1、SAE-AMS-T-22085ADOPTION NOTICESAE-AMS-T-22085, “TAPES, PRESSURE-SENSITIVE, ADHESIVE,PRESERVATION AND SEALING“, was adopted on 10-SEP-99 for use bythe Department of Defense (DoD). Proposed changes by DoDactivities must be submitted to the DoD Adopting Activity:Commander, Naval Air Warfare Center, Air
2、craft Division, Code414100B120-3, Highway 547, Lakehurst, NJ 08733-5100. Copies ofthis document may be purchased from the Society of AutomotiveEngineers 400 Commonwealth Drive Warrendale, Pennsylvania, UnitedStates, 15096-0001. http:/www.sae.org/_Custodians: Adopting Activity:Navy - ASArmy - GLNavy
3、- ASAir Force - 11Reviewer Activities:Army - CR4, EA, MR, SMAir Force - 99FSC 7510DISTRIBUTION STATEMENT A: Approved for public release; distributionis unlimited.SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering scien
4、ces. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed,
5、 revised, or cancelled. SAE invites your written comments and suggestions.Copyright 1999 Society of Automotive Engineers, Inc.All rights reserved. Printed in U.S.A.QUESTIONS REGARDING THIS DOCUMENT: (724) 772-7121 FAX: (724) 776-0243TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX: (724) 776-0790SAE WE
6、B ADDRESS: http:/www.sae.org400 Commonwealth Drive, Warrendale, PA 15096-0001AEROSPACE MATERIAL SPECIFICATIONAMS-T-22085Issued JUN 1999Tapes, Pressure-Sensitive, Adhesive,Preservation and SealingFSC 7510NOTICEThis document has been taken directly from U.S. Military Specification MIL-T-22085E and con
7、tains only minor editorial and format changes required to bring it into conformance with the publishing requirements of SAE technical standards. The initial release of this document is intended to replace MIL-T-22085E. Any part numbers established by the original specification remain unchanged.The o
8、riginal Military Specification was adopted as an SAE standard under the provisions of the SAE Technical Standards Board (TSB) Rules and Regulations (TSB 001) pertaining to accelerated adoption of government specifications and standards. TSB rules provide for (a) the publication of portions of unrevi
9、sed government specifications and standards without consensus voting at the SAE Committee level, and (b) the use of the existing government specification or standard format.Under Department of Defense policies and procedures, any qualification requirements and associated qualified products lists are
10、 mandatory for DOD contracts. Any requirement relating to qualified products lists (QPLs) has not been adopted by SAE and is not part of this SAE technical document.AMS-T-22085 SAE AMS-T-22085- 2 -1. SCOPE:1.1 Scope: This specification establishes the requirements for pressure-sensitive adhesive tap
11、es designed for exterior preservation and sealing of military vehicles, aircraft, missiles and other related equipment during handling, shipment and storage.1.2 Classification: The tapes shall be of the following types, as specified (see 6.2c):Type II - For use with or without overcoating (see 6.1.1
12、)Type IV - For use without overcoating; for extended time periods (see 6.1.2).1.2.1 Cross reference: Relationship of the types of tapes specified in previous revisions of this specification are detailed in 6.6.2. APPLICABLE DOCUMENTS: The following publications, of the issue in effect on date of inv
13、itation for bids or request for proposal, form a part of this specification to the extent specified herein.2.1 U.S. Government Publications: Available from DODSSP, Subscription Services Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.L-T-80 Tape, Pressure-Sensitive Adhesive (Alumi
14、num-Backed)QQ-A-250/5 Aluminum Alloy Alclad 2024, Plate and SheetPPP-T-680 Tape, Pressure-Sensitive Adhesive, Packaging and Packing ofMIL-C-6799 Coatings, Sprayable, Strippable, Protective, Water EmulsionMIL-A-8625 Anodic Coatings, for Aluminum and Aluminum AlloysMIL-P-23377 Primer Coatings, Epoxy,
15、High SolidsMIL-C-23760 Coating, Sprayable, Strippable, Protective, for Packaging of Weapon Systems and Components, Application ofMIL-C-83286 Coating, Urethane, Aliphatic Isocyanate, for Aerospace ApplicationsMIL-C-85285 Coating: Polyurethane, High-solidsFED-STD-595 Colors Used in Government Procurem
16、entMS20470 Rivet, Solid-Universal Head, Aluminum Alloy and Titanium Columbian AlloyAMS-T-22085 SAE AMS-T-22085- 3 -2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor, West Conshohocken, PA 19428-2959.ASTM D 740 Methyl Ethyl KetoneASTM D 2860 Tape, Pressure-Sensitive Tape, to Fiberboard at 9
17、0-Deg. Angle and Constant Stress, Adhesion ofASTM D 3330 Tape, Pressure-Sensitive Tape at 180 Degree Angle, Peel Adhesion ofASTM D 3611 Tapes, Pressure-Sensitive, Accelerated Aging ofASTM D 3654 Tapes, Pressure-Sensitive, Holding Power ofASTM D 3715 Tapes, Pressure-Sensitive, Quality Assurance ofAST
18、M D 3759 Tape, Pressure-Sensitive, Tensile Strength and Elongation ofASTM D 3811 Tape, Pressure-Sensitive, Unwind Force ofASTM D 3816 Tape, Pressure-Sensitive, Water Penetration Rate ofASTM D 3833 Tape, Pressure-Sensitive, Water Vapor Transmission of2.3 SAE Publications: Available from SAE, 400 Comm
19、onwealth Drive, Warrendale, PA 15096-0001.AMS 4375 Magnesium Alloy Sheet and Plate 3.0Al-1.0Zn (AZ 31B-0) Annealed and Recrystallized2.4 Order of precedence: In the event of a conflict between the text of this document and the references cited herein (except for related associated detail specificati
20、ons, specification sheets or MS standards), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.3. REQUIREMENTS: 3.1 Qualification: The tapes furnished under this specification shall b
21、e products which are authorized by the qualifying activity for listing on the applicable qualified products list at the time of award of contract (see 4.3 and 6.4).3.2 Materials: The materials used in the construction of the pressure-sensitive adhesive tape shall be such as to assure performance of
22、the tape over the temperature range of -54 to 52C (-65 to 125F) and shall conform to the requirements of this specification.AMS-T-22085 SAE AMS-T-22085- 4 -3.2.1 Adhesive: The adhesive for both type II and type IV tapes shall be pressure-sensitive, water-insoluble, homogeneous and coated in a smooth
23、 and evenly distributed layer on one side of the backing, and shall require no solvent, moisture, heat or other preparation prior to or after application to clean, dry surfaces.3.2.2 Backing: Type II tape backing shall be black plastic of single ply construction. The type IV backing shall be a polyv
24、inyl fluoride film with a minimum thickness of 0.002 inches.3.3 Finished tape: 3.3.1 Rolls: The tape shall be furnished in evenly and uniformly wound rolls, adhesive side in, on cores made of paper fiber or non-fibrous plastic. The core shall have sufficient rigidity to prevent distortion of the rol
25、l under normal conditions of transportation, storage, and use. The inside diameter of the core shall be 3 +0.063, -0 inches. The adhesive shall not be covered with a liner.3.3.1.1 Marking of rolls: Each roll of tape shall be marked in or on the edge of the core with numerals or letters indicating th
26、e month and year of manufacture. In addition, the manufacturers name and designation of the product and the specification number shall appear in the core.3.3.2 Length: Unless otherwise specified in the contract or order, type II tape shall be furnished in 36 yard rolls and type IV tape shall be furn
27、ished in 72 yard rolls (see 6.2g). Each roll shall consist of a single length of tape, except that any roll may contain not more than three splices. The splices shall be made in such a manner that they will not separate when the roll is being unwound for inspection, or during application.3.3.3 Width
28、: The width of the rolls shall be 1, 2, 3, or 4 inches, or other commercially available widths, as specified, in the contract or purchase order (see 6.2e). A tolerance of plus or minus 0.031 inch shall be allowed in each width.3.3.4 Color: The color of type II tape shall be black. Unless otherwise s
29、pecified in the contract (see 6.2h), type IV tape shall be any color chosen by the manufacturer, except black.3.4 Performance: 3.4.1 Visual examination: When visually examined as specified, the tape shall conform to the requirements of 3.2 and 3.3 of this specification.3.4.2 Physical properties: The
30、 tape shall comply with the physical property requirements listed in table I, when tested as specified herein.3.4.3 Service (type II and type IV): When required by the qualifying activity, the tape shall be tested as specified in 4.6.11 and shall show satisfactory performance under service condition
31、s.AMS-T-22085 SAE AMS-T-22085- 5 -TABLE I. Physical properties.AMS-T-22085 SAE AMS-T-22085- 6 -TABLE I. - Physical Properties - Continued.3.5 Workmanship: The tape shall be free from foreign matter and defects that may impair its serviceability or appearance. The adhesive shall be a smooth uniform c
32、oating, covering the entire area of one side of the backing. The edges of the tape shall be straight, true and unbroken.4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for inspection: Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance
33、of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the
34、 Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements.4.1.1 Responsibility for compliance: All items shall meet all requirements of
35、 sections 3 and 5. The inspection set forth in this specification shall become part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or
36、 supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, ei
37、ther indicated or actual, nor does it commit the Government to acceptance of defective material.AMS-T-22085 SAE AMS-T-22085- 7 -4.2 Classification of inspections: The inspection requirements specified herein are classified as follows:a. Qualification inspection (see 4.3).b. Quality conformance inspe
38、ction (see 4.4).4.3 Qualification inspection: Qualification inspection shall consist of examinations and tests for all the requirements of this specification.4.3.1 Qualification sampling instructions: Qualification inspection samples shall consist of at least two rolls each of 1 inch and 2 inch wide
39、 tape of the type for which qualification is desired. The samples shall be accompanied by a certified test report prepared either by the manufacturer or an independent laboratory approved by the Government. The test report shall include the test results of all tests as required by 4.3. In addition,
40、the panels that had been exposed to accelerated outdoor exposure, with the applied tape, shall be forwarded along with the test report from the accelerated outdoor exposure facility. Information such as a brief description of the components or raw materials used in the manufacture of the tape and th
41、e address(es) of the plant(s) of manufacture shall be furnished. The samples, the test report and the test panels shall be forwarded to: Commanding Officer, Naval Air Warfare Center, Code 4.3.4.1, Box 5152, Warminster, PA 18974-0591, plainly identified by attached markings with the following informa
42、tion:Samples for Qualification testsTAPES, PRESSURE-SENSITIVE, ADHESIVE, PRESERVATION AND SEALINGManufacturers NameManufacturers Code No.TypeDate of manufacture (month and year)Submitted by (name) (date) for Qualification in accordance with therequirements of MIL-T-22085E Under Authorization (Refere
43、nceAuthorization Letter)4.3.2 Retention of qualification: In order to retain qualification of products approved for listing on the qualified products list (QPL), the manufacturer shall verify by certification to the qualifying activity that his product complies with the requirements of this specific
44、ation. The time of periodic verification by certification shall be in two year interval and shall be initiated by the Government. The Government reserves the right to re-examine the qualified product whenever deemed necessary to determine that the product continues to meet any or all of the specific
45、ation requirements.AMS-T-22085 SAE AMS-T-22085- 8 -4.4 Quality conformance inspection: Quality conformance inspection shall consist of the examinations and tests specified in table II.TABLE II. Quality conformance inspection.4.4.1 Tape examination: Lot formations, sampling, examinations, and accept/
46、fail criteria shall be as specified in Section 6.3 of ASTM D 3715.4.4.2 Tape testing: Lot formation, sampling and tests for quality conformance inspection in table II shall be as specified in Section 6.4 of ASTM D 3715. There shall be no defects.4.4.3 Report: Upon completion of the quality conforman
47、ce inspection, the Government activity responsible for conducting the inspection program (see 6.2i) shall report the results of tests with recommendations to the contracting officer.4.5 Testing conditions: Conditioning and testing of the rolls of tape shall be in accordance with the applicable test
48、method.4.6 Test methods: 4.6.1 ASTM test methods: ASTM test methods, without exceptions, shall be used for test methods specified in table III.AMS-T-22085 SAE AMS-T-22085- 9 -TABLE III. ASTM test methods.4.6.2 Visual examination: The rolls of tape shall be visually examined for conformance to 3.2 an
49、d 3.3.4.6.3 Adhesion peel: Adhesion peel shall be determined in accordance with ASTM D 3330 except the test panels shall be coated as follows:a. Test panel-bare, not coated.b. Covered with tape to expose backing as the test substrate.c. Coated with MIL-C-6799 material applied in accordance with MIL-C-23760.d. Coated with epoxy-polyamide primer/polyurethane topcoat, color number 17925 of FED-STD-595, in accordance with 4.6.9.1.4.6.4 Accelerated aging: This test shall be performed in accordance with ASTM D 3611. At the conclusion of the aging, samples shall be examin
