1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref
2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2011 SAE International All rights reserved. No part of this pub
3、lication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970
4、outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/ARP5605AAEROSPACERECOMMENDEDPRACTICEARP5605 REV. A Issued 2001-09 Stabilized 2011-12
5、 Superseding ARP5605 Solid Composite Laminate NDI Reference Standards RATIONALEThis document has been determined to contain basic and stable technology which is not dynamic in nature. STABILIZED NOTICE This document has been declared “Stabilized” by the CACRC Technical Committee and will no longer b
6、e subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability of technical requirements. Newer technology may exist. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted withou
7、t license from IHS-,-,-SAE ARP5605A Page 2 of 11 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE ARP5605A Page 3 of 11 Copyright SAE International Provided by IHS under license with SAENot for Re
8、saleNo reproduction or networking permitted without license from IHS-,-,-SAE ARP5605A Page 4 of 11 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE ARP5605A Page 5 of 11 FIGURE 1 - G11 SOLID LAMIN
9、ATE STANDARD SET (numbers in circles represent skin thickness, in inches or mm in brackets, of each flat bottom hole) Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE ARP5605A Page 6 of 11 FIGURE
10、2 - FRONT AND BACK PHOTOS OF G11 SOLID LAMINATE SET Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE ARP5605A Page 7 of 11 Copyright SAE International Provided by IHS under license with SAENot for
11、 ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE ARP5605A Page 8 of 11 FIGURE 3 - G11-STD-1 - G11 STANDARD - 0.050“ (0.050 INCHES, 1.270 MM) Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without
12、license from IHS-,-,-SAE ARP5605A Page 9 of 11 FIGURE 4 - G11-STD-2 - G11 STANDARD - 0.180“ (0.180 INCHES, 4.572 MM) Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE ARP5605A Page 10 of 11 FIGURE
13、5 - G11-STD-3 - G11 STANDARD - 0.450“ (0.450 INCHES, 11.43 MM) Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE ARP5605A Page 11 of 11 FIGURE 6 - G11-STD-4 - G11 STANDARD - 1.000“ (1.000 INCHES, 25.40 MM) Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
