1、 The Engineering SocietyFor Advancing MobilityLand Sea Air and SpaceAEROSPACEI N T E R N A T I O N A L MATERIAL400 Commonwealth Drive, Warrendale, PA 15096-0001SPECIFICATIONSubmitted for recognition as an American National StandardREVAMS-3779/1 AIssued 1984-07-01Revised 1990-07-01Superseding AMS-377
2、9/1TAPE, ADHESIVE, PRESSURE-SENSITIVEThermal Radiation Resistant, Aluminum Foil/Glass Cloth1. SCOPE:1.1 Form: This specification covers thermal radiation resistant material in theform of tape with pressure-sensitive adhesive.1.2 Application: Primarily for use on radiation screens where weight andfle
3、xibility are not critical factors. See AMS-3779/2 for lighter weight andmore flexibility.2. APPLICABLE DOCUMENTS: See AMS-3779.3. TECHNICAL REQUIREMENTS:3.1 Basic Specification: The complete requirements for procuring the tapedescribed herein shall consist of this document and the latest issue of th
4、ebasic specification, AMS-3779.3.2 Material: Shall be as follows:base fabric of AMS-3824 glass cloth, Style 108 or Style 1080, by means ofa pressure-sensitive adhesive.shall require no solvent, heat, or other preparation prior to or afterapplication to clean, dry surfaces. There shall be no liner co
5、vering theadhesive.3.2.3 Color: The tape backing shall have a shiny silver appearance.SAE Technical Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences.The use of this report is entirely voluntary, and its applicability and suitabilit
6、y for any particular use, including any patent infringementarising therefrom, is the sole responsibility of the user.“SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites yourwritten comments and suggestions.Copyright 1990
7、 Society of Automotive Engineers, Inc.All rights reserved. Printed in U.S.A.3.2.1 Backing: Shall be aluminum foil conforming to AMS-4001 laminated to a3.2.2 Adhesive: Shall be a pressure-sensitive silicone polymer. The adhesiveCopyright SAE International Provided by IHS under license with SAENot for
8、 ResaleNo reproduction or networking permitted without license from IHS-,-AMS-3779/1 Revision A3.3 Properties: Tape shall conform to the following requirements, determined onsamples from rolls conditioned for not less than 24 hours at 23C 2(73F 4) and 50% 5 relative humidity and tested in accordance
9、 with testmethods specified in AMS-3779.3.3.1 Thickness, maximum 0.0095 inch (0.241 mm)3.3.2 Tensile Strength, minimum 75 pounds force per inch of width(1313 N/100 mm of width)3.3.3 Elongation. minimum 2%3.3.4 Weight, maximum 0.11 ounce per 12 square inches(3.1 grams per 7742 mm)3.3.5 Adhesion to St
10、eel. minimum3.3.5.1 Initial 20 ounces force per inch of width(22 N/100 mm of width)3.3.5.2 After exposure to 25 ounces force per inch of width260C 5 (500F 9) (27 N/100 mm of width)3.3.5.3 After exposure to 15 ounces force per inch of width-55C 1 (-67F 2) (16 N/100 mm of width)3.3.6 Thermal Radiation
11、 Resistance: There shall be no direct thermaltransmission, no visible damage, no noticeable loss of adhesion, and novisible light transmission.4. QUALITY ASSURANCE PROVISIONS: See AMS-3779.5. PREPARATION FOR DELIVERY: See AMS-3779.6. ACKNOWLEDGMENT: See AMS-3779.7. REJECTIONS: See AMS-3779.8. NOTES: See AMS-3779.- 2 -Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-
