1、NFPA 204 Standard for Smoke and Heat Venting 2015 Edition NFPA, 1 Batterymarch Park, Quincy, MA 02169-7471, USA An International Codes and Standards Organization 1/14ISBN: 978-145591044-1 (Print)ISBN: 978-145591090-8 (PDF)IMPORTANT NOTICES AND DISCLAIMERS CONCERNING NFPASTANDARDS NOTICE AND DISCLAIM
2、ER OF LIABILITY CONCERNING THE USE OF NFPA STANDARDSNFPAcodes, standards, recommended practices, and guides (“NFPA Standards”), of which the document contained herein is one, are developed through a consensus standards development process approved by the American National Standards Institute. This p
3、rocess brings together volunteers representing varied viewpoints and interests to achieve consensus on fire and other safety issues. While the NFPA administers the process and establishes rules to promote fairness in the development of consensus, it does not independently test, evaluate, or verify t
4、he accuracy of any information or the soundness of any judgments contained in NFPA Standards.The NFPA disclaims liability for any personal injury, property or other damages of any nature whatsoever, whether special, indirect, consequential or compensatory, directly or indirectly resulting from the p
5、ublication, use of, or reliance on NFPA Standards. The NFPA also makes no guaranty or warranty as to the accuracy or completeness of any information published herein.In issuing and making NFPA Standards available, the NFPA is not undertaking to render professional or other services for or on behalf
6、of any person or entity. Nor is the NFPA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonab
7、le care in any given circumstances.The NFPA has no power, nor does it undertake, to police or enforce compliance with the contents of NFPA Standards. Nor does the NFPA list, certify, test, or inspect products, designs, or installations for compliance with this document. Any certification or other st
8、atement of compliance with the requirements of this document shall not be attributable to the NFPA and is solely the responsibility of the certifier or maker of the statement.REMINDER: UPDATING OF NFPA STANDARDSUsers of NFPA codes, standards, recommended practices, and guides (“NFPA Standards”) shou
9、ld be aware that NFPA Standards may be amended from time to time through the issuance of Tentative Interim Amendments or corrected by Errata. An official NFPA Standard at any point in time consists of the current edition of the document together with any Tentative Interim Amendment and any Errata th
10、en in effect.In order to determine whether an NFPA Standard has been amended through the issuance of Tentative Interim Amendments or corrected by Errata, visit the Document Information Pages on NFPAs website. The Document Information Pages provide up-to-date, document specific information including
11、any issued Tentative Interim Amendments and Errata.To access the Document Information Page for a specific NFPA Standard, go to http:/www.nfpa.org/docinfo to choose from the list of NFPA Standards or use the search feature on the right to select the NFPA Standard number (e.g., NFPA 101). In addition
12、to posting all existing Tentative Interim Amendments and Errata, the Document Information Page also includes the option to sign-up for an “Alert” feature to receive an email notification when new updates and other information are posted regarding the document.1/14IMPORTANT NOTICES AND DISCLAIMERS CO
13、NCERNING NFPASTANDARDS ADDITIONAL NOTICES AND DISCLAIMERSUpdating of NFPA Standards Users of NFPA codes, standards, recommended practices, and guides (“NFPA Standards”) should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to t
14、ime through the issuance of Tentative Interim Amendments or corrected by Errata. An official NFPA Standard at any point in time consists of the current edition of the document together with any Tentative Interim Amendments and any Errata then in effect. In order to determine whether a given document
15、 is the current edition and whether it has been amended through the issuance of Tentative Interim Amendments or corrected through the issuance of Errata, consult appropriate NFPA publications such as the National Fire CodesSubscription Service, visit the NFPA website at www.nfpa.org, or contact the
16、NFPA at the address listed below.Interpretations of NFPA StandardsA statement, written or oral, that is not processed in accordance with Section 6 of the Regulations Governing the Development of NFPA Standards shall not be considered the official position of NFPA or any of its Committees and shall n
17、ot be considered to be, nor be relied upon as, a Formal Interpretation.PatentsThe NFPA does not take any position with respect to the validity of any patent rights referenced in, related to, or asserted in connection with an NFPA Standard. The users of NFPA Standards bear the sole responsibility for
18、 determining the validity of any such patent rights, as well as the risk of infringement of such rights, and the NFPA disclaims liability for the infringement of any patent resulting from the use of or reliance on NFPA Standards.NFPA adheres to the policy of the American National Standards Institute
19、 (ANSI) regarding the inclusion of patents in American National Standards (“the ANSI Patent Policy”), and hereby gives the following notice pursuant to that policy:NOTICE: The users attention is called to the possibility that compliance with an NFPA Standard may require use of an invention covered b
20、y patent rights. NFPA takes no position as to the validity of any such patent rights or as to whether such patent rights constitute or include essential patent claims under the ANSI Patent Policy. If, in connection with the ANSI Patent Policy, a patent holder has filed a statement of willingness to
21、grant licenses under these rights on reasonable and nondiscriminatory terms and conditions to applicants desiring to obtain such a license, copies of such filed statements can be obtained, on request, from NFPA. For further information, contact the NFPA at the address listed below.Law and Regulation
22、sUsers of NFPA Standards should consult applicable federal, state, and local laws and regulations. NFPA does not, by the publication of its codes, standards, recommended practices, and guides, intend to urge action that is not in compliance with applicable laws, and these documents may not be constr
23、ued as doing so.CopyrightsNFPA Standards are copyrighted. They are made available for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of safe practices and methods. B
24、y making these documents available for use and adoption by public authorities and private users, the NFPA does not waive any rights in copyright to these documents.Use of NFPA Standards for regulatory purposes should be accomplished through adoption by reference. The term “adoption by reference” mea
25、ns the citing of title, edition, and publishing information only. Any deletions, additions, and changes desired by the adopting authority should be noted separately in the adopting instrument. In order to assist NFPA in following the uses made of its documents, adopting authorities are requested to
26、notify the NFPA (Attention: Secretary, Standards Council) in writing of such use. For technical assistance and questions concerning adoption of NFPA Standards, contact NFPA at the address below.For Further InformationAll questions or other communications relating to NFPA Standards and all requests f
27、or information on NFPA procedures governing its codes and standards development process, including information on the procedures for requesting Formal Interpretations, for proposing Tentative Interim Amendments, and for proposing revisions to NFPA standards during regular revision cycles, should be
28、sent to NFPA headquarters, addressed to the attention of the Secretary, Standards Council, NFPA, 1 Batterymarch Park, P.O. Box 9101, Quincy, MA 02269-9101; email: stds_adminnfpa.orgFor more information about NFPA, visit the NFPA website at www.nfpa.org. All NFPA codes and standards can be viewed at
29、no cost at www.nfpa.org/freeaccess.Copyright 2014 National Fire Protection Association. All Rights Reserved.NFPA204Standard forSmoke and Heat Venting2015 EditionThis edition of NFPA 204, Standard for Smoke and Heat Venting, was prepared by the TechnicalCommittee on Smoke Management Systems. It was i
30、ssued by the Standards Council on November11, 2014, with an effective date of December 1, 2014, and supersedes all previous editions.This edition of NFPA 204 was approved as an American National Standard on December 1,2014.Origin and Development of NFPA 204This project was initiated in 1956 when the
31、 NFPA Board of Directors referred the subject tothe Committee on Building Construction. A tentative guide was submitted to NFPA in 1958.Revised and tentatively adopted in 1959 and again in 1960, the guide was officially adopted in1961. In 1968, a revised edition was adopted that included a new secti
32、on, Inspection andMaintenance.In 1975, a reconfirmation action failed as concerns over use of the guide in conjunctionwith automatic sprinklered buildings surfaced. Because of this controversy, work on a revisionto the guide continued at a slow pace.The Technical Committee and Subcommittee members a
33、greed that the state of the arthad progressed sufficiently to develop improved technology-based criteria for design of vent-ing; therefore, the 1982 edition of the document represented a major advance in engineeredsmoke and heating venting, although reservations over vent and sprinkler applications
34、stillexisted.At the time the guide was formulated, the current venting theory was considered unwieldyfor this format; consequently, the more adaptable theory as described herein was adopted.Appreciation must be extended to Dr. Gunnar Heskestad at the Factory Mutual ResearchCorporation (now FM Global
35、) for his major contribution to the theory applied in this stan-dard, which is detailed in Annex B.The 1985 edition again revised Chapter 6 on the subject of venting in sprinklered build-ings. Test data from work done at the Illinois Institute of Technology Research, which hadbeen submitted to the C
36、ommittee as part of a public proposal, did not permit consensus to bedeveloped on whether sprinkler control was impaired or enhanced by the presence of auto-matic roof vents of typical spacing and area. The revised wording of Chapter 6 encouragedthe designer to use the available tools and data refer
37、enced in the document while the use ofautomatic venting in sprinklered buildings was under review.The 1991 edition made minor changes to Chapter 6 to acknowledge that a design basisexisted for using sprinklers and automatic heat venting together but that such had not re-ceived wide recognition.The 1
38、998 edition represented a complete revision of the guide. The rewrite deleted theprevious tables that listed vent areas and incorporated engineering equations and referencedcomputer models, such as LAVENT and DETACT, to provide the designer with the necessarytools to develop vent designs based on pe
39、rformance objectives. This rewrite was based exten-sively on state-of-the-art technology published in the references. In many cases, the authors ofthese references participated in the task groups rewrite efforts.The 2002 edition of NFPA 204 was converted from a guide to a standard, thus implement-in
40、g mandatory requirements and updated language. The document was also updated to meetManual of Style for NFPA Technical Committee Documents requirements.2041NFPA and National Fire Protection Association are registered trademarks of the National Fire Protection Association, Quincy, Massachusetts 02169
41、.The 2007 edition included a number of technical changes. New provisions on air entrainment into the fire plume,the effect of wind on the location of air vents, sizing of air paths, air velocity limitations, and plugholing were provided.Information on the use of vents as air inlets and a better desc
42、ription of the smoke layer interface were added. Revisionswith regard to how heat release rates, discharge coefficients, exhaust rates, and the number of exhaust inlets are to bedetermined were incorporated. Reference to international standards on vents, mechanical smoke extract, and draftcurtains,
43、as well as updated annex text on recent research efforts, were provided.The 2012 edition was updated to include additional requirements and annex material for venting in sprin-klered buildings.The 2015 edition includes revised provisions on draft curtains. These requirements create consistency withN
44、FPA 92.2042 SMOKE AND HEAT VENTING2015 EditionTechnical Committee on Smoke Management SystemsRandolph W. Tucker, Chairccrd partners, TX SESanjay Aggarwal The RJA Group, Inc., CA SEElyahu Avidor, Tel Aviv, Israel RTRep. Standards Institution of IsraelFlora F. Chen, Hayward Fire Department, CA EPaul D
45、avid Compton, Colt International, Ltd., UnitedKingdom MRichard J. Davis, FM Global, MA IKevin L. Derr, U.S. Architect of the Capitol, DC EMichael Earl Dillon, Dillon Consulting Engineers, Inc.,CA SEKelly Eisenstein, City Of San Diego, CA EDouglas H. Evans Clark County Building Department,NV EMichael
46、 J. Ferreira, Hughes Associates, MD SEBrian Green, Viking Corporation, MI MRep. National Fire Sprinkler AssociationGeoffrey Harris, Smoke and Fire EngineeringTechnology Ltd., United Kingdom SERep. ISO TC on Smoke and Heat Control Systems andComponentsJohn E. Kampmeyer, Sr., Triad Fire ProtectionEngi
47、neering Corporation, PA SERep. National Society of Professional EngineersDavid A. Killian, Walt Disney Parks FM 4430, Ap-proval Standard for Heat and Smoke Vents; or other approved,nationally recognized standards.5.2 Vent Design Constraints.5.2.1* The means of vent actuation shall be selected with r
48、e-gard to the full range of expected ambient conditions.5.2.2* Vents shall consist of a single unit (vent), in which theentire unit (vent) opens fully with the activation of a single detec-tor, or multiple units (vents) in rows or arrays (ganged vents) inwhich the units (vents) open simultaneously w
49、ith the activationof a single heat detector, a fusible link, a smoke detector, a sprin-kler waterflow switch, or other means of detection to satisfy theventing requirements for a specific hazard.5.2.3* Where the hazard is localized, vents shall open directlyabove such hazard.5.2.4 Vents, and their supporting structure and means of ac-tuation, shall be designed so that they can be inspected visu-ally after installation.5.3 Methods of Operation.5.3.1* Normally, closed vents shall be designed to open auto-matically in a fire to meet design objectives o
