1、NEMA Standards PublicationNational Electrical Manufacturers AssociationNEMA WD 7-2011Occupancy Motion Sensors StandardWD 7-2011 Page i NEMA WD 7- 2011 Occupancy Motion Sensors Standard Published by National Electrical Manufacturers Association 1300 N. 17th Street Rosslyn, Virginia 22209 Published Fe
2、bruary 21, 2012 Copyright 2011 by National Electrical Manufacturers Association. All rights including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American Co
3、pyright Conventions. WD 7-2011 Page ii CONTENTS CONTENTS - ii FOREWORD - iii Section 1 GENERAL - 1 1.1 Scope - 1 1.2 Definitions - 1 Section 2 ILLUSTRATIONS - 3 2.1 General - 3 2.2 Minimum Illustration - 3 2.3 Format of Illustration - 3 Section 3 TESTING - 5 3.1 Operating Conditions for Coverage Are
4、a Testing - 5 3.1.1 Indoor Products - 5 3.1.2 Outdoor Products - 5 3.1.3 Test Setup-5 3.2 Major Motion Testing - 6 3.2.1 Test Subject - 6 3.2.2 Test Environment - 6 3.3 Minor Motion Testing - 6 3.3.1 Test Apparatus - 6 3.3.2 Test Environment - 6 3.3.3 Direction of Motion - 6 3.3.4 Setup and Test Pro
5、cedure - 7 ANNEX A- A-1 WD 7-2011 Page iii FOREWORD The purpose of this standard is to promote uniformity for the definition and measurement of characteristics relevant to the use and application of occupancy motion sensors. The standard is not intended to set performance levels. In the preparation
6、of this standard publication, input of users and other interested parties has been sought and evaluated. Inquiries, comments, and proposed or recommended revisions should be submitted to the NEMA Wiring Device Section by contacting the: Vice-President, Engineering National Electrical Manufacturers A
7、ssociation 1300 N. 17th Street Rosslyn, Virginia 22209 This is the first edition of this standard. It was developed from a former technical guide under the same designation. The standards or guidelines presented in a NEMA standards publication are considered technically sound at the time they are ap
8、proved for publication. They are not a substitute for a product sellers or users own judgment with respect to the particular product referenced in the standard or guideline, and NEMA does not undertake to guarantee the performance of any individual manufacturers products by virtue of this standard o
9、r guide. Thus, NEMA expressly disclaims any responsibility for damages arising from the use, application, or reliance by others on the information contained in these standards or guidelines. This standard was developed by the NEMA Wiring Device Section. Section approval of the guide does not necessa
10、rily imply that all section members voted for its approval or participated in its development. At the time it was approved, the NEMA Wiring Device Section was composed of the following members: 2D2C, Inc. Kitchener, ON, Canada BSafe Electrix Manhasset, NY Cooper Wiring Devices Peachtree City, GA Eri
11、cson Manufacturing Company Willoughby, OH Euroloft Inc. Toronto, ON, Canada Hubbell Incorporated Bridgeport, CT Interpower Corporation Oscaloosa, IA KCSM Irvine, CA Leviton Manufacturing Co., Inc. Little Neck, NY Lutron Electronics Company, Inc. Coopersburg, PA Pass & Seymour/Legrand Syracuse, NY Sc
12、hneider Electric Palatine, IL Technology Research Corporation Clearwater, FL Thomas & Bets Corp. Memphis, TN Tyco Electronics Corp Harrisburg, PA TyMac Gilbert, AZ Watt Stopper, Inc./Legrand Santa Clara, CA WD 7-2011 Page A-1 Page ivWD 7-2011 Page 1 Section 1 GENERAL 1.1 SCOPE This standard publicat
13、ion covers the definition and measurement of field of view and coverage characteristics relevant to the use and application of vacancy and occupancy sensors using individual or any combination of passive infrared, ultrasonic, or microwave technology. These sensors are used in systems for control of
14、lighting, heating, ventilating, and air conditioning (HVAC), and other devices. 1.2 DEFINITIONS The definitions below apply to terms used in this guide publication or in manufacturers specification sheets and product literature, or both. Where the terms are used in this guide publication or in a man
15、ufacturers specification sheet or other product literature, the following definitions apply. bypass: the means of forcing loads into “ON“ or “OFF“ condition by circumventing the device. cell: a 3 foot by 3 foot section of the grid. coverage area: the area in which the sensor can detect motion, compr
16、ised of the horizontal and vertical fields of view. energy consumption: total consumption in milliwatts for 1 hour with the controlled load “ON“ for 30 minutes and “OFF“ for 30 minutes. grid: the area in which the sensor is tested divided into 3 foot by 3 foot sections. horizontal field of view: the
17、 area of coverage in a horizontal plane to the sensor while the sensor is mounted in the orientation recommended by the manufacturer. The height of the horizontal field is at a level of 36 1 in. above the ground. immunity to false activation: the ability to ignore external events which are not inten
18、ded to activate the product. initial trigger motion detection: the condition when the sensor is operating in an unoccupied coverage area. line of sight coverage: the ability to detect motion when there is not any object(s) between the motion and sensor to obscure or to block the detection of motion.
19、 maintained motion detection: the condition when the sensor is operating in an occupied coverage area. major motion: movement of a person walking into or through an area. measurement units: degrees for viewing angles feet (m) for distance feet and inches (m) for mounting height feet per second (m/s)
20、 for velocity square feet (m) for coverage area microwave: type of occupancy motion sensor that emits a low power microwave into the area being monitored. The frequency of this wave is between 1 GHz and 100 GHz. Changes in the WD 7-2011 Page 2 reflection pattern caused by motion are received by the
21、sensor and converted into an electrical signal. minor motion: movement of a person sitting at an office desk reaching for a telephone, turning the pages in a book, opening a file folder, picking up a coffee cup, etc. motion detection: a means to determine that the sensor has detected motion. mountin
22、g height: the height above the floor to the center of the sensor. motion sensor: an outdoor sensor that automatically turns lighting on when motion is detected, and off when an outdoor area is vacant. occupancy sensor: an indoor sensor that automatically turns lighting on when occupancy is detected,
23、 and off when the space is vacant. override: the means of modifying the normal detection operation of the device to alter control functions. passive infrared: type of occupancy sensor that uses thermal detectors to absorb the received energy focused on them. A change in energy received by a thermal
24、detector results in a change in detector temperature which results in an electrical signal. The more common thermal detector (the pyroelectric detector) has an output that is proportional to the rate of change of its temperature. Pyroelectric detectors respond to changes in received energy in the 7
25、to 14 micron portion of the electromagnetic spectrum. The detector aperture is converted optically, e.g., by a multi-segment, Fresnel lens array into multiple discrete fields of view that are strategically located throughout the occupancy sensor pattern. When a person moves into or out of a field of
26、 view, the detector experiences a change in received energy, which is converted into an electrical signal. sensitivity: the ability of the sensor to detect the designated magnitude of motion for a given application. time delay: the duration of time from the time the motion was last detected until th
27、e controlled loads are deactivated, e.g., lights turned off, signal given to other equipment, etc. ultrasonic: type of occupancy motion sensor that emits a low power sound into the area being monitored. The sound wave is at a frequency above the range that a person can hear. Changes in the reflectio
28、n pattern caused by motion are received by the sensor and converted into an electrical signal. vacancy sensor: an indoor sensor that automatically turns lighting off when a space is vacant, and requires manual activation of lighting to turn lighting on. vertical field of view: the area of coverage i
29、n a vertical plane to the sensor while the sensor is mounted in the orientation recommended by the manufacturer. volumetric coverage: the ability to detect motion that is generated behind an object that obstructs the line of sight between the motion and the sensor. WD 7-2011 Page 3 Section 2 ILLUSTR
30、ATIONS 2.1 GENERAL The horizontal or vertical fields of view may be illustrated in product literature, specifications, etc. The use of illustration is optional. If any illustration is used, it shall meet the requirements below for minimum illustration and illustration format. 2.1.1 Any manufacturer
31、claiming to have tested or used the WD-7 standard as the criteria for establishing occupancy sensor field of view and coverage characteristics shall publish and make available the measurements of the field of view and coverage characteristics in the format provided under Section 2 of the standard. 2
32、.2 MINIMUM ILLUSTRATION The illustration shall include at least the following information: Mounting height Maximum horizontal coverage angle Dimensions of coverage area Dimensions of room (length, width, height) Floor surface material The manufacturer shall state whether the illustration is for init
33、ial trigger motion detection or for maintained motion detection. 2.3 FORMAT OF ILLUSTRATION The illustration of the horizontal or vertical fields of view for passive infrared and ultrasonic devices shall have the following format: Grid pattern, with a maximum 3x3 ft cell size Crosshatched cells wher
34、e major motion is detected Shaded or solid cells, where minor motion is detected An example illustration is in Figure 2-1. WD 7-2011 Page 4 Figure 2-1 WALL SWITCH PIR PATTERN (3 ft blocks) WD 7-2011 Page 5 Section 3 TESTING 3.1 OPERATING CONDITIONS FOR COVERAGE AREA TESTING 3.1.1 Test Conditions The
35、 test shall be conducted in an indoor environment as described section 3.1.2, regardless of the actual intended operating environment of the sensor. Mounting height and commissioning adjustments shall be per manufacturers instructions, except for high bay sensors. High bay sensors shall be tested at
36、 one or more of the following mounting heights of 20ft, 30ft, 40ft, 50ft & 60ft. There shall be no other people or moving objects in the coverage area. 3.1.2 Test Environment a) The room shall be divided into a square grid with cell dimensions of 3x3 ft. b) The room shall be larger than the test are
37、a such that the tester can walk into the FOV of the sensor. c) Temperature: 1. For any sensors mounted over 10ft, the temperature shall be measured at the sensor and at the ground. 2. For all other sensors, the temperature of the room must be maintained at 70 5F throughout the test, and shall be mea
38、sured at the sensor. d) The humidity of the room during the test shall be recorded. e) The standard method shall test the sensor in a room that is slightly greater in size than the specified coverage area of the sensor. If the coverage area exceeds the size of the test room, an alternate test method
39、 may be followed. The alternate method shall test one half of the field of view, then, by re-positioning the sensor, test the other half of the field of view. The illustration shall note which test method is used. See appendix A for examples of acceptable methods for the alternate test. Note: The al
40、ternate test method is acceptable for: line of sight sensors ultrasonic sensors that have opposing transmit & receive ports, such that the FOV can be divided in half Other types of sensors shall be tested with the standard method. The sensor will be mounted on a surface that is stable and vibration
41、free. 3.1.3 Test Setup a) Prepare a template drawing for the test room. b) Install and wire the sensor in accordance with the manufacturers instructions. c) Record the mounting height. d) For sensors that have adjustable positioning, record the orientation of the sensor and mounting angle. e) Sensor
42、 shall be horizontally leveled for ceiling mount and vertically leveled for the wall mount. f) Allow the sensor to stabilize in accordance with the manufacturers instructions. g) Adjust the sensitivity of the sensor being tested in accordance with the manufacturers instructions. h) Record the temperature of the room at the sensor. i) Record the humidity of the room. WD 7-2011 Page 6 3.2 MAJOR MOTION TESTING 3.2.1 Test Subject The test subject shall meet the following criteria: H
