NAVY MIL-T-16618 A (2)-1963 TRUCK LIFT FORK DIESEL POWERED NAVAL SHIPBOARD《海军船柴油机发动叉斗起重机货车》.pdf

上传人:赵齐羽 文档编号:982511 上传时间:2019-03-12 格式:PDF 页数:1 大小:63.55KB
下载 相关 举报
NAVY MIL-T-16618 A (2)-1963 TRUCK LIFT FORK DIESEL POWERED NAVAL SHIPBOARD《海军船柴油机发动叉斗起重机货车》.pdf_第1页
第1页 / 共1页
亲,该文档总共1页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 I. - MIL-T-LhbLA (2) 37 W 4749906 0283732 O M /- I MILITARY SPECIFICATION MIL-T-l6618A(SHIPS) AMENDMENT - 2 12 June 1963 SUPERSEDING Amendment - 1 14 November 1958 TRUCK, LIFT, FORK, DIESEL POWERED, NAVAL SHIPBOARD This amendment forms a part of Military Specifi- cation MIL-T-l6618A(SHIPS), 2 Apri

2、l 1956. Page 2, paragraph 3.2 (o): Delete “5 degrees fore and 15 degrees aftt1 and substitute “5 degrees fore 11/2 degree and 10 degrees or more aft.“ Page 3, paragraph 3.10: Delete and substitute: 113.10 Brakes.- Foot operated service brakes and hand operated parking brake shall. be provided. Capac

3、ity of brakes shall be sufficient to stop the loaded truck in a distance of 10 feet or less when travelling forward or reverse, at rated load high speed down a 15 percent incline.11 Page 3, paragraph 3.11: Delete and substitute: “3.11 Transmission.- Transmission shall provide two forward and two rev

4、erse speeds through suitable reduction gears. The truck when carrying a rated load, shall have a high speed of 7 MPH and a low speed of 3 1/2 MPH, when driven forward or reverse. The truck, with a rated load shall ascend, in forward or reverse, a grade of. 10 percent at no specific speed.“ Page 5: A

5、dd new paragraph: l4.3 Responsibility for inspection. - Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection re- quirements as specified herein. Except as otherwise specified, the supplier may utilize his own facilities or an

6、y commercial laboratory acceptable to the Government. The Government reserves the right to perform any of the inspections set forth in the specifi- cation where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements.11 Preparing activity: .Navy - Ships (Project 3930-N003Sh) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • ASTM D2556-1993a(2005) Standard Test Method for Apparent Viscosity of Adhesives Having Shear-Rate-Dependent Flow Properties《具有切变速率决定其流速性能的胶粘剂的表观粘度的标准试验方法》.pdf ASTM D2556-1993a(2005) Standard Test Method for Apparent Viscosity of Adhesives Having Shear-Rate-Dependent Flow Properties《具有切变速率决定其流速性能的胶粘剂的表观粘度的标准试验方法》.pdf
  • ASTM D2556-2011 Standard Test Method for Apparent Viscosity of Adhesives Having Shear-Rate-Dependent Flow Properties 《用切变速率决定其流动性能的胶粘剂的表观粘度的标准试验方法》.pdf ASTM D2556-2011 Standard Test Method for Apparent Viscosity of Adhesives Having Shear-Rate-Dependent Flow Properties 《用切变速率决定其流动性能的胶粘剂的表观粘度的标准试验方法》.pdf
  • ASTM D2556-2014 Standard Test Method for Apparent Viscosity of Adhesives Having Shear-Rate-Dependent Flow Properties Using Rotational Viscometry《用切变速率决定其流动性能的胶粘剂的表观粘度的标准试验方法》.pdf ASTM D2556-2014 Standard Test Method for Apparent Viscosity of Adhesives Having Shear-Rate-Dependent Flow Properties Using Rotational Viscometry《用切变速率决定其流动性能的胶粘剂的表观粘度的标准试验方法》.pdf
  • ASTM D2557-1998(2004) Standard Test Method for Tensile-Shear Strength of Adhesives in the Subzero Temperature Range from -267 8 to -55&176C (-450 to -67&176F)《温度为-267 8至-55℃(-450至-.pdf ASTM D2557-1998(2004) Standard Test Method for Tensile-Shear Strength of Adhesives in the Subzero Temperature Range from -267 8 to -55&176C (-450 to -67&176F)《温度为-267 8至-55℃(-450至-.pdf
  • ASTM D2557-1998(2010)e1 Standard Test Method for Tensile-Shear Strength of Adhesives in the Subzero Temperature Range from -267 8 to -55&176C (-450 to -67&176F)《温度为-267 8至-55176C(-.pdf ASTM D2557-1998(2010)e1 Standard Test Method for Tensile-Shear Strength of Adhesives in the Subzero Temperature Range from -267 8 to -55&176C (-450 to -67&176F)《温度为-267 8至-55176C(-.pdf
  • ASTM D2559-2004 Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions《室外潮湿环境中层压结构木制品用胶粘剂的标准规范》.pdf ASTM D2559-2004 Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions《室外潮湿环境中层压结构木制品用胶粘剂的标准规范》.pdf
  • ASTM D2559-2009 Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions.pdf ASTM D2559-2009 Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions.pdf
  • ASTM D2559-2010 Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions《室外潮湿条件下用结构层压木材制品用胶粘剂标准规范》.pdf ASTM D2559-2010 Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions《室外潮湿条件下用结构层压木材制品用胶粘剂标准规范》.pdf
  • ASTM D2559-2010a Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions《室外潮湿环境中层压结构木制品用胶粘剂的标准规范》.pdf ASTM D2559-2010a Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions《室外潮湿环境中层压结构木制品用胶粘剂的标准规范》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1