1、Copyright 2000 Society of Automotive Engineers, Inc. Printed in the U.S.A.All rights reserved. .TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX: (724) 776-0790 SAE WEB ADDRESS: http:/www.sae.org400 Commonwealth Drive, Warrendale, PA 15096-0001SAE Technical StandardsBoard Rulesprovidethat:“Thisreport i
2、s published by SAEtoadvance thestateoftechnical and engineeringsciences. The useofthis reportisentirelyvoluntary, and its applicabilityand suitability for any particularuse, includingany patent infringement arising therefrom, isthe soleresponsibility of the user.”SAE reviews each technical report at
3、 least every five years at whichtime it maybereaffirmed, revised, or cancelled. SAE invites your writtencomments and suggestions.SHEET 1 OF 5AS22759/4THIRD ANGLE PROJECTIONAEROSPACE STANDARDAS22759/4ISSUED2000-09WIRE, ELECTRIC, FLUOROPOLYMER-INSULATED,TFE-GLASS-FEP, MEDIUM WEIGHT, SILVER-COATEDCOPPE
4、R CONDUCTOR, 600-VOLTPREPARED BY SAE SUBCOMMITTEE AE-8DFEDERAL SUPPLY CLASS 6145NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-W-22759/4C AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF S
5、AE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-W-22759/4C. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD
6、 (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE
7、 EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE A
8、ND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-400 Commonwealth Drive, Warrendale, PA 15096-0001WIRE, ELECTRIC, FLUOROPOLYMER-INSULATED,TFE-GLASS-FEP, MED
9、IUM WEIGHT, SILVER-COATEDCOPPER CONDUCTOR, 600-VOLTAEROSPACE STANDARD AS22759/4SHEET 2 OF 5AS22759/4THE REQUIREMENTS FOR ACQUIRING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE ISSUE OF THE FOLLOWING SPECIFICATION LISTED IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE IND
10、EX OF SPECIFICATIONS AND STANDARDS (DODISS) SPECIFIED IN THE SOLICITATION: MIL-W-22759.TABLE I. CONSTRUCTION DETAILS.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-400 Commonwealth Drive, Warrendale,
11、PA 15096-0001WIRE, ELECTRIC, FLUOROPOLYMER-INSULATED,TFE-GLASS-FEP, MEDIUM WEIGHT, SILVER-COATEDCOPPER CONDUCTOR, 600-VOLTAEROSPACE STANDARD AS22759/4SHEET 3 OF 5AS22759/4TABLE II. PERFORMANCE DETAILS.REQUIREMENTS:Temperature rating: 200C (392F) max conductor temperature.Voltage rating: 600 volts (r
12、ms) at sea level.Spark test of primary insulation: Not required.Impulse dielectric test: 8.0 kilovolts (peak), 100 percent test.Insulation resistance: 5,000 megohms for 1000 ft (min).Wrap test:Mandrel test required - no cracking.Dielectric test after mandrel wrap, 2500 volt (rms), 60Hz.Blocking: 200
13、 2C (392 3.6F).Shrinkage: 0.125 inch max at 200 2C (392 3,6F).Wicking:Size 22 through 12 - Procedure II; 2.0 percent (max) weight increase, 0.750 inch (max) dye travel.Size 10 through 00 - No requirement.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction
14、or networking permitted without license from IHS-,-400 Commonwealth Drive, Warrendale, PA 15096-0001WIRE, ELECTRIC, FLUOROPOLYMER-INSULATED,TFE-GLASS-FEP, MEDIUM WEIGHT, SILVER-COATEDCOPPER CONDUCTOR, 600-VOLTAEROSPACE STANDARD AS22759/4SHEET 4 OF 5AS22759/4Low temperature (cold bend):Bend temperatu
15、re - -65 2C (-85 3.6F).Dielectric test, 2500 volts (rms), 60Hz.Thermal shock:Oven temperature, 200 2C (392 3.6F).Maximum change in measurement -Sizes 22 through 12 - 0.060 inch.Sizes 10 through 8 - 0.100 inch.Sizes 6 through 00 - 0.125 inch.Flammability: Post-flame dielectric test not required.Life
16、cycle:Oven temperature 250 2C (482 3.6F).Dielectric test, 2500 volts (rms), 60Hz.Dielectric test after immersion: 2500 volts (rms), 60Hz.Humidity resistance: 5,000 megohms for 1000 ft, min insulation resistance after humidity exposure.Surface resistance:Sizes 22 through 12 - 500 megohm-inches (min),
17、 initial and final readings.Sizes 10 through 00 - No requirement.Smoke: 200C (392F).Acid resistance:Required.Dielectric test, 2500 volts (rms), 60Hz.Color: In accordance with MIL-STD-104, Class 1; white preferred.Color striping or banding durability: 250 cycles (500 strokes) (min), 500 grams weight.
18、 Test not required if marking is under clear FEP jacket.Identification durability: 125 cycles (250 strokes) (min), 500 grams weight. Test not required if marking is under clear FEP jacket.Wire length requirements: Schedule A.Supersession data: The wire of this specification sheet, by part number, re
19、places and supersedes the wire of MS90294(AS) (canceled) in accordance with table III.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-400 Commonwealth Drive, Warrendale, PA 15096-0001WIRE, ELECTRIC, FL
20、UOROPOLYMER-INSULATED,TFE-GLASS-FEP, MEDIUM WEIGHT, SILVER-COATEDCOPPER CONDUCTOR, 600-VOLTAEROSPACE STANDARD AS22759/4SHEET 5 OF 5AS22759/4TABLE III. SUPERSESSION BY PART NUMBER.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-
