ONORM S 1393 Teil 71-1987 Rimmed rifle cartridge and Chamber caliber 369 N E Purdey《镶边步枪子弹和枪膛 口径 369 N E Purdey》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

CSN 25 4036-1973 Screw gauges Minimum and maximum check plug for solid NOT GO screw ring gauge Metric screw thread diameter 1 mm to 100 mm《螺纹规 非穿过型实心螺纹环规的最小与最大检测插塞 直径为1mm 到 100 mm的.pdf

CSN 25 4039-1973 Screw gauges Wear check plug for solid or adjustable NOT GO screw ring gauge Metric screw thread diameter 1 mm to 100 mm《螺纹规 实心可调非通过式环螺钉规耐磨检查插塞 直径为1 mm 到 100 mm的公制.pdf

CSN 25 4045-1973 GO and NOT GO screw calliper gauge Metric thread of diameter over 3 mm up to 100 mm《穿过和非穿过型螺纹规 直径为3 mm到100 mm的公制螺纹》.pdf

CSN 25 4046-1973 Setting plug for GO and NOT GO screw calliper gauge Metric thread diameter over 3 mm up to 100 mm《穿过型及非穿过型螺丝两脚规底座插栓 直径3mm到100 mm的公制螺纹》.pdf

CSN 25 4047-1973 NOT GO screw calliper gauge Metric thread of diameter over 3 mm up to 100 mm《非穿过型螺纹规 直径3 mm到00 mm的公制螺纹》.pdf

CSN 25 4048-1985 Setting plug for NOT GO screw calliper gauge Metric thread of diameter over 3 mm up to 100 mm《非穿过型螺丝两脚规定位插塞 直径为3mm到100 mm的公制螺纹》.pdf

CSN 25 4050-1986 Screw gauges Limit screw plug gauges Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 止动螺钉插塞规 直径为G 1 8 到G3 1 2的圆柱形导管螺纹》.pdf

CSN 25 4055-1986 Screw gauges Solid GO screw ring gauges Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 穿过型实心环首螺钉规直径为1 8 - G 3 1 2的圆柱形导管螺纹》.pdf

CSN 25 4056-1986 Screw gauges Minimum and maximum check plugs for solid GO screw ring gauge Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 实心穿过型环首螺钉规最小及最大检测插栓 直径为1 8 - G 3 1 .pdf