NBN-EN 60095-1-1994 5000 Lead-acid starter batteries Part 1 General requirements and methods of test《铅酸起动电池组 第1部分：一般要求，试验方法》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSS-M4D953-A1-2006 POLYVINYL CHLORIDE (PVC) ALLOY FLEXIBLE 89 DUROMETER A HARDNESS MOLDING COMPOUND EXTERIOR PAINTABLE TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用可印刷硬度为89 A的聚.pdf

FORD WSS-M4D953-A2-2006 POLYVINYL CHLORIDE (PVC) ALLOY FLEXIBLE 76 DUROMETER A HARDNESS MOLDING COMPOUND EXTERIOR PAINTABLE TO BE USED WITH FORD WSS-M99P1111-A (Shown on WSS-M4D9.pdf

FORD WSS-M4D954-A-2015 THERMOPLASTIC POLYOLEFIN ELASTOMER (TEO) 30% MINERAL FILLED COLOR PIGMENTED MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M4D955-A-2012 POLYETHYLENE (PE) HIGH DENSITY MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《高密度聚乙烯(PE)模塑材料 与福特WSS-M99P1111-A 一起使用[使用 福特WRS-M4D955-B]》.pdf

FORD WSS-M4D955-B-2011 POLYETHYLENE (PE) HIGH DENSITY MOLDING COMPOUND NON VISIBLE EXTERIOR UNDERBODY TO BE USED WITH FORD WSS-M99P1111-A 《外部 地面不可视的高密度聚乙烯(PE)模塑材料 与福特WSS-M99P11.pdf

FORD WSS-M4D959-A-2011 POLYPROPYLENE (PP) HOMOPOLYMER 20% CALCIUM CARBONATE FILLED HEAT STABILIZED IMPACT MODIFIED MOLDING COMPOUND 25% MIN POST CONSUMER CONTENT TO BE USED WITH F.pdf

FORD WSS-M4D959-A2-2011 POLYPROPYLENE (PP) HOMOPOLYMER 30% CALCIUM CARBONATE FILLED HEAT STABILIZED 25% MIN POST CONSUMER CONTENT TO BE USED WITH FORD WSS-M99P1111-A 《30%碳酸钙填充热稳定.pdf

FORD WSS-M4D960-A-2006 ABS + POLYAMIDE BLEND (ABS+PA) MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用丙烯腈-丁二烯-苯乙烯共聚物（ABS）+聚酰胺混合物成型料 与标准FORD WSS-M99P1111-A一起使.pdf

FORD WSS-M4D960-A2-2012 ABS + POLYAMIDE 6 BLEND (ABS + PA6) MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf