1、 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS3050/2 AEROSPACE MATERIAL SPECIFICATION AMS3050 /2 Issued 2017-12 Performance Specification
5、Anti-Seize Thread Compound, High Temperature Aluminum Only RATIONALE This document has been revised to distinguish this foundation specification (AMS3050) and the associated category specifications (AMS3050/1 through AMS3050/9) and to classify different anti-seize greases conforming to this specific
6、ation by the type of anti-seize additive. The category specifications have been added to the Applicable Documents section. 1. SCOPE 1.1 Form The foundation specification (AMS3050) and this category specification (AMS3050/2) cover anti-seize greases conforming to the requirements, but using the anti-
7、seize ingredient Aluminum only. 1.1.1 Foundation and Category Specifications The foundation specification establishes the main requirements for all anti-seize greases conforming to the foundation specification. The category specification AMS3050/2 covers anti-seize greases conforming to AMS3050 and
8、using an Aluminum anti-seize additive. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document i
9、ssue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (insid
10、e USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS3050 Performance Specification Anti-Seize Thread Compound, High Temperature ARP1917A Clarification of Terms Used in Aerospace Metals Specifications SAE INTERNATIONAL AMS3050/2 Page 2 of 2 3. TECHNICAL REQUIREMENTS See Section 3 of A
11、MS3050. Only Aluminum based anti-seize additives shall be used. The technical requirements for AMS3050/2, Performance Specification Anti-Seize Thread Compound, High Temperature Aluminum Only, are detailed in the foundation specification, AMS3050. 4. VERIFICATION See Section 4 of AMS3050. The Verific
12、ation Process for AMS3050/2, Performance Specification Anti-Seize Thread Compound, High Temperature Aluminum Only, is set in the foundation specification, AMS3050. 5. QUALITY ASSURANCE PROVISIONS See Section 5 of AMS3050. The Quality Assurance Provisions for AMS3050/2, Performance Specification Anti
13、Seize Thread Compound, High Temperature Aluminum Only, are set in the foundation specification, AMS3050. 6. PREPARATION FOR DELIVERY See Section 6 of AMS3050. The preparation for delivery for AMS3050/2, Performance Specification Anti-Seize Thread Compound, High Temperature Aluminum Only, is set in
14、the foundation specification, AMS3050. 7. ACKNOWLEDGMENT See Section 7 of AMS3050. 8. REJECTIONS See Section 8 of AMS3050. 9. NOTES 9.1 Revision Indicator A change bar (I) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes
15、 have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 9.2 Purchase Document Purchase documents should specify not less than the following: AMS3050/2 Size and type of containers desired Quantity desired Packaging, requirements (see Section 6 of AMS3050) PREPARED BY AMS COMMITTEE “M”
