1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref
2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2017 SAE InternationalAll rights reserved. No part of this publi
3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out
4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on thisTechnical Report, please visithttp:/standards.sae.org/AMS1428/2AEROSPACEMATERIAL SPECIFICATIONAMS1428/2Issued 2017-02Fluid, Aircraft Deicing/Anti-Icing, Non-Newt
5、onian(Pseudoplastic), SAE Types II, III, and IV Non-Glycol BasedRATIONALEThis document has been produced to identify the generic product of Fluid, Aircraft Deicing/Anti-Icing, Non-Newtonian(Pseudoplastic), SAE Types II, III, and IV.Non-Glycol is defined under 3.1.1 in AMS1428J.1. SCOPE1.1 FormThe fo
6、undation specification (AMS1428J) and the category specifications (AMS1428/1 and AMS1428/2) cover deicing/anti-icing materials in the form of a fluid.1.1.1 Foundation and Category SpecificationsThe foundation specification establishes the requirements for all Fluid, Aircraft Deicing/Anti-Icing, Non-
7、Newtonian(Pseudoplastic), SAE Types II, III, and IV and defines the terms Glycol (Conventional and Non-Conventional) and Non-Glycol and contains technical and other requirements that apply to both Glycol (Conventional and Non-Conventional) and Non-Glycol based fluids.The category specification AMS14
8、28/1 covers Glycol (Conventional and Non-Conventional) based fluids whereas the category specification AMS1428/2 covers Non-Glycol based fluids.1.2 Other Scope RequirementsOther scope requirements are set in AMS1428J.SAE INTERNATIONAL AMS1428/2 Page 2 of 32. APPLICABLE DOCUMENTSThe issue of the foll
9、owing documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no supersedin
10、g document has been specified, the last published issue of that document shall apply. 2.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USAand Canada) or +1 724-776-4970 (outside USA), www.sae.org.AMS1428J Fluid, Aircra
11、ft Deicing/Anti-Icing, Non-Newtonian (Pseudoplastic), SAE Types II, III, and IVAMS1428/1 Fluid, Aircraft Deicing/Anti-Icing, Non-Newtonian (Pseudoplastic), SAE Types II, III, and IV. Glycol(Conventional and Non-Conventional) BasedARP1917A Clarification of Terms Used in Aerospace Metals Specification
12、s3. TECHNICAL REQUIREMENTS (SEE SECTION 3 OF AMS1428J)The technical requirements for AMS1428/2 Fluid, Aircraft Deicing/Anti-Icing, Non-Newtonian (Pseudoplastic), SAE Types II, III, and IV Non-Glycol are set in the foundation specification AMS1428J.4. QUALITY ASSURANCE PROVISIONS (SEE SECTION 4 OF AM
13、S1428J)The quality assurance provisions for SAE AMS1428/2 Fluid, Aircraft Deicing/Anti-Icing, Non-Newtonian (Pseudoplastic), SAE Types II, III, and IV Non-Glycol based are set in the foundation specification AMS1428J.5. PREPARATION FOR DELIVERY (SEE SECTION 5 OF AMS1428J)The preparation for delivery
14、 for SAE AMS1428/2 Fluid, Aircraft Deicing/Anti-Icing, Non-Newtonian (Pseudoplastic), SAE Types II, III, and IV Non-Glycol based are set in the foundation specification AMS1428J.6. ACKNOWLEDGMENT (SEE SECTION 6 OF AMS1428J)7. REJECTIONSSee Section 7 of AMS1428J.8. SIMILAR SPECIFICATIONSSee Section 8
15、 of AMS1428J.9. NOTES9.1 Revision IndicatorA change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicat
16、es a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only.SAE INTERNATIONAL AMS1428/2 Page 3 of 39.2 Purchase DocumentPurchase documents should specify not less than the following:AMS1428/2Size and type of containers desiredQuantity desiredPackaging, requirements (see 5.1.4 of AMS1428J).PREPARED BY AMS COMMITTEE “G-12ADF”
