1、AEROSPACE STANDARD SCREW, EXTERNALLY RELIEVED BODY, (SYNCHRO), CRES (UNS S30200 OR UNS S30300) AS17184Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical,
2、 photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1997-08REVISED 2014-0
3、1THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.CFEDERAL SUPPLY CLASS 5990 AS17184SHEET 1 OF 2REV. CPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely vol
4、untary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwr
5、ittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS17184CRATIONALE REVISE MINIMUM BREAK EDGE TO RESTORE ORIGINAL MS REQUIREMENT, UPDATE MATERIAL SPECIFICATION REFERENCE AND UNS DESIGNATIONS, AND ADD I
6、NTENDED USE NOTE. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS17184. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE
7、 TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - SCREW TABLE 1 - DIMENSIONS PARTNUMBER ANOMINAL THREAD LLENGTH BC +.000.003 D E F G H K MS17184-1 MS17184-2 (#4) .112-48UNF-2A (#6) .1
8、38-40UNF-2A .312.500.112.138.080.101.175.239.156.181.027.032.090.113.060.060.034.042AEROSPACE STANDARD AS17184SHEET 2 OF 2REV. CSCREW, EXTERNALLY RELIEVED BODY, (SYNCHRO), CRES (UNS S30200 OR UNS S30300) NOTES: 1. MATERIAL: CORROSION RESISTING STEEL UNS S30200 OR UNS S30300 PER AIR4127. 2. PROTECTIV
9、E TREATMENT: CORROSION RESISTING STEEL SHALL BE PASSIVATED. 3. THREADS: THREADS SHALL BE IN ACCORDANCE WITH FED-STD-H28. 4. DIMENSIONS IN INCHES. 5. TOLERANCES: UNLESS OTHERWISE SPECIFIED, DECIMAL .005, ANGLES 1 DEGREE. 6. BREAK EDGES .005 TO .015, UNLESS OTHERWISE SPECIFIED. INSIDE CORNERS .010 RAD
10、IUS MAX. 7. DO NOT USE UNASSIGNED PART NUMBERS. 8. INTENDED USE: THESE SCREWS ARE INCLUDED IN MS17183, “CLAMP ASSEMBLY (SYNCHRO)” 9. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO TH
11、E PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AIR ARE SAE INTERNATIONAL PUBLICATIONS. MS AND FED-STD ARE U.S GOVERNMENT PUBLICATIONS.
