1、 AEROSPACE STANDARD CRIMPING TOOLS, TERMINAL, HAND, WIRE TERMINATION; IN-SERVICE INSPECTION GAGE FOR AS22520/41 CRIMP TOOLS AS22520/42Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by an
2、y means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.
3、org ISSUED2011-09 REAFFIRMED2016-11 THIRD ANGLE PROJECTION CUSTODIAN: AE-8C2 FEDERAL SUPPLY CLASS 5220 AS22520/42 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS22520 SAE Technical Standards BoardRules providethat:“This reportis publishedbySAE toadvancethestateoftechnicaland engineering sciences. The use
4、 of this report isentirely voluntary, andits applicability andsuitability for any particularuse, includingany patentinfringement arising therefrom,is the soleresponsibility of theuser.”SAE reviews eachtechnical reportatleast every fiveyears atwhichtimeitmay berevised,reaffirmed, stabilized,orcancell
5、ed. SAE invites yourwrittencomments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS22520/42 RATIONALE AS22520/42 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THE REQUIREMENTS FOR P
6、ROCURING THE CONTACTS DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF: SAE AS22520 FIGURE 1 INSPECTION GAGE FOR M22520/41-01 TABLE 1 WIRE BARREL INSPECTION GAGE DESIGN CONFIGURATION AND APPLICATION PART NO. B DIA TOOL TO BE INSPECTED GO DIM. (GREEN) NO-GO DIM. (RED) M225
7、20/42-01 .1690-.1693 .1749-.1750 M22520/41-01 FIGURE 2 INSPECTION GAGE FOR M22520/41-02 AEROSPACE STANDARD AS22520/42 SHEET 2 OF 2 CRIMPING TOOLS, TERMINAL, HAND, WIRE TERMINATION; IN-SERVICE INSPECTION GAGE FOR AS22520/41 CRIMP TOOLS TABLE 2 INSULATION BARREL INSPECTION GAGE DESIGN CONFIGURATION AN
8、D APPLICATION PART NO. D DIA W MAX TOOL TO BE INSPECTED GO DIM. (GREEN) NO-GO DIM. (RED) M22520/42-02 .1640-.1643 .0839-.0840 .171 M22520/41-01 REQUIREMENTS: AS SPECIFIED IN AS22520. 1. DIMENSIONS UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES AS SPECIFIED. CONFIGURATION IS OPTIONAL WITHIN DEF
9、INED DIMENSIONS. TOLERANCES ARE DECIMALS .005 INCHES. DIMENSIONS B AND D APPLY AFTER PROTECTIVE COATING (SEE REQUIREMENT 3). 2. MATERIAL WIRE BARREL GAGE PINS AND INSULATION BARREL GAGE: ALLOY TOOL STEEL PER ASTM A681, ASTM-A295, OR EQUIVALENT (CLASS OPTIONAL). HARDEN TO ROCKWELL C58-64. WIRE BARREL
10、 GAGE HANDLE: ALUMINUM ALLOY, ASTM B211 ALUMINUM AND ALUMINUM-ALLOY BAR, ROD, AND WIRE 3. FINISH GAGE PINS: CHROME PLATE WITH ADEQUATE COVERAGE FOR CORROSION AND WEAR RESISTANCE PER AMS-QQ-C-320 PLATING CHROMIUM, CLASS I, TYPE II WITH A THICKNESS OF .00003 INCHES MINIMUM. WIRE BARREL GAGE HANDLE: HA
11、NDLE IS ANODIZED IN ACCORDANCE WITH MIL-A-8625. 4. MARKING UNLESS OTHERWISE SPECIFIED, STAMPING SHALL BE INDENTED. LASER ETCHING IS ALSO ACCEPTABLE. MANUFACTURERS NAME SHALL BE COMPLETE OR BE AN AIR1351 LISTED LOGO. 5. STORAGE CONTAINER: EACH GAGE SHALL BE FURNISHED WITH A SUITABLE CONTAINER. APPLICATION NOTES: TOOL IS USED AS A GO/NO-GO VERIFICATION INSPECTION GAGE FOR AS22520 TOOLS SPECIFIED IN TABLE 1 AND 2.
