1、 AEROSPACE STANDARD FITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO BEAM SEAL4000 PSI AND 5000 PSI /9/ AS1986Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electro
2、nic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1985-
3、12REAFFIRMED 2000-10REVISED 2015-02THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.F FEDERAL SUPPLY CLASS 4030AS1986 SHEET 1 OF 3 REV. F PROCUREMENT SPECIFICATION: /4/ AS85720SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineerin
4、g sciences. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed,
5、 stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS1986F RATIONALE UPDATE OF MAXIMUM WEIGHT VALUES VERIFIED THROUGH CAD MODELING, AND UPDATE OF DRAWING INTE
6、RPRETATION SPECIFICATION. FIGURE 1 - ADAPTER, ASSEMBLY TABLE 1A - DIMENSIONS A - F BASIC NO. AS1986 /18/ SIZE CODE (NOMINAL TUBE SIZE) A THREAD AS8879 B THREAD AS8879 C D E F +.005 .002 02 .125 .3125-32UNJEF-3A .2160-28UNJF-3A .400 .265 - .271 .090 - .096 .154 03 .188 .3750-28UNJS-3A .2500-28UNJF-3A
7、 .468 .323 - .329 .122 - .128 .186 04 .250 .4375-24UNJS-3A .3125-24UNJF-3A .514 .377 - .383 .169 - .175 .239 05 .312 .5000-24UNJS-3A .3750-24UNJF-3A .624 .440 - .446 .231 - .237 .301 06 .375 .5625-20UNJS-3A .4375-20UNJF-3A .700 .490 - .497 .294 - .300 .364 08 .500 .7188-20UNJS-3A .5625-18UNJF-3A .81
8、4 .646 - .654 .398 - .408 .482 10 .625 .8438-18UNJS-3A .6875-24UNJEF-3A 1.040 .763 - .772 .493 - .503 .625 12 .750 1.0000-16UNJ-3A .8125-20UNJEF-3A 1.170 .910 - .919 .604 - .614 .737 14 .875 1.1250-16UNJ-3A .9375-20UNJEF-3A 1.341 1.034 - 1.044 .729 - .739 .868 16 1.000 1.2500-14UNJS-3A 1.1250-18UNJE
9、F-3A 1.456 1.148 - 1.158 .839 - .851 1.000 20 1.250 1.5781-14UNJS-3A 1.3125-18UNJEF-3A 1.782 1.476 - 1.486 1.073 - 1.086 1.225 24 1.500 1.8438-14UNJS-3A 1.6250-18UNJEF-3A 2.031 1.741 - 1.751 1.307 - 1.320 1.502 (A) THREAD AEROSPACE STANDARD AS1986 SHEET 2 OF 3 REV. F FITTING ASSEMBLY, ADAPTER RING L
10、OCKED PORT CONNECTION TO BEAM SEAL 4000 PSI AND 5000 PSI /9/ TABLE 1B - DIMENSIONS G P AND WEIGHT BASIC NO. AS1986 /18/ SIZE CODE G MIN H J +.010 .005 K +.000 .015 L +.010 .005 M .007 N MIN P WEIGHTLB/EA MAX 02 .246 .317 .519 .300 .125 .192 .141 24 .009 03 .278 .349 .550 .355 .125 .192 .164 26 .012
11、04 .331 .400 .592 .355 .125 .192 .197 30 .016 05 .393 .491 .592 .381 .125 .192 .197 36 .021 06 .456 .544 .633 .395 .125 .210 .205 36 .027 08 .574 .670 .646 .430 .125 .210 .218 40 .038 10 .717 .824 .710 .465 .125 .210 .274 38 .066 12 .891 .981 .760 .527 .157 .220 .303 40 .088 14 1.022 1.118 .778 .572
12、 .157 .220 .318 50 .111 16 1.154 1.251 .808 .564 .157 .220 .338 36 .137 20 1.379 1.466 .832 .569 .157 .240 .335 56 .198 24 1.656 1.768 .917 .608 .157 .240 .420 81 .299 NOTES: 1. MATERIAL: a. FITTING: 6Al-4V TITANIUM ALLOY PER AMS4928, AMS4965, OR AMS4967. b. LOCKRING: A286 CORROSION RESISTANT STEEL
13、PER AMS5731, AMS5732, AMS5734, AMS5737, OR AMS5853. 2. HEAT TREATMENT: a. FITTING: 130 KSI UTS MIN. b. LOCKRING: 34-40 HRC. 3. FINISH: a. FITTING: ANODIC TREATMENT PER AMS2488, TYPE 2. b. LOCKRING: PASSIVATE PER AMS2700, TYPE 2. /4/ PROCUREMENT SPECIFICATION: a. AS85421 (SIZES 02, 03, 05, 14, 20, AN
14、D 24): PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS85421 FOR THIS STANDARD. SEE http:/www.eAuditN FOR CURRENT QPL ONLINE. b. AS85720 (SIZES 04, 06, 08, 10, 12, AND
15、 16): PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS85720 FOR THIS STANDARD. SEE http:/www.eAuditN FOR CURRENT QPL ONLINE. /5/ SEALING SURFACE: NO VISIBLE DEFECTS. T
16、O BE PROTECTED FOR SHIPMENT. /6/ LOCKRING RETAINED ON FITTING BY CONTROLLED INTERFERENCE FIT. AEROSPACE STANDARD AS1986 SHEET 3 OF 3 REV. F FITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO BEAM SEAL 4000 PSI AND 5000 PSI /9/ /7/ SEALING ANGLES: a. SIZES -02 AND -03: 3 00 TO 3 30 b. SIZES -04
17、 AND LARGER: 8 30 TO 9 00 /8/ IDENTIFICATION: a. MARK AT LOCATION(S) SHOWN PER AS478 METHOD 2 OR 15, MANUFACTURERS NAME, TRADEMARK, OR CAGE CODE. b. BAG AND TAG PER AS478, METHOD 35D, MANUFACTURERS NAME, TRADEMARK, OR CAGE CODE AND PART NUMBER. /9/ WORKING PRESSURE: THIS PART IS DESIGNED FOR USE IN
18、HYDRAULIC SYSTEMS COMPATIBLE WITH TITANIUM. a. SIZE -04, -06, -08, -10, -12, AND -16: 5000 PSI (20 000 PSI BURST PRESSURE) SYSTEMS. b. ALL OTHER SIZES: 4000 PSI (16 000 PSI BURST PRESSURE) SYSTEMS. 10. ADAPTERS TO BE INSTALLED PER AS1301 INTO BOSS CAVITIES PER AS1300. 11. A CHANGE BAR (l) LOCATED IN
19、 THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS.
20、 CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 12. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. 13. INTERPRETATION OF DRAWING PER AS4296. 14. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIRE
21、MENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra AND SEALING SURFACE TO BE 63 MICROINCHES Ra. 15. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 16. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 17. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, ANGULAR DIMENSIONS 5. /18/ EXAMPLE OF PART NUMBER:
