1、AEROSPACE STANDARDINSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE, SILICONE RUBBER, FLEXIBLEAS23053/10Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical,
2、photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED2016-10THIRD ANGLE PROJECT
3、IONCUSTODIAN: AE-8/AE-8DFEDERAL SUPPLY CLASS5970AS23053/10SUPERSEDES AMS-DTL-23053/10ASHEET 1 OF 4PROCUREMENT SPECIFICATION: AS23053SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis reportis entirely vo
4、luntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyears at whichtime it may berevised, reaffirmed, stabilized, or cancelled. SAEinvites your w
5、rittencomments and suggestions.SAE values your input. To provide feedback on thisTechnical Report, please visit http:/standards.sae.org/AS23053/10RATIONALETHIS IS A CONVERSION OF AMS-DTL-23053/10 INTO AN AEROSPACE STANDARD WHICH INCLUDES QUALIFICATION AND REQUIREMENTS FOR A QUALIFIED PRODUCTS LIST.N
6、OTICETHE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENTAND THE LASTEST ISSUE OF AS23053.REQUIREMENTS1. DIMENSIONS AND PROPERTIES IN INCH/POUND UNITS AND THE FAHRENHEIT TEMPERATURES ARE PRIMARY; DIMENSIONS AND PROPERTIES IN SI UNITS AND THE CELSIUS TEMPERATURES
7、 ARE SHOWN AS THE APPROXIMATE EQUIVALENTS OF THE PRIMARY UNITS AND ARE PRESENTED ONLY FOR INFORMATION.2. POLYMER TYPE: THE BASE ELASTOMER USED IN FORMULATING THIS SLEEVING SHALL BE A SILICONE.CONTINUOUS OPERATING.3. TEMPERATURE RANGE: -103 F TO +347 F (-75 C TO +175 C).4. COLOR: THE SLEEVING SHALL B
8、E FURNISHED IN A BLACK COLOR THAT CONFORMS TO THE REQUIREMENTS OF CLASS II OF MIL-STD-104 (SEE 1.3).5. LONGITUDINAL CHANGE: +3, -10%.6. PART NUMBER: THE PART NUMBER SHALL BE AS LISTED BELOW:M23053/10 - X XX - XEXAMPLE: BLACK, 2.000 INCH (50.80 MM) AS SUPPLIED ID SLEEVING SHALL BE IDENTIFIED AS M2305
9、3/10-012-0.7. DIMENSIONAL LIFE: THE DIMENSIONAL LIFE OF A PRODUCT APPLIES TO THE EXPANDED I.D., RECOVERED I.D. AND WALL THICKNESS DIMENSIONS OF THE PRODUCT AS SOLD BY THE MANUFACTURER, DISTRIBUTORS AND REBRAND DISTRIBUTORS. AS23053/10 PRODUCTS CAN BE EXPECTED TO HAVE A MINIMUM DIMENSIONAL LIFE OF 1
10、YEAR WHEN STORED BETWEEN 32 TO 95 F (0 TO 35 C). PRODUCTS STORED ABOVE THESE CONDITIONS MAY NOT MEET THE MINIMUM EXPANDED I.D. REQUIREMENTS OF THE DETAIL SPECIFICATION. A PRODUCT MAY BE USED BY THE FINAL PURCHASER BEYOND THE EXPECTED MINIMUM DIMENSIONAL LIFE, AS LONG AS THE EXPANDED I.D., RECOVERED
11、I.D. AND WALL THICKNESS OF THE PRODUCT MEET THE REQUIREMENTS OF THIS SPECIFICATION AT THE TIME OF USE.8. UNRESTRICTED SHRINKAGE: TEST METHOD 5.5.2; 392 F 4 F (200 C 2 C) FOR 10 MINUTES.COLOR CODE DESIGNATOR (SEE 1.3)SIZE IDENTIFIER (SEE TABLE 1)CLASS (WHERE NO CLASSES ARE SPECIFIED IN THESPECIFICATI
12、ON SHEET, THE NUMERIC “0” IS USED)SPECIFICATION SHEETAEROSPACE STANDARD AS23053/10SHEET 2 OF 4INSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE, SILICONE RUBBER, FLEXIBLETABLE 1 - CONSTRUCTION DETAILS, INCHES (MM) 1/PART NUMBER 3/ AS SUPPLIED AFTER UNRESTRICTED SHRINKAGEID MINIMUM ID MAXIMUM WALL THIC
13、KNESS 2/M23053/1-101-0 .125 (3.2) .071 (1.8) .020 .006 (0.5 0.2)M23053/1-102-0 .250 (6.4) .143 (3.6) .035 .010 (0.9 0.3)M23053/1-103-0 .375 (9.5) .214 (5.4) .040 .010 (1.0 0.3)M23053/1-104-0 .500 (12.7) .286 (7.3) .048 .015 (1.2 0.4)M23053/1-105-0 .625 (15.9) .357 (9.1) .052 .015 (1.3 0.4)M23053/1-1
14、06-0 .750 (19.1) .428 (10.9) .057 .015 (1.4 0.4)M23053/1-107-0 .875 (22.2) .500 (12.7) .065 .015 (1.7 0.4)M23053/1-108-0 1.000 (25.4) .570 (14.5) .070 .020 (1.8 0.5)M23053/1-109-0 1.250 (31.8) .714 (18.1) .087 .020 (2.2 0.5)M23053/1-110-0 1.500 (38.1) .857 (21.8) .095 .020 (2.4 0.5)M23053/1-111-0 1.
15、750 (44.5) 1.000 (25.4) .107 .020 (2.7 0.5)M23053/1-111-0 2.000 (50.8) 1.140 (29.0) .110 .020 (2.8 0.5)1/ Diameter limits for the object to be enclosed shall be as recommended in technical data.2/ Wall thickness values are less when shrinkage is restricted.3/ The color code identified is the standar
16、d color.TABLE 2 - PHYSICAL PROPERTIESCHARACTERISTIC REQUIREMENT TEST PROCEDURE AND CONDITION(SEE AS23053)AS SUPPLIED:ID, MINIMUM TABLE 1 5.3.1HEAT SHOCK NO CRACKS, FLOWING OR DRIPPING 5.8 572 F 7.2 F (300 C 4 C)NO MANDREL BENDTENSILE STRESS AT 100 PERCENT, PSI (MPA), MAXIMUM1000(6.9) 5.12.2 ASTM D41
17、2COLD IMPACT NO CRACKING 5.7.2 -105 F 4 F (-75 C 2 C)LONGITUDINAL STRIP. ASTM D746DIELECTRIC STRENGTH, VOLTS/MIL (KV/MM), MINIMUM200(7.9) 5.2 ASTM D2671RESTRICTED SHRINKAGE NO CRACKS 5.6 392 F 4 F (200 C 2 C)VOLTAGE WITHSTAND PASS 5.6.2CAEROSPACE STANDARD AS23053/10SHEET 3 OF 4INSULATION SLEEVING, E
18、LECTRICAL, HEATSHRINKABLE, SILICONE RUBBER, FLEXIBLETABLE 2 - PHYSICAL PROPERTIES (CONTINUED)CHARACTERISTIC REQUIREMENTTEST PROCEDURE AND CONDITION(SEE AS23053)AFTER UNRESTRICTED SHRINKAGE:ID, MAXIMUM TABLE 1 5.3.2WALL THICKNESS TABLE 1 5.3.3TENSILE STRENGTH, PSI(MPA), MINIMUM600(4.2) 5.13 ASTM D638
19、 20 INCHES/MINUTEULTIMATE ELONGATION,PERCENT, MINIMUM200 5.13 ASTM D638, 20 INCHES/MINUTEVOLUME RESISTIVITY, OHM-CM, MINIMUM1 X 1011 5.2 ASTM D876WATER ABSORPTION, PERCENT, MAXIMUM1.0 5.2 ASTM D570, 24 HOURS AT 23 CCORROSION NO CORROSION OR PITTING 5.10.1 AND 5.10.2,347 F 4 F (175 C 2 C),16 HOURSHE
20、AT RESISTANCE,PROPERTIES AFTER:5.9 392 F 4 F (200 C 3 C), 168 HOURSTENSILE STRENGTH, PSI(MPA), MINIMUM450(3.1)ULTIMATE ELONGATION,PERCENT, MINIMUM100FLUID RESISTANCE,PROPERTIES AFTER:5.11TENSILE STRENGTH, PSI (MPA), MINIMUM300 (2.1)ULTIMATE ELONGATION,PERCENT, MINIMUM100FLAMMABILITY SELF-EXTINGUISHI
21、NG, 1MINUTE, 25 PERCENT MAXIMUM OF INDICATOR FLAG BURNED5.14 PROCEDURE B, ASTM D2671FUNGUS RESISTANCE PROPERTIES AFTER:TENSILE STRENGTH, PSI(MPA), MINIMUMULTIMATE ELONGATION,PERCENT, MINIMUMDIELECTRIC STRENGTH,VOLTS/MIL (KV/MM), MINIMUMNO GROWTHOR600 (4.2)200200 (7.9)5.17 ASTM G21OR5.17 ISO 846AEROS
22、PACE STANDARD AS23053/10SHEET 4 OF 4INSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE, SILICONE RUBBER, FLEXIBLEAPPLICATION NOTES 1. INTENDED USE: HEAT SHRINKABLE, FLEXIBLE, SILICONE SLEEVING IS INTENDED FOR USE IN HIGH OR LOW TEMPERATURE APPLICATIONS OR IN ABLATIVE APPLICATIONS.SPECIFICATION NOTES1.
23、REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
