NC 19-04-26-1985 Occupational Hygiene and Safety tandards System Safeguard of orking Means General Requirements《职业卫生和安全标准系统 工作安全装置手段 一般要求》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSF-M4D767-A-2010 POLYCARBONATE + THERMOPLASTIC COPOLYESTER BLEND (PC + PCTA) FILM TRANSLUCENT TO BE USED WITH FORD WSS-M99P1111-A 《透明的聚碳酸酯+热塑性共聚酯混合物(PC+PCTA)膜 与福特WSS-M99P1.pdf

FORD WSF-M4D770-A-2010 POLYIMIDE (PI) 13% GRAPHITE POWDER 10% PTFE FILLED SINTERED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《13%石墨粉 10%聚四氟乙烯(PTFE)填充的聚酰亚胺(PI)烧结成型料 与标.pdf

FORD WSF-M4D770-A2-2010 POLYIMIDE (PI) 37% GRAPHITE POWDER FILLED SINTERED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《37%石墨粉填充的聚酰亚胺(PI)烧结成型料 与标准FORD WSS-M99P1111-A一起使.pdf

FORD WSF-M4D774-A-2006 POLYETHERSULFONE (PESU) 30% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《30%玻璃纤维增强的聚醚砜（PESU）成型料 与标准FORD WSS-M99P1111-A一起使用.pdf

FORD WSF-M4D774-A2-2006 POLYETHERSULFONE (PESU) 30% GLASS FIBER REINFORCED MOLDING COMPOUND REDUCED FLOW RATE TO BE USED WITH FORD WSS-M99P1111-A (Shown on WSF-M4D774-A)《低流动性的30%.pdf

FORD WSF-M4D779-A-2010 POLYETHYLENE TEREPHTHALATE (PET) 35% GLASS FIBER MICA REINFORCED MOLDING COMPOUND 100% RECYCLED PET TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯对苯二甲酸酯(PET) 35%.pdf

FORD WSF-M4D785-A3-2008 ABS + POLYCARBONATE BLEND (ABS+PC) 12% TiO2 FILLED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《12%二氧化钛填充丙烯腈-丁二烯-苯乙烯+聚碳酸酯(ABS+PC)混物模塑料v和一起使用(FORD.pdf

FORD WSF-M4D786-A-2006 POLYAMIDE (PA) 66 35% LONG GLASS FIBER REINFORCED HEAT STABILIZED IMPACT MODIFIED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A (Use WSB-M4D678-A)《3.pdf

FORD WSF-M4D803-A2-2006 POLYPHENYLENE SULFIDE (PPS) 65% GLASS FIBER MINERAL REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《65%玻璃纤维 矿物增强的聚苯硫醚(PPS)成型料 与标准FORD WS.pdf