1、AEROSPACE STANDARD SCREW - OVAL FILLISTER, DRILLED HEAD, CADMIUM PLATED, STEEL UNS K00802, .1120-40 UNC - 2A AS116913THRU AS116924Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any me
2、ans, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org
3、ISSUED 2000-08REVISED 2012-10THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5305 AS116913THRU AS116924SHEET 1 OF 2REV. BPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering scie
4、nces. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, s
5、tabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS116913BRATIONALE DELETE REQUIREMENT TO MARK MANUFACTURERS IDENTIFICATION (DUE TO SIZE RESTRICTIONS) AND UPD
6、ATE CADMIUM PLATE NOTICE. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD AN116913 THRU AN116924, REVISION 2, NOTICE 1. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WIT
7、H QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - SCREW AEROSPACE STANDARD AS116913 THRU AS116924SHEET 2 OF 2REV. BSCREW - OVAL FILLISTER,
8、 DRILLED HEAD, CADMIUM PLATED, STEEL UNS K00802, .1120-40 UNC - 2A TABLE 1 - PART NUMBERS AND DIMENSION “L“ PARTNUMBER LAN116914 AN116915 AN116916 AN116917 AN116918 AN116919 AN116920 AN116921 AN116922 AN116923 AN116924 .240 - .260 .302 - .322 .365 - .385 .428 - .448 .490 - .510 .552 - .572 .615 - .6
9、35 .678 - .698 .740 - .760 .865 - .885 .990 - 1.010 NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. MATERIAL: STEEL PER AMS5061 (UNS K00802). 2. STRESS RELIEVE AFTER HEADING. MATERIA
10、L SPECIFICATION HARDNESS REQUIREMENT MUST BE MAINTAINED. 3. FINISH: CADMIUM PLATE PER AMS2400 4. MARK MATERIAL CODE “E4“ AS SHOWN PER AS269, RAISED OR DEPRESSED, .010 MAX PER AS478 CLASS A. 5. THREADS PER MIL-S-7742. 6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS ARE IN
11、 INCHES. 8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIO
12、US ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. MIL-S-7742 IS A U.S. GOVERNMENT PUBLICATION.
