NBN-EN 324-2-1994 3750 《木质板材 板材大小的测定 第2部分：边缘夹角和平直度的测定》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSK-M4D751-A-2008 POLYETHYLENE (PE) FOAM CROSSLINKED CLOSED CELL 50 kg m3 TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯(PE)泡沫化学交联密闭槽 50 kg m3 (与FORD WSS-M99P1111-A一起使用) [使用 FORD .pdf

FORD WSK-M4D752-A-2010 POLYAMIDE (PA) 66 HEAT STABILIZED COOLING AGENT RESISTANT 30% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《30%玻璃纤维增强的耐冷却剂、受.pdf

FORD WSK-M4D753-A-2010 POLYBUTYLENE TEREPHTHALATE (PBT) MODIFIED 20 % GLASS FIBER REINFORCED MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用20%玻璃纤维增强的改性聚对苯二甲.pdf

FORD WSK-M4D753-A2-2010 POLYBUTYLENE TEREPHTHALATE (PBT) MODIFIED 20% GLASS FIBER REINFORCED MOLDING COMPOUND PAINTABLE TO BE USED WITH FORD WSS-M99P1111-A 《可印刷的20%玻璃纤维增强的改性聚对苯二甲.pdf

FORD WSK-M4D754-A-2015 POLYAMIDE (PA) 6 HEAT STABILIZED 15 % GLASS FIBER REINFORCED MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSK-M4D755-A1-2006 THERMOPLASTIC POLYURETHANE ELASTOMER (TPU) 55 DUROMETER D HARDNESS TO BE USED WITH FORD WSS-M99P1111-A 《硬度为55 D的热塑性聚氨酯弹性体(TPU) 与标准FORD WSS-M99P1111-A一起使用.pdf

FORD WSK-M4D755-A2-2006 THERMOPLASTIC POLYURETHANE ELASTOMER (TPU) 40 DUROMETER D HARDNESS TO BE USED WITH FORD WSS-M99P1111-A (Shown on WSK-M4D755-A1)《硬度为40 D的热塑性聚氨酯弹性体(TPU) 与标.pdf

FORD WSK-M4D755-A3-2006 THERMOPLASTIC POLYURETHANE ELASTOMER (TPUR) 65 DUROMETER D HARDNESS MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《硬度65 D的热塑性聚氨酯弹性体(TPUR)成型料 与标准FO.pdf

FORD WSK-M4D758-A1-2010 POLYPROPYLENE (PP) HOMOPOLYMER 30% MINERAL FILLED SELF-EXTINGUISHING MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《30%矿物混合物填充的聚丙烯(PP)自熄灭成型料 与标准FO.pdf