1、er 4 a: LSEE VIEWS A,B,C, OR D, FOR APPLICABLE DETAILS. .200 MIN DEPTH I FED. SUP CLASS I 5935 +.21+ I 1.105 FULL THD .110f.015 L,625 4!* I.020 VIEW A: WITH GUIDEPINS VIEW E: WITH FIXED JACKSCREWS DENOTES CHANGE .A av - EC hhercust . RACK AND PANEL 4 SIZE 22 SOLDER PIN tF - 85 CONTACTS bimotfmOt TIT
2、LE MILITARY STANDARD CONNECTOR. RECTANGULAR, ELECTRICAL it“l MS14012 ,W - CR rocwemmt Spwillsatlon SUPERSEDES: IIL-C-28748 PAGE 1 OF 3 Licensed by Information Handling Servicesa .A Navy - EC thw curt LrnW - CR F - 85 a-o k-h*i TITLE MILITARY STANDARD CONNECTOR, RECTANGULAR, ELECTRICAL RACK AND PANEL
3、 4 CONTACTS *i(+ SIZE 22 SOLDER PIN MS14012 W 4 Y 4 Y rn 9 I4 t a 8 b 4 u I FED.WPCLASS I 5935 c 7 3PTIONAL CLAMP CONFIGURATION VIEW C: WITH SHORT TURNABLE JACKSCREWS CABLE OPENING .I87 MIN FULL THO .I IOf -015 2 PLACES I ,VIEW D: WITH LONG TURNABLE JACKSCREWS AND SHIELD I I Licensed by Information
4、Handling ServicesNSLLiOLZ REV C 59 9999912 00004b 3 w FED. SUP CLASS I 5935 INCHES I44 !INCHES M4 INCHES W4 .O02 .O5 .lo5 2.67 .250 6.35 .O03 .O8 .lo9 2.77 .270 6.86 .O04 .10 .110 2.79 .350 8.89 .O05 .13 .125 3.18 .500 12.70 .o08 .20 .145 3.68 .562 14.27 .O10 .25 ,146 3.71 ,600 15.24 .O15 .38 .I50 3
5、81 .620 15.75 ,020 .51 .187 4.75 .625 15.88 .O27 .69 .200 5.08 .760 19.30 .O45 1.14 .21 5.3 ,920 23.37 .O78 1.98 11 .210 5.33 II .960 24.38 .O90 2.29 .244 6.20 DESIGN STANDARD FOR USE WITH MIL-C-28748/7. NOTES 1. 2. 3. 4. 5. 6. 7. 8. 9. - 10. Dimensions are in inches. Metric equivalents are given f
6、or gen 1.00 inch 25.4 mn. ral information only and are based upon Dimensions and configuration shall be in accordance with the above figure. Unless otherwise specified, tolerances are t.02 (.5 mn) for two place decimals and 1.015 (.38 mn) for three place decimals. Tolerance between any two adjacent
7、contact centers shall be t.004 (.lo mn). Tolerance between any two contact centers, other than adjacent contacts, shall be 1.006 (.15 mn). Contact letter identification may be located on either side of the contact hole All letters shall appear on the front and rear face of each insert. Insetts shall
8、 be used with guide pin assemblies or jackscrew assemblies. Insert material: Shall be in accordance with MIL-C-28748. For design feature purposes, this standard takes precedence over procurement documents referenced herein. Reference documents shall be of the issue in effect on date of invitation fo
9、r bid. Cable clamp configuration has optional mounting method. Haterial for jackscrews and guidepins: Corrosion resistance steel per specification .QP-S463 or ASTH-A 582, class 302, 303, 303SE. 304, or 316, except knobs, washers, and spacers shall be either aluminum alloy or corrosion resistance ste
10、el. Finish for jackscrews and guidepins: Passivated per 99-P-35 except knobs, washers, and spacers shall be passivated or anodized. PA Navy EC I hErl I TITLE CONNECTOR. RECTANGULAR. ELECTRICAL I MILITARY STANDARD 0th- curt RkK AND PANEL 4 SIZE-22 SOLDER PIN AF - 85 Am - CR Piocutenami Spoclllcailan MIL-C-28748 CONTACTS MS14012 YIPERSEDESI PAGE 3 OF 3 5935-3136-1 c Licensed by Information Handling Services
