1. NAIL SIDE BRACE, ITEM 25, TO END CLEAT, ITEM 2
29、4, W/5-6d NAILS AS SHOWN IN DETAIL G. 2 PL. NAIL (1) PLYWOOD CUSHION BASE, ITEM 26, TO SIDE BRACES, ITEM 25, W/46d NAILS/SIDE. ADHERE CUSHION, ITEM 27, TO PLYWOOD BASE, ITEM 26, WITH ADHESIVE, ITEM 23. 2. 3. DETAIL G PAGE 7 END FRAME ASSY (2) REQD Provided by IHSNot for ResaleNo reproduction or netw
30、orking permitted without license from IHS-,-,-4 41 NAIL, DRYWALL STEEL 4 40 SCREW, DRYWALL 4 39 STRAP, JOINER (8-PACK) (16-PACK) 4 3 SUPPORT, VERTICAL (16-PACK) WOOD POR 4 37 SUPPORT, VERTICAL -PACK) AR 38 INK, STENCIL A-A-XK) 1 LG.* 1- 1 1/4“ LG. .O35 X 314 X 3 1 X 4 X (23p 1 X4X(11 1/2)* FITUNDERC
31、OVER STAPLES STEEL 35 314 SIZE AR 34 STRAP SEAL STEEL 314SlZE 133 LONGTUDINAL STRAP, 6-PACK STEEL 314 X ,035 X 18 112 Ff COVER STRAP, &PACK STEEL 314 x .O35 x9 FT 1 PPP-C-1752 21b 22 13/16 X 23 518 X 2 27 CUSHION (DETAIL G) 2 24 END CLEAT (DETAIL G) WOOD 2X4X 295116 AR123 I ADHESIVE (DETAIL F 8. G)
32、MMM-A-121 122 CUSHION (DETAIL F) 1 21 BASE, CUSHION (DETAIL F) 220 END CLEAT (DETAIL Fl PPP-C-1752 21b PLYWOOD 11 318 X 23 518 X 2 112 X 11 310 X 23 518 WOOD 2x4 17718 2 3 2 18 DECK PLATE (DETAIL C) WOOD 1 X 6 X 26 112 4 X 4 X 26 112 17 BASE SKID (DETAIL C) WOOD 16 END CLEAT (DETAIL CI WOOD 2 X 4 X
33、26 1/2 2 11 I DECKING, OUTER (DETAILC) I WOOD I 2 X4X66 114 28 DECK PLATE (DETAIL A) WOOD 1 XX26 112 b. REMOVE VERTICAL SUPPORT BOARDS BY UNSCREWING AND 27 STACKING FEATRE (DETAIL A) WOOD 1 X 4 X 26 112 2 6 END CLEAT (DETAIL A) WOOD 2 X 4 X 26 112 RE-AlTACHING TO OUTER EASE OR COVER AS SHOWN IN DETA
34、IL J. 2 X 4 X3 5/0 2 X 4 X 54 114 45 INNER SPACER (DETAIL A) WOOD 24 DECKING, INNER (DETAIL A) WOOD 43 OUTER SPACER (DETAIL A) WOOD 2 x 4 x 3 112 42 1 DECKING. INNER (DETAIL A) I WOOD I2X4X731/2 MIL-STD-1322 -108 m 9979911 OY3Y23b 805 m YI L-STD- 1322 - 108 (NAVY 1 NOTES: 1. ALL MATERIALS TO BE IN A
35、CCORDANCE WITH MIL-STD-1322 (NAVY) 2. DO NOT USE TYPE I STRAPPING WITH POWER MACHINES. P I 2 I 31 I CANISTERSTRAP.8-PACK I STEEL I 3/4X.O35X6Ff kAlL, ITEM 41, NOT TO PROTRUDE BEYOND BOARD. CUT OFF OR 30 I LOYGTTVDINAL STRAP, 16PACK I STEEL I 3/4 X ,035 X 18 112 FT t BEND OVER. DETAIL H VERTICAL SUPP
36、ORT (FOR BOTH 8 & 16-PACK UNIT LOADS) 4 PL I 2 I 29 I COVERSTRAP. 16-PACK I STEEL 1 3/4X.O35X11 FI 228 I CANISTER STRAP, 16-PACK I STEEL I 314 X .W5 X 9 1/2 Ff a I 2 I 19 I SIDEBRACE(DETA1LF) I WOOD I 2X4X 11 3/8 AFTER REMOVING COVER, RE-AlTACH VERTICAL SUPPORT BOARD ITEMS, 37 OR 38 TO BASE OR COVER
37、 FOR RE-USE. I 12 I 15 I INNERSPACER(DETAILC1 I WOOD I 2X4X3518 I 4 I 14 I DECKING, INNER (DETAIL C) I WOOD I 2 X4X73 1.12 I 2 I 13 I DECKING, INNER(DETAILC) I WOOD I 2X4X47 DETAIL d STORAGE POSITION OF VERTICAL SUPWRT I 6 I 12 I OUTERSPACERIDETAILC) I WOOD I 2X4X31/2 I 16 1 i0 I FLAT WASHER (DETAIL
38、A 8. Cl I MS9320-12 I 3/40.D.X .401 1.0. I 16 I 9 I LAG BOLT (DETAIL A & C) I MS16922-5456 I 3/8 DIA x 3 LONG DE-UNITIZING PROCEDURE a. CUT AND REMOVE LATERAL AND LONGITUDINAL STRAPPING c. REMOVE COVER. d. REMOVE END FRAMES ON EACH END. e. REMOVE TEST CHARGE CANISTERS. REQ-IITEMI DESCRIPTION 1 MATL/DWG I DIMENSIONS THIS DE UNITIZING PROCEDURE IS FOR BOTH 8 8.16-PACK UNIT LOADS. PARTS LIST PREPARING ACTIVITY: NAVY-OS (PROJECT NO. 814D-NI019) PAGE 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
